Question about E-Machines EMA IMPERIAL GV (845GV) TG3 eMachines (145119) Motherboard

3 Answers

Replaced hdd on emachine w3615,light on mobo but it wont come on.

Replaced hdd on e machine w3615,green led on motherboard is on but the computer wont come on.

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

You can enter safe mode (F8 when booting up) to retrieve windows password while you forgot user account password, but when you forgot admin passwords, there's no way to change it, you need to use tool to recover admin password. Last week, I forgot my Windows admin password. In the end, I successfully retrieve my Windows password with Windows Password Seeker in http://www.passwordseeker.com. It's worth an attempt.

Posted on Mar 16, 2012

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

For removing Windows login Passwords safely, I strongly recommend windows password program. Few days ago, I downloaded one at http://www.reset-windows-password.com I burned it to a Usb memory card. Booting up and clearing my password within just 5 minutes

Posted on Mar 15, 2012

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,351 Answers

Hi ipackrat21, that little green led you see is telling you the motherboard has standby power. (Its supposed to be green & on).
Make sure the hdd jumper is set to, master without a slave). In a one hdd system.
When you replaced the hdd you also need to enter the bios menu.
In the bios you'll need to make some changes. First you should see the new hdd listed in the bios. (Normally it list the hdd by model). If your hdd is shown than go to the title "BOOT". You need to set the boot order. A normal boot order would list like so;
First boot device, Floppy disk drive".
Second boot device, "CR-ROM" drive.
Third boot device, "Your new hdd".
If your bios does not see your hdd you'll need to re-check the data cable from the board to the drive. (Make sure it is fully connected).
If the drive is an IDE/PATA make sure it has power. A 4-pin molex.

replaced hdd on emachine w3615,light on mobo but i - 010e000.jpg Good luck ipackrat21!
Still have trouble, post it here.
Mike

Posted on Jan 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fans work green light shows on motherboard but cpu wont power up


Any HDD light on / if not could be failed HDD OR faulty IDE / Sata cable.

Did you get posting beep if not remove / replace ram / reboot.

If you did then either mobo / CPU may be faulty.

May 10, 2010 | Intel D845GVSR Motherboard

1 Answer

Need to re-attach power button cable, hard drive


The manual for your computer is available from emachines, p.168 shows the info you need (replacing the front I/O panel)
http://downloads.emachines.com/userguides/8511279_eM_NG3_chassis_HW_ref_en.pdf

The good news is that you can't harm the computer by connecting the wires wrong and the bad news is they just won't work the way they are supposed too if not connected properly. The LED's must have the correct polarity to work.
In general, if you look real close (as in magnifying glass and flash light) you will see the ID for each set of pins is printed on the motherboard (pwr,rst,HDD,pwr sw,speaker) Just match what it says on the motherboard to what it says on the wires. Don't worry if you get the polarity wrong. If a light doesn't work just swap the two wires. The colored wires should be positve (+), though. The reset (rst) and power switch (pwr sw) wires don't require polarity.
These instructions are for most computers in general, YMMV.

Nov 30, 2009 | E-Machines eMachines Desktop PC

1 Answer

On the emachine w3615, there is a red/white & a green/white wire that says ''LED'' - next to it is a black/white wire that says ''power sw''. my question: where does this black/white wire go? i was...


you have no power on your pc what so ever? those wires are strictly for LED function. if you have no power at all then there's another problem possibly a power supply or a disconnected wire on the mobo

Oct 02, 2009 | Gateway Computers & Internet

1 Answer

Emachine....uhh...wont turn on.. green light on motherboard. help


well this would be more simple for me since i have more than one pc so first thing i would do is try another power supply if that wont turn it on then i would say mobo, the PSU's of the emachines are **** and dont last too long...
well i would try the PSU first since its cheaper.
good luck

Aug 24, 2009 | Microsoft Windows XP Professional SP2 Full...

2 Answers

NEED POWER SWITCH WIRING FOR A EMACHINE T-3095


check on the motherboard there should be a small prints on it near control panel.

Mar 05, 2009 | E-Machines eMachines T3830 PC Desktop

1 Answer

Motherboard wiring


Green/wht normally = Reset or Power LED
Red/wht normally = HDD LED
And is the third red/BLACK?
There should be a label on the black pin jumper at the end of each wire.
Does it say anything?

Jan 16, 2009 | E-Machines eMachines Desktop PC

1 Answer

Emachine T2862


It sounds like the motherboard is toast

Didn't find anything on EBay for a motheboard

You can get a replacement Dell wo/monitor for $299 +Tax/shipping

http://www.dell.com/content/products/category.aspx/desktops?c=us&cs=19&l=en&s=dhs

Jul 10, 2008 | E-Machines eMachines Refurbished EMA...

1 Answer

Emachine desktop w3615


  1. START UR COMPUTER
  2. ENTER YOUR MOTHERBOARD SETUP
  3. SETS ALL VALUE TO DEFAULT
  4. SAVE IT
  5. THEN RESTART UR CPU

Jun 28, 2008 | E-Machines eMachines Desktop PC

2 Answers

Wiring info


Most Mobo's have printing next to the places that are jumpered or pluged into. The ones you need sould be close to the edge of the mobo, that is close to the front {power button} side.

May 30, 2008 | E-Machines (308714) Motherboard

Not finding what you are looking for?
Computers & Internet Logo

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top E-Machines Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18381 Answers

Are you an E-Machines Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...