Question about Washing Machines

1 Answer

Beeping twice but no water showing in drum and will not start new cycle

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

Likely the timer has failed.
unplug for 40 minutes in an attempt to reset the ECU.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Sep 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i do is showing;tech. fault F53 and F63


F53 indicates that it is the issue of speed sensor. You can unplug the washer then plug it back in and set sanitize cycle. As soon as it begins,cancel the cycle. Then try any cycle again and see what happens. These washers have a severely sensitive balance system.If the load is at all off balance,it should at least attempt to get revving up. If it does f53 again, check to make sure it is firmly balanced/leveled onto the floor firmly.Try again and if it fails, please contact the Manufacturer

Jul 22, 2016 | Speed Washing Machines

1 Answer

When i put the wash cycle on it goes and does fill up with water, but then when comes to spin cycle it stops agitating and starts beeping constantly with the light on where the "lid locked" icon is.. When...


Hi Ellie,Just read your posting.Now does your machine drain most of the water from the machine but it does not spin the clothes dry?Is this correct?Also does the mahine only show the lid lock icon when the machine is beeping?Please reply with additional information on the questions and I am sure I can help you.Looking forward to your reply.

Aug 17, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Takes long time to start washing cycle, makes groaning sounds as it gets started, then barely into process it beeps and flashes "f" and "h" alternately.I noticed that when I tried the "rinse/drain" cycle...


F/H" No water detected entering machine or Pressure switch trip not detected.

If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed.
Or
If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash.
Press PAUSE/CANCEL twice to clear the display.
  • If there is no water in the unit:
    1. Make sure that both valves at the water source(s) are turned on all the way.
    2. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves
    3. Check inlet valve operation
  • If there is water in the unit:
    1. Check Drain pump operation
    2. Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch
  • Check there is not a siphon problem
  • Check wire harness connections to:Inlet Valves, Pressure Switch, Drain Pump, Flow Meter, and Central Control Unit (CCU)
  • Check all hoses for possible leaks
  • Check pressure switch operation
  • Check flow meter operation
  • Check CCU operation

Aug 12, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Shows "LE" in display.


Machine has a bad motor or "stator" on this machine. It is a direct drive winding on the back of the machine. Remove the back panel, the one bolt removes the rotor then you will see the stator winding, replace it and your good to go.

May 11, 2008 | Washing Machines

1 Answer

Water drainage problem


I continued to push the set delay and end of cycle buttons, twice. Then I pushed the jeans cycle button and let it run its course. After doing that twice, it drained the drum and I tried to start a new cycle for washing, which worked. Yea!

Mar 29, 2008 | Kenmore Elite 21082

1 Answer

F-H code and beeping noise


error code which is serial communication error with motor contrl.
replaced M.Contl.brd but still have error.

Dec 03, 2007 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...