Question about HP Deskjet 5940 Photo InkJet Printer

2 Answers

Can't find ink levels for my HP Deskjet 5940

How do I get to the information about ink levels on my HP Deskjet 5940?

Posted by on

  • Anonymous Mar 14, 2014

    reset 1050 deskjet ink level

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 140 Answers

The installation disk for your printer has a setup wizard that monitors your ink levels in your printer. Go through the installation again as it will not hurt anything and you should find it on one of your pop up screens that it leads you to.

Posted on Jan 14, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Go to print - then to properties - then services- click service this device - click ink levels.

But it will only show you the ink levels if you are using genuine HP catridges - otherwise it
shows empty.

Hope this helps

Posted on Jan 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A printer,s ink pad is at the end of its service life


This means the waste ink collection sponge is full. This counter can be reset but it is strongly recommended to replace the ink pad as you will end up with a large amount of ink spilt on your desk if you continue to use the printer after the pads lifespan. It can be quite a large job to change depending on the model. If the printer is not an expensive model it may be more cost effective and less messy to simply replace it with a similar model.

Jan 14, 2017 | The Office Equipment & Supplies

1 Answer

5C00 Error Code as well as yellow and green alternating lights


To fix this error is much easier than it looks. Unplug the printer power. Move the ink cartridge cradle to the left. Over to the right you will see a small pad about 1cm square. This pad and the area around should be covered with ink. Get a cloth and press down on this pad - it's not fixed so should come away with the cloth, otherwise use tweezers gently. Squeeze the pad several times between your thumb and forefinger while inside the microfibre cloth to remove ink build up. Then when not much ink comes out on the cloth, clean the area in the printer around the pad so that looks free from ink too. Then position the pad back in place, move the cradle back into position, plug in and switch on - should work fine now.

Jan 14, 2017 | Office Equipment & Supplies

3 Answers

My Epson WF-3640 is printing with gaps in the text. How do I fix this issue?


Make sure you should remove shipping tape from the ink cartridge. These taps are used to protect printer during shipping but you have to remove it before starting printing. Beacuse these taps prevent the ink to entering in print head. If you will not found shipping tape in your printer then there is terr off strip, remove it. The tear off strip seals the the vent holes on the top of the cartridge to prevent it from drying out on the shelf or during shipping.
After ensuring that the shipping tape has been removed, run the printer's "Head Cleaning" utility to prime the cartridge, then print a test page.
See full detail at- http://guideusermanual.com/product-name-workforce-wf-3640-manual&po=152836&lang=English

Sep 18, 2014 | Epson WorkForce WF-3640 Wireless Color...

1 Answer

How can i calibrate print head of pagewriter trim 1


It would help if you stated the manif. example. Phillips, HP, hewlett Packard. ect.

You should be able to find service information on the bottom of unit.

May 08, 2014 | Office Equipment & Supplies

1 Answer

Why is print quality poor after inserting new ink. Copies are faint and have lines


the cartridge is clogged with ink that has dried and reduced the slit. you need to replace the cartridge with a new one. it happens usually if you recharge the cartridge 3 or 4 times with compatible ink.

May 07, 2014 | Office Equipment & Supplies

1 Answer

How to clean ink absorber for canon mp237


First of all open the ink cartridge of your printer.
When the ink cartridge would move all the way over, then disconnect the power cord of your printer.
Now pull the frame of rubber from the printer and remove ink pads.
To clean ink pads you may place them in a bowl having warm water and start rubbing and squeezing them to clean it from ink.
After removal of ink, keep the pads separate for dry.
When the pads get dry completely, place them back in rubber frame.
Reinstall the rubber frame in your printer.
For deep guide and support refer to-
Canon Pixma Mp237 Manual

Oct 07, 2013 | Canon PIXMA MP230 Multifunction color...

3 Answers

HP Laserjet 3330. Scanner bulb warming up doesn't go away. I have done the "solution 1" as discribte but nothing is happening. It goes like: - i put the power on, hewlett packard is flashing, the...


How does the bulb look? Is it bright or kind of dim. The bulb warming error is designed to halt use of the machine until the scanner bulb reaches the correct output level. As these are basically a flourescent tube, they will dim over time and at a certain point they will not generate enough light to enable proper scanning. If the bulb is dim, it will require replacement.

Mar 14, 2011 | Office Equipment & Supplies

2 Answers

HP printer psc 2210 all in one


Chances are that you didn't lock down the scanner when you moved the unit. You can attempt to open the unit and move the scanner bar manually to reset it. HPs are very difficult beasts when it comes to their power up check out. It must be fully functional...including all cartridges...to work in most cases. Good luck.

Dec 20, 2007 | Office Equipment & Supplies

6 Answers

Printer won't recognize cartridge


I had the same problem. I'm not sure but I think I replaced the cartridges when the printer was on because I turned the printer off and removed one of the cartridges. When I turned the printer back on it recognized that cartridge but not the others. I turned the printer off again, rmoved all cartiridges and put them back in when the printer was still off. When I turned the printer on again I had no problems. So...try turning off the printer, rmove all cartridges, then put them back in and restart printer. Hope this works for you .

Nov 28, 2007 | Epson Stylus 2200 InkJet Photo Printer

Not finding what you are looking for?
HP Deskjet 5940 Photo InkJet Printer Logo

Related Topics:

664 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Vinaya Kumar...
Vinaya Kumar...

Level 3 Expert

1121 Answers

Seeker5211
Seeker5211

Level 3 Expert

1088 Answers

kakima

Level 3 Expert

98694 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...