Question about Computers & Internet

1 Answer

Monitor turns off/countinually beep sound

Hi guys!

For some unknown reason and maybe twice a week my monitor turns off by itself and I get a continually beep sound when I turn on my computer after this.
Then I unplug my monitor from the back of my computer for a minute reconnect it again, restart my computer and everything is just fine.

I thought it was my Hpw2207 monitor but after I had it replaced I noticed the same problem, I also tested another monitor and got the same issue. My computer is a ''built-in comp'', but I never had this problem before.
Could you please help me find an answer???.. thank you guys!!!


Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,913 Answers

Reconnect your ram on mother bord after clean dust from all circuit.

Posted on Jan 15, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

No display on monitor,No cd drive ejecting but cpu fan is running and power on led light is in green in mother board ,No beep sounds Can anybody Know the problem of my motherboard? Help me guys

This is a difficult one without knowledge of specifics. However here goes. The absence of beep codes would indicate that the motherboard is getting through its POST routine OK, although some boards give a single beep when the POST is completed and the absence of this beep indicates a problem on these boards.
The CD drive not ejecting can be that there is no power to it. Does it have a light on it during POST. If so it is probably just stuck. Try using a straightened paperclip in the very small hole in the fascia plate.
Now to graphics, I am sure you have checked that the computer to monitor cable is firmly connected at both ends, and if the computer has two graphics ports, that it is plugged into the correct one. Does your graphic card have a separate power supply, if so is this securely seated? The way to test the graphics is to connect another monitor that is known to work into the computer and seeing if you get a picture. If you do then the monitor you are using is faulty.
Hope this is helpful, if so would you please register that with Fixya

Dec 17, 2014 | Computers & Internet


No sound after rebuild

Hi guys

I'm having trouble getting sound from my A7V8X-MX motherboard. I've just rebuilt my machine using WindowsXP professional and for some reason ther is now no sound coming from my p.c. All connections are intact. I don't know if I need an audio driver or if I need to update my bios. Please help it's really getting annoying now, it's been more than a week and I'm lost without the sound.

on Aug 16, 2008 | ASUS A7V8X-MX SE Motherboard

2 Answers

Sir,when i turned on my system nothing displaying on my monitor,i can hear a beep sound.wat problem is this?

Hi,the beeping could be as a result of a faulty or slightly shifted Memory,or Display cable not properly connected,so check and let me know how many times it beeps.thanks

Jan 07, 2011 | Intel Motherboard

1 Answer

Hi i ive got a pc with msi ms7312 motherboard ,unknown what procesor but for sum reason when turned on my monitor wont *** on ,it has on bourd grafix ,iv tried the monitor on the pc im using now and it...

It's an very old Athlon XP processor. But the problem isn't with it, it's with the motherboard itself, the chipset has died.
There is nothing you can do, it's dead for good. Replace it - any Socket A motherboard with DDR memory will do.

Oct 18, 2010 | MSI KM4M-V Motherboard

1 Answer

"no signal" on monitor, my cpu fan is working fine but beep sound is not coming

Try this steps:-
1.Please check your power cables properly.
2.Remove the monitor cable from CPU and turn on the monitor and see are you getting the dispaly or not.

Oct 04, 2010 | Intel Motherboard

1 Answer

Motherboard beeps

kindly replace the ram and reset the bios setting set it to default.

Jan 14, 2010 | Asrock 775i65GV Motherboard

1 Answer

Motherboard beep code 1-2-1. System timer error?

1-2-1 You have a bad timer chip on the motherboard. You need a new motherboard.

Sep 24, 2009 | Mercury KVM266PM-U (KVM266PMUD1600)...

1 Answer

No Signal To my Monitor and no beep.

First refix the RAM and Pci graphic card.
Pull cmos cell from mother bord for 15 minutes then put again into its position then all settings are defaults.
Then if still face problem then check with other RAM.

Aug 13, 2009 | Computers & Internet

1 Answer

Continous Beeping sound

Hi neosw,

Could you provide a little more detail?

Was this a previously working set-up or is this a new build?

If this was a previously working set-up have you changed anything?

When you switch on the PC
  • do you see anything on the screen, does the monitor remain in standby?
  • are any of the fans running?
  • does the hard drive spin up?
  • does the beeping sound stop after a short while?
The reason I ask these questions is because a continues beeping usually means that the BIOS is not seeing the processor, or that the power to the processor is not correct. With some BIOS manufactures it can also mean the processor clock speed is not set

Please don't take this the wrong way but...if you provide greater detail in your question, the easier it for us to diagnose your problem, otherwise we can only make educated guesses.

I hope this has been of some help.


Spare head 2

Jan 06, 2008 | Soltek SL-K8AN2E (SL-K8AN2E-GR)...

2 Answers

Syntax motherboar error beep code

you may need to reset the cmos on jbat1 terminal with the jumper across pins 2-3 then back to pins 1-2, then boot up and reset time,date and hdd, press f10 to save and exit. this is all assuming your board supports the sempron processor as well as the athlon

Mar 26, 2007 | Syntax SV266AD Motherboard

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

383 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers


Level 3 Expert

98879 Answers

David Payne
David Payne

Level 3 Expert

14089 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides