Question about AT&T Blackberry Curve 8300 Smartphone

1 Answer

Change Mic on BB 8310

HI, How do I chage the mic on a BB 8310. I have the new mic but I cant remive the old mic. It seems it is soldered to the mother board. Can I do it or must it be professionally returned to a repair shop?
Thanks.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 92 Answers

Sadly I would send it to a repair shop. Since it is soldered to you mainboard you run the risk of actually damaging the phone if you attempt to remove it.

Posted on Jan 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an audio technica wireless mic with the 4 pin connector. We have purchased a new lavalier mic but are still having trouble with tge mic maintaining a connection. It keeps cutting in and out if you...


Mic plug has been replaced (new lav mic) so that leaves the mic jack connected to the body transmitter. Corrosion is a possibility...

Radio Shack tuner cleaner http://www.radioshack.com/product/index.jsp?productId=12784986

but I think it's something to do with the mic jack on the transmitter. Some units solder these connectors directly to the internal PC board and after a while, the solder connections break. Have a tech open it up and closely inspect the input jack's solder pads.

Jan 28, 2013 | Audio Players & Recorders

1 Answer

RED SWR ALERT LIGHT COMES ON WHEN I KEY UP


In most cases if the mic works the common cause is the transmitter in the mother board is shorting out or not soldered to the board properly. another cause could be that your antenna is too close to the CB and will disrupt the signal.

Oct 14, 2012 | Galaxy Radios DX-959 40-Channels Base CB...

2 Answers

Nokia 3230 microphone ways problem


please give mic ways for nokia 3230

May 14, 2010 | Nokia 3230

1 Answer

Front panel Mic not working when connected to Mother Board


Yeah,sounds like the case wasn't designed for that board. Just carefully double check the pins in the manual for the board. If you don't have the manual,check the asus site.

Jul 10, 2009 | ASUS Computers & Internet

1 Answer

BB 8310 : Increase microphone sensitivity


that is not possible to my knowledge as yet but try googling it and see

May 13, 2009 | AT&T Blackberry Curve 8300 Smartphone

1 Answer

No mic on sons dslite


if you dont wanna chance soldering or anything you can buy the mic headset that goes into the headphone portal for about 5-7pound off ebay.

Mar 29, 2009 | Video Game Consoles & Games

1 Answer

No sound coming from wireless mic


check the battery, if dead replace new. check the switch might be a cold solder or loose wire and finally check the condenser mic by placing a multitester to the two connectors of the mic with one wire from the mic desoldered. if there's a continuity, then its good. if there's no continuity the mic condenser is busted. go to radioshack and find replacement mic condenser.

Mar 28, 2009 | LeadSinger LS-3222 Consumer Microphone

1 Answer

Cant talk through mic


Sounds like a bad or miswired mic. Try a new mic ( use the proper cobra mic ). If the problem still continues, check all the swiches on the front of the radio and make sure you don't have any cold solder joints ( broken lead to board connections ). Good Luck
Ed
NC Electronic
Mills, Wyoming

Dec 19, 2007 | Cobra 29 WX NW ST 40-Channels Base CB...

2 Answers

Might be mike problem(the other person can't hear me)


you need a new mircophone. if u have an old fone u can remove the mic and place it in ur nokia

Sep 24, 2006 | Nokia 3100

Not finding what you are looking for?
AT&T Blackberry Curve 8300 Smartphone Logo

Related Topics:

916 people viewed this question

Ask a Question

Usually answered in minutes!

Top AT&T Computers & Internet Experts

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18409 Answers

Are you an AT&T Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...