Question about Navigon 2110 Series Satellie GPS Receiver

1 Answer

White screen on start up

Some sound

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

2 things to do...use a paperclip and press the reset button hold it for 5 seconds. THEN hold down the power on button for over 10 secs (keep holding while it shows version number) and it will perform a factory reset. You will likely lose any settings and addresses, but better that than no GPS unit.

Posted on Jul 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tomtom troubleshooting


check the GPS with the dealership...i suspect your screen is faulty

Oct 22, 2013 | GPS Devices

1 Answer

Garmin nuvi 1350 screen black cracks


it sounds like the unit has been dropped and has cracked on the inside of the screen. we see this a lot with mobile phones. you may need to have the internal screen replaced.

Jul 12, 2010 | Garmin nuvi 1350 Car GPS Receiver

1 Answer

My screen is white but I still have sound. HOw do


This is an indication that the LCD display is defective and needs to be replaced. Please see this link:

http://www.sharc.net/gps_LCD_repair.htm



- Jim

Jan 12, 2010 | Garmin nuvi 260W GPS Receiver

1 Answer

The screen turned white for about an hour, does not come on


try the reset first (little pin hole on the side) using a paper clip, hold it in for 10-15 seconds. if that fails, plug in your charger and charge for awhile the press and hold the power button for upto 15 seconds till it starts. it sounds like you might have multiple problems. the screen going white normally indicates a bad screen but might just need reseated (ribbon cable)..try what i suggested first, if none of those work, let me know and we will see what else we can do.

bill

Aug 18, 2009 | Magellan Roadmate 1200 Car GPS Receiver

1 Answer

I have the White Screen of Death


Try pressing the reset button underneath the antenna and if this doesn't help, then you'll need to have the LCD display replaced.

- Jim
SHARCNET-USA

Dec 22, 2008 | Garmin Nuvi 350 Car GPS Receiver

1 Answer

While using navman the screen went white and will not work any more only 3 months old lost warranty


My screen in my iway 350 is white i hear the sound but theres no picture someone anyone help please

Apr 18, 2008 | GPS Devices

2 Answers

Garmin Nuvi 260 - white screen


Hit the side of the Garmin a few times while it is on. I did this to mine, and now I can see the screen like before.

Apr 05, 2008 | Garmin nuvi 350 GPS Receiver

1 Answer

White screen


dorub,

you do not get any sounds right?  If no, you need a  new hard drive.  There is no magic fix for a white screen.  Either your hard drive is corrupted..  if no sound it's your hard drive.  If there's is sound it could be your lcd connector.   As a matter of fact it could be your hard drive cable.  At your own risk feel free to open up the mysterious unit and make sure the big metal rectangular prism in there is properly connected.

Sep 30, 2007 | Magellan RoadMate 700 GPS Receiver

1 Answer

MRM 700 won't start; screen flashes white . . . help.


stonelinton, It's not your LCD, otherwise you would have heard the sound of buttons being pushed. If your units first screen is white and there is no logo screen or any legible images, then it's your NAND flash on your main board. The first image produced upon boot is the blue magellan screen. This is produced from the NAND flash and will show it no matter if a hard drive is present or not. After the Magellan screen it pulls images from the hard drive. So, it is the mainboard and the only way to fix it is to send it to Magellan repair and they will have to put in a new mainboard then reprogram your serial number, etc.

Jun 07, 2007 | Magellan RoadMate 700 GPS Receiver

1 Answer

The screen images are in reverse


For clarification: You turn on your unit, the blue magellan logo appears clearly, but then the screen slowly starts turning white. Turning the unit off/on fixes the white but images are in reverse. CAUTION: It would help if you were grounded in some way prior to proceeding. Also, of course do this at your own risk. Make sure the cable going from the main board to the LCD is making a solid connection: 1. Take screws out of rear housing 2. Slightly seperate the rear/front housing 3. Disconnect the RF cable attached on the corner of the main board. 4. Pull off (or locate if they already fell off) 4 O rings from the screw mounts. 5. Fold over mainboard ontop of rear housing 6. Use fingernail or tweezers to lift up the plastic locking mechanism that attaches your LCD to the backside of your mainboard. 7. Pull out LCD cable, inspect for "gunk" on conacts (clean if necessary) 8. Shove cable back into slot on mainboard 9. Press down locking mechanism 10. fold mainboard back over 11. Put 4 O rings back on screw mounts 12. PLUG RF CABLE BACK IN! (signal will be zero if this doesn't happen) 13. Fit together front/back and screw back in.

Mar 22, 2007 | Magellan RoadMate 700 GPS Receiver

Not finding what you are looking for?
Navigon 2110 Series Satellie GPS Receiver Logo

Related Topics:

970 people viewed this question

Ask a Question

Usually answered in minutes!

Top Navigon GPS Devices Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

roedene

Level 1 Expert

9 Answers

Will Halftowaite

Level 3 Expert

503 Answers

Are you a Navigon GPS Device Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...