Question about Jet Tech Systems 24 in. 737 Free-standing Dishwasher

1 Answer

Dishwasher will not stop washing

The 737 Jet Tech will not stop washing or drain. You have to open the door and get wet to stop it, then use the white drain button to let all the water out. When you try to close the door to allow the unit to heat up, it automatically begins to wash again........

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 5 Answers

The problem is the pressostat which is part of the water level system. Either the pressostat needs adjustment or replacement. the air trap at the back of the unit in the sump area may be loose or broken, this should be inspected. refer to http://www.mvpgroupcorp.com/jettech/737_exp_view.pdf .

Posted on Mar 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After 20 mins water temp still not at 150 on my jet-tech 737 dushwasher.


The reason the temperature are going up is the heating system is defective. The thermostat on the booster (rinse) is not satisfied. First thing to verify is the contactor that is activated by the rinse thermostat. Often one of the wires on the contactor will burn.

Nov 20, 2013 | Jet Tech Systems 24 in. 737 Free-standing...

1 Answer

Not heating up to temp of 150 for wash cycle


The 737, like most Jet=Tech models, requires to be drain empty at least once a day. If the unit is empty and it is started, it will take approximately 30 minutes for the machine to be ready. Which means, the unit will fill and then heat up both booster tank first and then wash tank. If after all that the wash temperature is not up to 150f then the wash thermostat needs to be either calibrated or replaced if the wash element is in good condition. It is assumed here that the booster temperature is reaching 180F.
Search by part number or description Search by part number or description

Nov 20, 2013 | Jet Tech Systems 24 in. 737 Free-standing...

1 Answer

Jet tec f18 water goes to 120f redy light does not come on will not wash got hot water to 120f open door have steem but no wash frank


Verify the contactor for working condition. maybe burned wires or bad contactor. if it is good then the rinse thermostat or, less likely, the booster element.

Oct 07, 2013 | Jet Tech Systems 24 in. F18DP...

2 Answers

The drum stopped spinning, but could still hera motor running. The door was locked; could not unlock to open. After several attempts of unplugging/replugging door could be open.


Is this a dishwasher or a washing machine that you have a problem with.

The drum is usually in a washing machine. The motor you hear running is the drain motor. So this is a normal operation of front loading washing machines. When the drum stops spinning, the drain pump takes away the remaining water and then a timer lock comes into play to make sure the clothes are settled dowm before you can open the door.

So I do not see there is any problem. Please accept the solution if ok else post a comment to confirm the exact problem with your appliance.

Mar 21, 2011 | Dishwashers

2 Answers

Not Drying


I found that if the rinse agent (Jet Blue) has run out the dishes stay wet.

Aug 21, 2008 | Bosch SHU3305 Dishwasher

1 Answer

Water to dishwasher not hot enough


The 737 model could run on even lower temperature (80F). Given time, the unit will heat up the water. the trick is to give it time.

That model is made for commercial use, not really for residential. It will not fully drain every cycles. The important thing to keep in mind is to empty the dishwasher (turn it off, pull the stand-pipe out, and drain) every night and left empty. When you want to use the unit, put the plug back in and turn it on, wait 20 to 30 minutes and it should be ready.

Robert Marsolais

Jul 28, 2008 | Jet Tech Systems 24 in. 737 Free-standing...

2 Answers

Bosch Dishwaher shy56a


Bosch dishwashers have a seperate pump for washing and another for draining. Try making it fill more than once. There is usually a timed fill and the float stops it before it overfills It also might prevent it from washing without enouth water Try defeating the door switch and play with the float during fill. There may be a sensor that won't let it go into wash. Be prepared to get a little wet if it should start up suddenly. A slightly safer way is to fill it with the sprayer from the sink. and see if it will go into wash.

May 08, 2008 | Bosch 24 in. SHY56A05 Stainless Steel...

1 Answer

Jet tech washer 737 dp


Ouch.

Before you start changing all sort of parts, correct your problem with the wires. You may have to change most of them, depending on how bad the chemical burned tru them.

A good cleaning is required because that soap is going to continue chewing on those wires.

You're right about a short causing other component failure. But first repair those wires

Robert Marsolais

Dec 19, 2007 | Jet Tech Systems 24 in. 737 Free-standing...

Not finding what you are looking for?
Jet Tech Systems 24 in. 737 Free-standing Dishwasher Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jet Tech Systems Dishwashers Experts

 Robert Marsolais
Robert Marsolais

Level 1 Expert

25 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Brad Brown

Level 3 Expert

13576 Answers

Are you a Jet Tech Systems Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...