Question about Ford Code-Alarm Code Alarm Transponder

1 Answer

52 tdci mondeo, keyfob needs programming

Recently bought a 52 plate tdci with 2 keys one a basic chipped key the other a 3 button keyfob, to later find out the innerds were completely missing, put a new chip bit on from a scrap key but it needs to be set for the car has this got to be done by computer or can it be done like te older mondeo's by turning ignition on off etc etc, thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 99 Answers

I am afraid on this model has to go to dealer to be reprogrammed.


Posted on Feb 04, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Immobiliser flashing on fiesta tdci

you've lost signal in the chip in the key you/ve got to have it programed dont have to take it to dealer.

Aug 06, 2013 | Directed Electronics DEI GM Immobilizer...

1 Answer

I bought a used 2007 Expedition and the door pad remote entry does not work. I have one AUTOPAGE XT-33 remote that came with the car. I turned the key in the driver's side door lock and the alarm...

I'm not sure exactly if this is what you're looking for, but if you're trying to program a new keyfob remote, follow these steps:

  1. Turn the key in the ignition from off to run 8 times within 10 seconds. You'll hear the door locks cycle (lock and unlock) three times to confirm that the car is in learning mode.
  2. Within 20 seconds, press any button on your keyfob. The locks will cycle again to confirm.
  3. Repeat step two with any additional keyfobs you wish to program.
  4. Turn the ignition off. The locks will cycle again to confirm the end of programming mode.
As for the alarm type, you would probably want to contact Ford and ask them. As for the door pad, while you're on the phone with Ford you'll need to get the factory door code. You might be lucky and find it written somewhere in/on the car or inside the book that came with the car, unless the new owner got rid of it.

Jun 28, 2011 | Ford Vehicle Security Systems

1 Answer

Hi, my old remote key pad used to lock itself so if I bumped it in my pocket it wouldnt start. I bought a new 2 way recently but the key pad stays unlocked. How do I get it lock?

Press and hold the "f" for 8 seconds to access the remote programming features. The remote will emit one long beep and the LEDs will illuminate. Press the unlock button to access the remote programming features. Two transmit LEDs will flashes and two beeps indicate the remote programming features are accessed. Press the lock button on the remote( LED on indicates auto locking on, LED off indicates auto locking off). Press and release "f" button to exit programming.

Apr 12, 2011 | Python 872 Responder LE keyless entry...

1 Answer

Audiovox Pursuit Pro keyfob reprogram

if thats the picture of the transmitter to program it you have to : turn the ignition to on position. press and release the programming switch 3 times... press and hold,for 3 seconds, the buttonof the transu wish to add until the parking lights flash. this would mean the transmitter has been learned. repeat step 3 for each transmitter... turn the ignition off to exit the program mode..
do not let 15 seconds pass between steps.

Feb 11, 2010 | Audiovox Car APS921 Remote Starter -...

1 Answer

Key chip gone down on R reg ford fiesta combe 1800 Diesel

Try this useful website for FORD keys and how to program them

It`s mainly for the MONDEO but also useful for other Ford models

Nov 01, 2009 | Vehicle Security Systems

1 Answer

My alarm fob broke. Bought a new one at the dealer for 35 dollars. then tells me it will cost 109 dollars to program. Can i do it myself

There is an excellent step by step guide at this web site:
Even though it shows a Sorento, your Sedona should be the same. Just look for the black plastic box under the hood marked "Diagnostics" and follow the rest of the steps. ** WARNING ** You are putting your car's computer into programming mode when doing this. Proceed at your own risk and follow the guide EXACTLY.
Re-programming Key Fobs
By Redzman
Tools Needed:
  • 1 or 2 OEM Key Fobs.
  • 1.5 foot of electrical wire, with ends stripped, approximately 22 gauge. (Jumper Wire).
  • Open the hood of your SUV.

  • Behind the battery on the drivers side is a plastic covered connector labeled Diagnostics.

  • Open the plastic cover on the Diagnostics port by pulling up on the edge near the FRONT of the vehicle.

  • Get your prepped/stripped jumper wire and place one end in connector 6 as shown in the pictures.

  • 04.gif
  • Run the other end of the jumper wire to the POSITIVE terminal on your battery, you can just push it into the little opening on there so it stays in place for a few minutes.

  • Get into your vehicle with your key fobs.

  • Put one key into your ignition and turn to ON position, DO NOT start your vehicle.

  • If you just have ONE key fob to reprogram, when you turn the vehicle to ON, hold the LOCK button down for 3 seconds, the lights on the dash will go off, and you are done. Turn the key off, disconnect the wire, and try the key fob.

  • If you have TWO key fobs to reprogram, turn the key to ON, hold the first LOCK button for 1 second, then the second one for 1 second. Turn the key off after the lights on the dash go off and remove the jumper wire. Test both Key Fobs.

Jul 22, 2009 | Vehicle Security Systems

2 Answers

Chrysler PT Cruiser remote key fob how to program?

1. Insert the key into the ignition switch and turn the switch to the ON position.
2. Press and hold the Unlock button on the transmitter between four and ten seconds.
3. continue to hold the unlock button and press the Panic button. A chime will sound to indicate that the transmitter programming mode has been entered.
4. Press a button on all transmitters to be programmed to the system, including any previously programmed transmitters. A chime will sound when each transmitter has been programmed.
5. Turn the ignition switch off to exit the transmitter programming mode."

Mar 28, 2009 | Vehicle Security Systems

1 Answer

Ford mondeo alarm activates by it self.

have you managed to sort it? mine is the same. have you any advice on the issue ?

Jan 31, 2009 | Ford Code-Alarm Code Alarm Transponder

2 Answers

2006 Mazda 5 keyless remote fob

I am a technition for mazda, and if the lights are coming on to the keyfobs, the batteries are fine. What procedure did you follow?
1. Take key out of ignition
2. Shut all doors
3. Open drivers door
4. Insert key to ignition
5. Cycle between On & Lock 3 times, leaving key in Lock
6. Close and open the drivers door 3 times, leaving the door open
7. The Locks should cycle.
8. Press the Panic button on the remote twice.

Jan 31, 2009 | SMC Alarm & Keyless Entry System for Mazda...

Not finding what you are looking for?
Ford Code-Alarm Code Alarm  Transponder Logo

471 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Vehicle Security Systems Experts

xxxxxx xxx

Level 3 Expert

4724 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Larry Spears
Larry Spears

Level 3 Expert

625 Answers

Are you a Ford Vehicle Security System Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides