Question about Dell 3000cn Laser Printer

1 Answer

My printer keeps showing an error "Front Cover open Close it" athough every cover is perfectly closed

Although every cover is perfectly closed it keeps giving the same error message. When I contacted dell they gave me a reply to change the printer rather than spending time and money on it with a dell technician. Is there a way this can be diagnosed.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 59 Answers
Re: My printer keeps showing an error "Front Cover open Close it" athough every cover is perfectly closed - Dell 3000cn...

What's the error say?

Posted on Jun 15, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Error code - 001-302

check if the front cover is closed properly. If this doesn't work try rebooting the printer with the front cover open. Close it when it started up. Clean sensors. All not working. Engineer.

Nov 27, 2013 | Xerox WorkCentre 7328 Colour Multifunction...

1 Answer

EL Error

Don't know your printers model but try this:
  • Open and close your printers front cover make sure its perfectly locked into place.
  • Check on the printers drum unit,and make sure its in good working condition.
Hope it helps.Thanks!

Mar 02, 2012 | Printers & Copiers

1 Answer

Message 'Clean Sensor' has appeared. Followed advise to open Cover D and close it again but to no avail. Has anyone got any other suggestions, please?

Follow the steps below to clear the "Clean Sensor" error message.
  1. Open the front cover of the printer (cover D). c2600_cover_d.jpg
  2. Slowly close the cover again. c2600_close_cover_d.jpg This action will move the lever shown below and clean the sensor.
  3. Open and close the cover several times. Once the front cover is left closed the printer will start to calibrate.
Once complete, the error should no longer appear and the printer should resume normal operation.

Note: If the error message is still apparent after following the steps above, contact Epson for further advice.

Nov 16, 2010 | Epson AcuLaser C2600N Printer

2 Answers

Getting "inner cover is open" message

The inner cover is a flap on the inside in front of the carriage when it is at rest when the cover us open. You had to flip the inner cover down to access the ink cartridges.
Open the cover. The inner cover is in the center and need to be flipped up.
Good luck.

Dec 04, 2009 | Canon Pixma MP500 All-In-One InkJet...

1 Answer

Error light keeps on flashing blue light at the

These are your possibilities based on your error.

Front cover is open
Close the front cover of the printer.
Fuser cover is open
Close the fuser cover located behind the back cover of the printer.
Paper jam
Clear the paper jam. See Paper jams and how to clear them on page 85. If the printer
does not start printing, press the Go button.
Memory full
The printer memory is full and the printer cannot print full pages of a document. See
Solving print problems on page 97.
Print overrun
A print overrun occurred and the printer cannot print full pages of a document. See
Solving print problems on page 97.

Jun 14, 2009 | Brother HL-2170W Laser Printer

3 Answers

Replaced Drum still says "Replace Drum Soon". How do I reset on a Brother 7420?

Reinstall the new drum unit, keeping the front cover open. Press OPTIONS. Press 1 when the display shows REPLACE DRUM? 1.YES 2.NO ACCEPTED. Close the front cover.

May 28, 2009 | Brother MFC 7420 All-In-One Laser Printer

1 Answer

Showing drum error and replace toner low message all the time

Open the cartridge cover
push "option"
and push "00"
wait until the word "accept" then close the cover,
after that should be working perfectly.

May 21, 2009 | Brother MFC 7420 All-In-One Laser Printer

2 Answers

My mp600 keeps saying close inner cover-which is closed

I had the same issue, turning off didn't solve it.
There's a plastic flap the width of the print tray just inside that I flipped up and it solved this problem. It is directly in front of the ink tanks. I'm assuming we flipped it down and forgot about it. It seems it needs to stay up, although you wouldn't notice it when it flips down when you close the top, as it closes just fine with it down. It's easy to overlook. This took me a few hours to realize.

The top of the flap has a half circle cut out of it in the middle.

Dec 18, 2008 | Canon PIXMA MP600 all-In-One InkJet...

3 Answers

Cd tray error Canon Pixma MP810

Sorry a little late only just read your problem.
The location is not the bottom tray feeder but the disk tray. In settings change your media type to "Printable Disk" the paper scource should automatically change to "Disk Tray" and hopefully every thing will work OK.

May 19, 2008 | Canon PIXMA MP810 All-In-One InkJet...

3 Answers

Printer cover open error message

I had that problem too.

Unplug the printer.
Hold the printer cover open while you plug in the printer.
Then wait for the printer to power on while still holding the cover open.
Then close the cover.
The buttons should work and th error message should be gone.

It worked for me.

Nov 01, 2007 | Lexmark X2250 All-In-One InkJet Printer

Not finding what you are looking for?
Dell 3000cn Laser Printer Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dell Printers & Copiers Experts

Prashant  Sharma
Prashant Sharma

Level 3 Expert

1127 Answers

Rick Johnson
Rick Johnson

Level 2 Expert

84 Answers


Level 1 Expert

3 Answers

Are you a Dell Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides