Question about Miele Novotronic T230C Electric Dryer

1 Answer

I need an instruction manual for the T230C

I am trying to establish the correct procedure for cleaning the filters and condenser unit in this tumble dryer in order to provide training for our staff as at present we are constantly having problems with this dryer due to not cleaning properly

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 70 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I reduce the humidity of the air expelled from the dryer?


If the aire being expelled is humid then this suggests that the unit if working fine. if clothes are still damp then maybe give them a second spin before putting in the drier, or dry them for longer. Also try putting less in the drier and drying in two loads.

Oct 19, 2014 | Miele Novotronic T230C Electric Dryer

3 Answers

The tumble dryer bip and flash "empty water" even if no water. I have cleaned every filter (2 inside the big filter at the bottom of the tumble dryer) but still have the trouble


Hi,

I want to first make sure that your dryer is serviced up. so i want you to do these steps.
Most of the problems will be resolved doing these......

As clothes are tumble dried, they drop fibres. Most of this fluff is trapped by the lint filter and this needs to be checked and cleaned regularly. Lint also builds up in the vent pipe and around the electric motor in the rear of the dryer.

1.clean lint filter
989c696.jpg
Wait until the dryer cools, open the door and lift out the lint filter.
Gently brush off lint using your fingers.
On many models, the filter may also be washed. Check your manual for instructions.
If the filter is damaged in any way, you should replace it.

2.Vacuum area where lint filter sits:

The area where the lint filter sits should be vacuumed .
Remove the lint filter, and use a narrow vacuum nozzle to remove dust and lint from the fitting.

3.Clean inside the tumble dryer:
8dc9315.jpg


2210c2c.jpg
1. Make sure the dryer is cool, switch it off and unplug it.
2. Unscrew the retaining screws on the back panel, and lift it off. Vacuum the blower area.
3. Also vacuum around the vent pipe connection.
4. Replace the back panel and refit all the screws.


4.Check tumble dryer vent hose:
8d2299a.jpgWait for the dryer to cool. Unplug the vent hose and inspect its entire length for snags in the pipe.
Make sure the vent is not obstructed on the outside wall, and fit a flap or screen to keep out small animals.
If your vent pipe is punctured or damaged, you should replace it.



To avoid dryer problems,
Make sure the dryer is level and does not rock, and consult the manufacturer's instructions for the maximum weight of clothing to dry at one time. Also, make sure clothes have been spun-dry before putting them into the dryer.

This is just initial help,
Post your comments about how things turned up, Ill be giving suggestions based on your reply........

Thanx for using fixya,
Cheers.

Sep 27, 2008 | LG Dryers

1 Answer

Not heating


If you can hear the dryer start and operate but at end of cycle your clothes are wet then it is likely (assuming the heater is turning on) that the fluff collection on the condensor unit is blocking its operation.
Refer manual at this site and follow instructions on page 20.

http://www.eirvik.is/gogn/L/t233c.pdf

Apr 19, 2014 | Miele Novotronic T230C Electric Dryer

1 Answer

Clean filter


If this is a condenser dryer, it could be the condenser unit that needs cleaning

Dec 21, 2013 | Siemens Dryers

1 Answer

I need to clean my filter on my beko tumble dryer!


I usually just stick the shower on it to clean out all the bits of fluff that gets gathered in there, but remember to give the inside of that hatch u brought it out of with some kitchen towel before u put the condenser filter back in.

Feb 23, 2010 | Dryers

2 Answers

How to clean a whirlpool awz7913 condenser tumble dryer heat exchanger


how do i clean my heat exchanger on the whirlpool awz 7913 condenser tumble dryer?

Jan 19, 2010 | Whirlpool Dryers

1 Answer

Miele T230C do no start


If start LED does not blink, most likely fault is your door lock.

Jan 04, 2010 | Miele Novotronic T230C Electric Dryer

1 Answer

I have a Bosch Maxx condenser tumble dryer that wont work.


Have you taken the condenser itself out from the bottom of the machine? Remove the condenser from the bottom door and rotate the clamp tags which secure it in. Slide condenser out (aluminium mutli-finned box assembly) and carefully take it outside. Use a garden hose with lots of water pressure to spray each vent passage carefully to clear lint and dust away. Passages must be cleared in both directions, long ways and cross ways. Cross ways is the problem area and once you finish clearing the air ways you should see daylight through the condenser easily. Reassemble and always clear lint filter in the door /drum area.
Good luck.
Sam

Sep 02, 2009 | Bosch Dryers

Not finding what you are looking for?
Miele Novotronic T230C Electric Dryer Logo

432 people viewed this question

Ask a Question

Usually answered in minutes!

Top Miele Dryers Experts

Tim Whalen

Level 3 Expert

3056 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Mike

Level 3 Expert

4331 Answers

Are you a Miele Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...