Question about Kenmore 75002 / 75004 Gas Kitchen Range

1 Answer

CONTROL PANEL MY CONTROL PANEL IS DISPLAYING E3 - F1 - AND BEEPS HOW DO I FIX THAT AND WHAT'S THE PROBLEM.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 35 Answers

You are having a problem with your electronic control panel.to solve this problem you have to replace electronic control board and touchpad assembly.

Posted on Jun 30, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fix f5 e 1


F1 - E0 EEPROM communication error 1. Disconnect power for at least 30 seconds.
2. Re-apply power and observe for at least one minute.
3. If code re-appears, replace control board (also called ERC or clock).

Note: Applies to all F1-E... codes except F1-E3. F1 - E1 EEPROM checksum error F1 - E2 UL A/D error(s) F1 - E4 Model ID error F1 - E5 Calibration shifted F1 - E6 Latch signal mismatch error F1 - E9 Stack overflow F1 - E3 Wiring harness cavity size does not match previously stored value The "Cavity Size Select" jumpers in the wiring harness indicate a cavity size different from that which the control was previously configured for. Check the jumpers in the harness to make sure they agree with the actual oven size.

Jun 05, 2015 | KitchenAid Architect II Superba EQ Series...

1 Answer

Whirlpool wall mount oven won't heat at all. Error code E3 F1


Technical sheet says all F1 codes to replace control

Jan 17, 2014 | Whirlpool Ovens

1 Answer

Error E# and F1


Hello,the error codes E3 and F1 means Wiring harness cavity size does not match previous stored valued
SOLUTION:The "Cavity Size Select"jumpers in the wiring harness indicate a cavity size different from that which the control was previously configured for.
Check the jumpers in the harness to make sure they agree with the actual oven size.
Thanks



Jun 01, 2010 | Whirlpool RBS245PDS Electric Single Oven

1 Answer

F1 in F&P 2 drawer dishwasher


You will need to be a bit more specific when you say "no flood".

Are you having this F1 fault in one or both drawers?

What did the engineer do when he was there last time?

Does the F1 code flash with beeps?

What happens when you turn the mains power off and on after a short delay?

Please provide the actual model number of your fisher and paykel 2 drawer dishwasher.

May 19, 2010 | Fisher and Paykel Dishwashers

1 Answer

Warning codes f2 & e3 on Whirlpool oven . Warning beeps alerted us to a problem.


Remove the power from the oven. Open the control panel and unplug the key pad ribbon from the control board. Assemble the control panel back and turn the power on. Wait a few hours.
If the error code came back on, replace the control board.
If the error code did not show up, replace the control panel (the key pad comes as a control panel assembly).
good luck

Feb 27, 2010 | Whirlpool Ovens

3 Answers

KitchenAid KESS907 Electric Range E1 F1 Error Code


F1 E1, replace Electronic Range Control.

In other words, the controller board has failed.

Jan 29, 2009 | KitchenAid KDRS807SSS Dual Fuel (Electric...

1 Answer

Error Code F1:E3


reprogram the control board as following:press buttons on range
power off wait 5 sec
power on wait 5 sec
convection broil
clean
backed goods
stop time
190
timer set
start button 12 times(it will go through all the settings)

Mar 17, 2008 | KitchenAid KESC307 Electric Kitchen Range

1 Answer

F1:E3 KGST307 free standing stove


there is no way to reset the control. you have to replace it. sounds the the jumpers on the board have failed.

Dec 22, 2007 | KitchenAid KGST307 Gas Kitchen Range

3 Answers

Kenmore, F1


I really need to know the make and model but most F1 are a bad control board.. F1 Analog to Digital Failure Disconnect from power for 30 seconds - if display reappears - replace control board

Aug 27, 2007 | Ovens

Not finding what you are looking for?
Kenmore 75002 / 75004 Gas Kitchen Range Logo

Related Topics:

201 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Kitchen Ranges Experts

Cindy Wells

Level 3 Expert

5577 Answers

Sal De

Level 3 Expert

2699 Answers

Justin Duby
Justin Duby

Level 2 Expert

370 Answers

Are you a Kenmore Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...