Question about Mitsubishi WS-55809 55" Rear Projection Television

1 Answer

When I turn the TV on it turns itself off

We are hooked up to Verizon Fios. All of our other TV's are hooked up to Verizon Fios, and we are not having the problem with them.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 90 Answers

If you hold the menu and input buttons on the front of the tv down at the same time for approx. 5-10 seconds, the tv will give a blink code. It will blink some # of times...pause and then repeat. This will tell a servicer why the set is going into shutdown. Repairing the problem will most likely have to be dont by a professional.(unless you are very mechanical and have good soldering skills)

Posted on Jan 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tv goes off, then comes on, and volume goes to max


OMG! Verizon Fios at it again with changing boxes! Well let me tell you if you do not loose signal on a DVD using these same inputs ITS NOT YOUR TV!

Whats going on is further into Verizon system you loosing the signal from the VDSL slam outside in the pill box. This thing will need to be replaced and they are going to blame your TV until you just give up and buy a new TV only to figure out its not your TV.

1. Call them back
2. tell them to check there network
3. if that dont work tell them to check it again
4. if you have HDMI use that instead of the scart connections.

I hope you have luck with Verizon Fios there internet rules but there TV service is sub par!

Thanks
rulds2008

Jul 17, 2009 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

I have a 50 inch Pro Scan Projection TV that was bought in 1995. I was just watching tv yesterday, everything was fine. All of a sudden when I changed the channel the picture became blurry like it had a...


If this set is a PTK169 chassis, you could have bad tuning capacitors in the horizontal for the Horizontal yoke return and pincushion circuit. I would suggest that only a professional diagnose and repair it due to the circuit it is.
Hope this helps,
Skyassoc

Jun 20, 2009 | Projection Televisions

1 Answer

Philips 50" flat screen - Closed captioning won't turn off


on my magnavox it was the verizon fios remote that enabled it by accident (it is tuned to control the tv) however it was a cc button represented by the * on the remote that i had to select to change the cc. this didn't make it go away so i just pressed buttons i used the "Aspect" button represented by the # it changed the ratio and the message went away. I usually only use the fios remote to turn the tv on and off but this must be some whacky override that comes from the fios remote.

Jan 27, 2009 | Philips Magnavox 50ML8105D 50" HDTV DLP TV

1 Answer

OVERHEATED?


yes open it up get dust out run small fans in nit see how long it stays on

Sep 15, 2008 | RCA HD52W56 52" Rear Projection HDTV

1 Answer

Do we have to manually set the pix set key for every station/show we watch? We loose scrolling writing at the top and bottom of the screen on my dad's new 32" lcd tv bought at Wal-mart. When we set...


Thanks for the offer but we cannot afford to pay additional money for something the Factory support service Should provide.

From what we have heard through the Verizon installer, our SANYO LCD TV probably does NOT have a Automatic picture adjust system. That would most likely be the reason for the maunual button on the remote control. The troublle is that with the FIOS service, you do NOT use the TV's remote control. That leaves to switching back and forth between two different remotes wiich can be vary confusing for someone that is not 88 years old.

It is bad enough that you have to remember which channels you have to go to to receive HD programming signals. If I were making a TV set, and or running a TV network/ cable service, I would transmit both HD and regular signals on the same channel number and let the TV and or the decoder box figure out if my set could display High Definition. Isn't that what we spend lots of money buying equipment and paying each month for service?

If anyone out there knows if the SANYO 32 inch LCD TV sold at Wal-Mart automatically adjust to the picute format, (PIX 1-4) we sure ould like to hear from you.

Jul 23, 2008 | Projection Televisions

1 Answer

I have an RCA HD TV model 61LPW42 - it was working fine until we moved from NY to MD three days ago. Verizon FIOS came and hooked it up and wow is the picture great. But we can't get any sound. We...


no one ever got back to me - no email, no chat, no nothin
so.... does that mean I will also get no response next month when I contact you to have the charge I'm sure I'll see on my card next month removed?

Jul 06, 2008 | Projection Televisions

1 Answer

Vertical rolling on Hitachi 60SBX78B


It ended up being the Verizon Fios box. We recycled it and the picture stopped rolling. Thank you for being here to help. If I have any future questions, I'll definitely use your site.

Mar 07, 2008 | Hitachi 60SBX78B 60" Rear Projection...

Not finding what you are looking for?
Mitsubishi WS-55809 55" Rear Projection Television Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1191 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

68323 Answers

Are you a Mitsubishi Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...