Question about Honeywell Electronic Programmable Heat/Cool Thermostat - CT3300A100 Heater

2 Answers

Chromotherm 1V plus how to put intoAdaptive Intelligent Recovery

This thermostaat was installed when the new furnace was installed almost 5 years ago. I love ther flexability of this Thermostaat but I had the furnace installer come back after a few weeks and disable the Adaptive Recovery function. Our circumstances have changed and I am considering changing back to the Adaptive Intelligent Recovery mode but I do not want to pay $100 to have the guy make a house call. So with that in mind, how really difficult is it to make the change my self. All the manual says is to have the furnace techician come and do it. I am pretty handy with these kinds of things, I configure and put together computers for people as a sideline to my retirement so I am fairly kowledgeable.
Thanks for your help in this matter.

ralph

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 88 Answers

You are going to need the installers manual, inside is the installer set up functions, it will have the code to get you to the adaptive intelligence setting on your stat, I have found living here in the northwest that the A.I.R. setting does not function properly, to cold here for it to function right, people were complianing that it would start coming on well before the programed settings, what it does is anticipates the need of the home and reacts. We here have to shut the function off. Hope that helps

Posted on Jan 20, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I finally found an installation guide online for this t'staat. All I had t do was go into installers mode on the controller and change a value from "0" to "1". It told me which buttons to push to get into installers mode and which item # to change. In my case it was item number 13.

Posted on Jan 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Furnace blowing warm air, ac overheats


Sounds like it is tripping on it's high pressure switch. This could be caused by a dirty condenser coil, overcharge of refrigerant, or non condensables in the system ( air most likely). I would get a second opinion from a repuatable company, sounds like he's trying to rip you off.

Sep 25, 2012 | Bryant Heating & Cooling

1 Answer

Just fitted and smoke being emitted from top of stove house full of smoke


If this is a new furnace installation then it is normal for it to put out a large volumn of smoke. As long as this stops after a few mins. it's nothing to worry about as it is just a coating of oil they sprayed the heat exchanger with to protect it till installation.
I know the first furnace I installed thirty years ago about gave me heart failure when I turned it on and literally filled the house with smoke. Best of luck and thank you.

Jan 22, 2011 | Heating & Cooling

1 Answer

I just had a 2 stage furnace put in and a 1 stage thermostat. The thermostat has been changed three times, but the furnace still won't come on as it's programmed to do. Where do you think the problem lies?


A single stage thermostat can be used on a two stage furnace, but there is a dip switch on the furnace computer board that will need to be changed, the directions are in the installers installation guide.
Also not knowing what type and brand of thermostat you have, leaves me guessing, some higher end thermostats have intelligent recovery, if you set it to 70 degrees, at 7 AM, it will try to have the temp to 70 by 7AM, so it could be coming on, even 2 to 3 hours early, depending on the temp. Most of them have a 7 day curve, so it takes awhile for them to adjust, this feature can be turned off, you will again need the installer's install manual.
I hope this has helped, please rate me and also get back to me if you have any more questions.
Sincerely,
Paul Gibson

Apr 27, 2010 | Heating & Cooling

2 Answers

The fan motor went out and the furnace is not even 5 years old.


I have an Amana High Efficiency furnace that I purchased 5 years ago this past October (2009). My furnace started making a horrible noise last night and then stopped working. The repair person, told me my draft inducer motor needed replaced, and showed me where the plastic fan blade inside of the inducer was "chewed up." Of course my first question is, "How can a 5 year old furnace need such a costly repair already?" The only answer I received is that it will cost me close to $500.00 to have the situation remedied (service call, parts, labor). I started looking around on the internet today, and discovered that high efficiency furnace inducer motors are usually encased in plastic and the motor fan blades are made of plastic rather than metal like the lower efficiency models. Turns out that these plastic blades over time can't withstand the high heat generated and in time (they estimate 3-4 years) break. The damage to the blades causes an imbalance in the way they spin, which in turn, generates the resulting problem of a damaged draft inducer motor. Appears this is a design flaw. Yeah! I'll say. I spent $3100.00 for a brand new furnace and 5 years later I'm paying another $500.00 and apparently can look forward to doing the same in 3-5 more years! Maybe this answers in part your question?

Dec 07, 2009 | Goodman Furnace Draft Inducer Blower ...

2 Answers

The furnace wont turn on even though it says it is


not all digital thermostats are compatible with the manufacturers circuit control boards in the furnace. Hunter has had this problem several years ago. Other than that you may have miss wired the unit. usually the furnace is used as backup heat (during defrost) or emergency heat if your heat pump konks out. Are you switching to emergency heat for a furnace call?

Nov 24, 2009 | Hunter Fan Company 5/1/1 Programmable...

1 Answer

Chronotherm Three thermostat vs Buderus Logamatic Computer.


The outdoor thermostat senses the the temp of the outside air, and adjust the boiler water temp according to what it knows is best. The reason that the boiler is running longer is the old boiler used to be constantly sending 180ish degree water to the baseboard, now that water may only be 140ish degrees. The idea behind this is to reduce off cycle heat loss, as the greater the temp difference between the air temp and water temp, the quicker you loss heat. The theory in boiler run time is this, the less times it starts and stops, and the long run times will give you the best efficiency. Hope this answers you questions.

Sep 28, 2009 | Honeywell Power Humidifier: Furnace...

1 Answer

Casio G-Shock GW-300 replacement bands


I have a Casio g-shock gw-330a and now find myself again replacing the band. So far, $60 on bands. They last me two or three years. To install the band, take the band and watch to a Jeweler. My local Sears does it for me. $5 for installation; $5 for purchase shipping; $20 for band. $30 every couple of years.
This cost disturbs me.

Jun 09, 2009 | Casio G-Shock GW300CA-1V Wrist Watch

1 Answer

Thermostaat


first of all you open the hood and you can see the upper radiator hose follow that to the engine block for safety this is something you want to do when the car is cool after you follow the hose remove the screws there should be only 2 one on each side of hose and take it off the thermastat should be inside and make sure you put the new one in back the same way you took the old one out

Nov 22, 2008 | 1989 Oldsmobile Cutlass Ciera

3 Answers

Adptive intelligent recovery


On the Pro4000 model you hold the 2 arrows until you go into setup mode. Then arrow up ONLY til you get to option 13. The display will read 13 and 1, press the DOWN arrow and it will read 13 and 0. This turns off Adaptive Intelligent recovery. Now hold the 2 arrows til you see the normal display screen. You are done.

I just did this with a Honeywell tech rep on the phone.

Nov 15, 2007 | Honeywell Programmable Thermostat Heater

Not finding what you are looking for?
Heating & Cooling Logo

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honeywell Heating & Cooling Experts

Bill Long

Level 3 Expert

587 Answers

paulcarew

Level 3 Expert

2364 Answers

Brandon Berry
Brandon Berry

Level 2 Expert

407 Answers

Are you a Honeywell Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...