Question about Kenmore 3.8 cu. ft. HE3 Front Load Washer

1 Answer

\ capasithy wahser plus 2 has f-   21 flashing and other ind\

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 5,911 Answers

"F21" is a Long Drain error. The following link explains:

http://www.fixya.com/support/r1484065-f21_error_code_whirlpool_duet_kenmore

Usually, a good cleaning of the drain pump reservoir is all that it needed to correct this problem. Don't forget to check all the drain lines as well. If you have questions, or if the error code does not go away following cleaning, please let me know before you rate the solution, so that I may assist you further. I hope this helps you.

Posted on Jan 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Indesit IWC6105 Keeps filling with water and lights flashing


Almost certain to be a power pcb failure due to the fact it fills and drains at the same time this is a regular fault symptom on indesit laundry appliances. Word of caution tho inde pcb's are generic to a range and the software must be programmed via a lap top to your specific appliance so you can't just order a pcb and pop it in sorry

Dec 08, 2013 | Indesit Washing Machines

1 Answer

My Fisher & Paykel GWL11 top load wahser will only wash in cold after the first cycle. It


the problem other then the thermosat and solenoid valves is probably the main board. to check you need to replace the board with known good second hand board . buy an old machine for parts

Nov 19, 2011 | Fisher and Paykel GWL11 Top Load Washer

2 Answers

Water is filling the tub when not in use


One of the water inlet solenoid valves is faulty -- it's not closting when the "water-fill" function is off. The solenoid valves are the parts the hoses on the back of the wahser are connected to. There are two -- hot and cold.

Cleaning them and replacing wahsers / O-rings / gaskets may solve the problem or may need to be replaced. More info, let me know.

Charlie

Feb 12, 2011 | Maytag Neptune Washer

1 Answer

It is only doing half a wash and then flashes up code OE i have misplaced the booklet to see what the problem is,i would be greatful if you coild help me please.


Overfill error the washer's water level sensor took longer than expected to verify water level. Remove the water, ind the water level pressure tube and blow out the sediment in the base of washer. re-secure and retry.

Jan 26, 2010 | Washing Machines

1 Answer

Wahser stopped after wash cycle, burning smell


Hi, it is possible that something got into the pump and stopped it from turning. Let the drain hose down so that it drains into a bucket or a floor drain if possible.
If water does not drain then it is deffinetly plugged. Once you get the water out of the washer, tip it against the wall and try to remove the pump off the motor. There are two clips that hold the pump on. You will also need to remove the hoses.
With the pump off, you can set the washer back down and try to run the spin cycle. If the motor runs, it must be the pump.
Please let me know if I can assist you further.
Thanks
Vic

May 23, 2009 | Roper RAS6233KQ Top Load Washer

2 Answers

Whirlpool Lsq8243h


unplug washer and lean washer back aganst wall,put something under frount of washer.So you can see under washer .Look and see if the belt are still on the pully or if there streached out (not tight) fix accordingly.

Jan 17, 2009 | Whirlpool LSQ8243H

1 Answer

Maytag frontload washing machine keeps turning off and displaying error 3


My wahser machine keeps turning off becuase the knob is not tight and the knob slowly moves to the off position. How can I get this fixed?

Apr 12, 2008 | Maytag Washing Machines

1 Answer

Lift aggatator out of sears wahser model 110-25862400


see if the srew has loosend up from the transmission shaft

Mar 05, 2008 | Kenmore 24032\24036 Top Load Washer

1 Answer

My dryer/wahser


possible lid switch or internal fuse. Regards Engineer

Dec 30, 2006 | Kenmore 98702 Stacked Washer/Dryer

Not finding what you are looking for?
Kenmore 3.8 cu. ft. HE3 Front Load Washer Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Fred Sops

Level 2 Expert

271 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...