Question about Dell PowerEdge 1600SC Server

1 Answer

Hard disc Problem for server (powerEdge 1600SC)

There is long beep continuosly once you on the mashine,there fore kindly, we look forward for your assistance.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Dell Master
  • 829 Answers

Hi , I suppose its a issue with the RAM , Kindly check re-inserting the RAM on the server and try booting the system

Posted on Jan 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi. I Inherited a DELL Poweredge 1600SC server. When I switch it on, it powers up but the screen remains blank [black without any beeps]?? I remove all the memory and switched it back on again = NO beeps....


I guess you can't go into start button. /anyway how did you know if computing is powered? On your keyboard top line keys have screen control keys for brightness etc.eg f4. try.

Aug 01, 2013 | Dell PowerEdge 1600SC Server

1 Answer

A power outage cause dell server 1600sc to shut down & no display on the monitor


Hello here is the homepage.

http://www.dell.com/support/drivers/us/en/ussoho1/Product/poweredge-1600sc

There should at least be a message on the monitor indicating there is no signal coming to the monitor. The first thought that comes to mind if all is connected would be that the power supply has failed.
And maybe the graphic card.

Call also the DELL support in your country they will be glad to help
and they probably know the fault.

Contact Us 1-877-671-3355

Good luck

Nov 16, 2012 | Dell PowerEdge 1600SC Server

1 Answer

I am getting a loud beeping sound from the back of my Dell Poweredge 1600SC Server this morning. It seems to be operating fine, and there are no warnings on the computer. It IS very dusty inside, though....


Hello,

The sound may be an indicator alert. overheating, unlocked latch, etc. If the system is running ok and no noticable problems with your software, check your BIOS setting for log information related to alerts. If you find nothing of significate problems, you can disable alerts in the BIOS.

Hope this helps. Good Luck

C2Solutions

Jan 18, 2011 | Dell PowerEdge 1600SC Server

1 Answer

When powering up a Poweredge 1600sc i get 6 error beeps,the order is 1-3-2


Hi,
It states 1-3-2 = No memory installed
Remove and reset the memory modules (see "Memory Modules"). If the problem persists, replace the system board (see "System Board"). Good Luck

Jan 29, 2010 | Dell PowerEdge 1600SC Server

1 Answer

PowerEdge 1600SC long beep and hang


check the Cmos battery. or levae pluged in over night and then check setup setting you battery went dead

Oct 12, 2009 | Dell PowerEdge 1600SC Server

1 Answer

Our 1600sc dell server is beeping continuosly.


Check the PowerEdge Raid Controller for parity problems. Sounds like the status on the physical volumes participating in a RAID array has been degraded.

Loud beeping from a drive is usually an indication that an invalid drive array member has resulted in a degraded logical volume.

If you were counting correctly, you had at least three drives - most likely participating in a RAID-5 setup. The array might have been rebuilt with one bad drive. But it sounds like you've got two corrupt physical volumes in the array. And that's not good.

Hope you've got a backup!

Jan 19, 2009 | Dell PowerEdge 1600SC Server

3 Answers

Dell PowerEdge 1600SC Server occasionally beeps when running


Check out this site:

http://bioscentral.com/postcodes/dellbios.htm

Write down the exact number of beeps and how long they last to find what the error means. The are call BIOS post codes and they resemble Morse Code. (ie. one long, 3 short, 2 long = RAM issue) Good luck!!

Sep 26, 2008 | Dell PowerEdge 1600SC Server

6 Answers

No Video Signal on 1600sc


Disconnect from the network and all other accessories, and power up the system, this might be due to a faulty device attached to the system, eg: when you connect a usb faulty device the boot takes very long time, sometime it does not boot up.

Dec 30, 2007 | Dell PowerEdge 1600SC Server

Not finding what you are looking for?
Dell PowerEdge 1600SC Server Logo

Related Topics:

264 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dell Computer Servers Experts

Jax Planet
Jax Planet

Level 2 Expert

921 Answers

Shawn DuRee

Level 3 Expert

353 Answers

Edd nugent

Level 1 Expert

37 Answers

Are you a Dell Computer Server Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...