Question about Office Equipment & Supplies

1 Answer

Exposoure lamp glowing while standby mode in sharp AR M201 copier

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 267 Answers

BAD CONTROL BOARD nothing else can do this

Posted on Jan 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Why ar m201 sharp copier shows error h2 00


it means that the thermistor in the fusing unit is open

which could indicate that it may have become faulty or is because of power fluctuations, a simple crop 14 reset should remove the error, but if it returns it should be looked at by a qualified sharp technichian

Jun 11, 2014 | Sharp AR-5320 Black and White Copier

1 Answer

Ar m201 error h2 00


thermistor open , check thermistor , might have to replace

Jun 11, 2014 | Sharp AR-5320 Black and White Copier

1 Answer

System error (f2-04) for Sharp Copier, model AR-M201


It is copy lamp error.
1- check the copy lamp on with sim.
2- replace the power unit.
3- replace the inverter.
4- replace the mcu pwb.

Jul 01, 2012 | Sharp Office Equipment & Supplies

3 Answers

I am using Sharp AR-M201 photo copier machine. I just came across a error message ` System Error F2-02 Refer to user guide' Can anyone guide me to solve this problem? Thanks K K Mendon


F2 -02 Toner supply failure
cause :-
- developer unit trouble

- Toner supply abnormality caused by
installation of unpacked toner cartridge

Dec 26, 2010 | Sharp AR-M205 Copier

2 Answers

Sharp ar-m236 error code H4-21


-H4-21 means: Sub heater lamp abnormally low temperature detection. The setup temperature (about –25°C: Sim 43-1-1) is not reached within the specified time (about 32sec) from turning on the power ON SW. (When the temperature falls below 140°C in the standby mode.)

-Causes:
Sub heater thermistor defect
Sub heater lamp failure
Sub thermostat failure
Control PWB failure
-Check the sub heater lamp blinking with SIM 5-2-2.
When the lamp blinks normally: Check the thermistor and the harness. Check the MCU PWB thermistor input circuit.
When the lamp does not light: Check for disconnection of the heater lamp and thermostat. Check the interlock switch.Check the power PWB and the MCU PWB lamp control circuit.
Clear the display of self-diagnostics with SIM 14.
The H4 errors will not reset by themselves. You must enter service mode to reset this error even if the problem has been repaired. The reset process is outlined below (DO NOT USE ANY OTHER FUNCTIONS IN SERVICE MODE):
Press the following sequence: "#/P" "*" "C" "*"
Type in 1 4
Press start
hit 1 for yes
hit start
Unit should power off and the restart.

This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya


Dec 28, 2009 | Sharp AR-M237 Digital Copier

2 Answers

Sharp AR-M201


no. i cant print. its showing red light and user guide attention

Jan 14, 2009 | Sharp AR-5316 Advanced Digital Imager...

1 Answer

Sharp copier have complaint


lamp on all the time is normal operation. It makes sure the copys come out quickly and keeps machine at ready.

Jan 13, 2009 | Office Equipment & Supplies

1 Answer

Sharp copier have complaint


it is the problem laser unite or drum image

Jan 13, 2009 | HP PhotoSmart C4180 All-in-One Color...

2 Answers

H4 flashing


to access the service mode.
enter the folowning keys .PROGRAM .ITEREPT .CLEAR INTERPT MUST BE IN SEQUENCE
THAT ENTER NUMBER 14 THAT START BOTTON
HOPE THAT HELP

Nov 14, 2008 | Sharp AR-M205 Copier

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

kakima

Level 3 Expert

101406 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

67757 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...