Samsung HCM4215W 42" Rear Projection Television Logo

Related Topics:

Anonymous Posted on Jan 16, 2009

No picture on samsung hlp5063wx/xaa

Red lights flash at bottom along with green bulk light

1 Answer

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Champion:

An expert who has answered 200 questions.

Governor:

An expert whose answer got voted for 20 times.

  • Expert 240 Answers
  • Posted on Jan 16, 2009
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Champion:

An expert who has answered 200 questions.

Governor:

An expert whose answer got voted for 20 times.

Joined: Jan 09, 2009
Answers
240
Questions
0
Helped
64928
Points
488

To test this set
unpug the 4 pin conector labeld + and _ 20v on the cg convergence module
if set turns on, the problem is that modual
repaie
replace bolth convergence IC'c stk392-040
also check all 3.9 ohm resistors and both pico fuses.
regards,
daniel.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3helpful
1answer

Samsung model hlt4675sx\xaa projection tv wont work. the stand by/temp light flashes red and the lamp light flashes green? it makes the sound that it makes when it turns on but no picture. we looked at the...

It could be the temp sensor going bad. This sensor sits on top of the metal housing which the bulb assembly slides into. The bulb assembly will have a hole on top and this is where the sensor is above. There is a small blue and white wire that plugs into it. If you pull the wire out and put a paper clip or wire in the coupling you will basically bypass the sensor connecting the blue and white wire. If your tv turns on then that is your problem. Its cheap too. Here were my symptoms..1] Turn tv on 2] Bulb would light up..(which eliminates the ballast) regular picture would show up (which eliminates the bulb and color wheel) 3] 30 seconds later tv would shut down with 3 flashing lights. After bypass the tv turned on as always and hasnt shut down yet. Always un plug tv first. Get the replacement part to avoid overheating and possible fire
0helpful
1answer

Samsung hlt5075sx/xaa no noise or picture The green light on front flashes 18 times then red flashes once goes through this three times then all three flash then center green comes on constant after that...

That model seems to have had a problem past and I would contact Samsung or a service engineer as it sounds in need of a repair to my mind.

Hope this helps........
0helpful
1answer

Samsung DLP hlp5063wx/xaa - Cycles through the warm up 2 times but does not turn on, then 3 lights flash on the front (2 green, 1 red) Bulb is new and looks good, fans seem to be spinning freely. Any...

If your having the "3 light" problem it could be an indication of a bad lamp however if there is a buzzing or a grinding sound it could be one of two moving parts. The color wheel or the cooling fan. I would go the cheaper route and replace the color wheel first since you say the fan is spinning. The thing is the lamp will not turn on if there is a problem with one of the other two parts. The motor on the cooling fan is too small for such a big fan so I would definately try it next. It's a big problem with the DLP tvs. good luck!
1helpful
1answer

Our Samsung Model HLP5063WX/XAA - dark images

I suspect that you may need to replace the ballast for the lamp and the power supply board.
7helpful
2answers
Not finding what you are looking for?

378 views

Ask a Question

Usually answered in minutes!

Top Samsung Televison & Video Experts

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

 Grubhead
Grubhead

Level 3 Expert

5755 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Are you a Samsung Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...