Question about Hotpoint 24 in. FDW60 Free-standing Dishwasher

Open Question

Fault code hotpoint dwf70 dishwasher has a recuring fault code al99 , what dose this mean. thx kev

Posted by on

5 Suggested Answers

Joe_Rex
  • 114 Answers

SOURCE: dishwasher dose not drane

YOU CAN TRY REMOVING THE LOWER RACK AND LIFT OFF THE SPRAYER. THE DRAINAGE WHOLE IS USUALLY VISABLE. YOU CAN FLUSH OUT THE DRAIN TO SEE IF THAT DOES IT. THERE SHOULD BE NO STANDING WATER IN THE BOTTOM OF YOUR DISH WASHER AFTER WASH CYCLE AND DRY CYCLE. HOPE I COULD HELP.

Posted on May 02, 2007

  • 19 Answers

SOURCE: Hotpoint Ultima dishwasher dwf70

Press and hold the start and the on/off buttons together. It should come out of demo mode.

Posted on Aug 26, 2007

  • 1 Answer

SOURCE: Hotpoint FDW 85 Dishwasher

You just need to switch the machine off for approx 30 seconds from the mains and switch it back on again!!

AL99 means that there is a communication error within the machines software.

Posted on Jun 16, 2008

  • 93 Answers

SOURCE: what does code al99 mean

AL99 is a communications error.
check PCB(s) cabling, connectors .

Posted on Jul 28, 2008

  • 1 Answer

SOURCE: I have a Hotpoint Ultimo Dishwasher FW80 and the

I am sorry but your response time was too slow. I will not be taking you up on your offer of the assistance plan

Posted on Feb 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an hotpoint sdw60 dish washer that is flashing 2 yellow lights, these are numbers 5 and 7 (fast and dry 40c) and (delicate 50c) can anybody tell me what this means.thankyou


Hotpoint Indesit dishwasher flashing lights fault error codes ...

? 15:08
www.youtube.com/watch?v=FRLbrBPHcnE
May 3, 2015 - Uploaded by how-2-repair.com
http://www.how-to-repair.com/help/hotpoint-aquarius-fdm-dishwasher-flashing-lights-and-there-fault-codes ...

Oct 02, 2015 | Hotpoint Dishwashers

1 Answer

Hi I have a Hotpoint fdw80 witch is displaying an error code AL10. Please can you tell me what this means so I can decide a course of action. Many Thank's Amanda


I found these error codes for the hotpoint fdw80

AL01 - Anti flood switch operated
AL02 - Valve or connections
AL03 - Time out - drain
AL04 - Thermistor (module)
AL05 - Circulation pump
AL06 - Time out - fill
AL07 - Not used
AL08 - Time out - heat
AL09 - Software recogntion error
AL10 - Heating circuit
AL99 - Communications error - connectors, cables etc.
H20 - Time out - fill (taps)

Now looking at AL10 error. Most often it is the heater element which is not effective due to scale formation. Make a solution of white vinegar and water (50:50) pour it onto the base of the dishwasher. Leave overnight and run dishwasher as normal. Somehow the vineger has to reach the heating element which is an inline heater. I am assuming normally you would use the hotwater connection from the kitchen tap.

If this does not help - depends how soon into the cycle you get the error you will have to replace the heater. I think it would look like this.

Feb 01, 2011 | Dishwashers

1 Answer

I have a Hotpoint Ultimo Dishwasher FW80 and the display is showing AL99 But the machine is still working. It has been operating for around 20 minutes


I am sorry but your response time was too slow. I will not be taking you up on your offer of the assistance plan

Feb 08, 2010 | Hotpoint Dishwashers

2 Answers

Hotpoint Dishwasher BF1620 blew the main fuse circuit in fuse box during mid cycle wash? Re-set main power fuse circuit but now as soon as Dishwasher switched on immediately blows main kitchen power fuse...


This is happening because you have a very bad fault, a Phase to Earth short, problem. Leave machine UNPLUGGED, Breaker/Fuses OUT. do NOT use it, nor Touch it, It is possible to get severe electric shock. PLEASE get a registered serviceman to inspect this unit.

Feb 07, 2010 | Hotpoint 23 in. BFI62 Built-in Dishwasher

1 Answer

What does code al99 mean on hotpoint ultima dishwasher


AL99 is a communications error.
check PCB(s) cabling, connectors .

Jul 27, 2008 | Hotpoint Dishwashers

1 Answer

60cm Ultima DWF70 Free Standing


Hotpoint code A03 is a short circuit on the temperature thermistor.

This will need replacing, or there is a fault with the supply wires leading to it.

This should be replaced.

Do you need instructions or the number of an engineer?

If you do, please contact again, otherwise please rate as Fixya! if this has resolved your problem.

Thank you.

Jun 15, 2008 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

Hotpoint FDW 85 Dishwasher


You just need to switch the machine off for approx 30 seconds from the mains and switch it back on again!!

AL99 means that there is a communication error within the machines software.

Jun 15, 2008 | Hotpoint 24 in. FDW60 Free-standing...

2 Answers

Hotpoint


hope this helps u... all the error codes and faults, they can be found here>>>>>>> http://www.hotpointservice.co.uk/hs/pages/content.do?keys=FAQ:ERROR_CODES

please vote thankyou

Apr 04, 2008 | Hotpoint 24 in. FDW60 Free-standing...

2 Answers

Hotpoint Ultima dishwasher dwf70


Press and hold the start and the on/off buttons together. It should come out of demo mode.

Aug 25, 2007 | Hotpoint 24 in. FDW60 Free-standing...

Not finding what you are looking for?
Hotpoint 24 in. FDW60 Free-standing Dishwasher Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

bosch5

Level 2 Expert

157 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Hotpoint Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...