Question about Porter Cable-Cable 30mm Template Guide for 43936 Bit - 42050

1 Answer

Missing set of instructions for the porter cable template guide

I need to get the set of instructions for the porter cable template guide kit model 42000

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,176 Answers

Not having any luck with manual. All they say is you have to contact the service center for that. If you cant find anything let me know, I am in contact with a center at least once a week.

Posted on Jan 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Are the 7 degree dovetail bits, that come with the jig, the only size that can be used or can a 9 degree bit be used?


Hi, W/D at your service.
Apparently, there are several types of bits compatible with your model.
Here's a link that gives you a better idea:
http://www.toolup.com/porter-cable_4216_12-deluxe-dovetail-jig-combination-kit.aspx
Best regards, --W/D--

Feb 23, 2011 | Porter Cable Porter-Cable 4216 12" Deluxe...

1 Answer

Need copy of owners manual.


http://www.dewaltservicenet.com/documents/English/Instruction%20Manual/Porter-Cable/891038.pdf this is for type 1,,,if you need a different type then go to http://www.dewaltservicenet.com/ in the middle is a section titled "need a manual?" just enter in your model number and it should pull it up or if you don't know off hand then enter 557 and it will bring them all up for type 1 through 4

Jun 13, 2010 | Porter Cable - Cable 557 Factory -...

2 Answers

Need an instruction manual for a Model 557 Porter Cable Plate Joiner


Owners manual is here. Exploded diagram is here.

I would like to note the manufacturers site lists 557 Types 1-4. Not sure what the difference between them is, but if you need the link, it's here on page 4 of 5.

If this answer helped, please vote. Thanks!

Apr 10, 2010 | Porter Cable - Cable 557 Factory -...

1 Answer

Blade change problem for Porter Cable 557 plate joiner


Putting it in the freezer for a couple of hours may loosen the screw by contraction and or you will have to use an impact wrench unless it is completely stripped , then you will have to drill it out.

Apr 08, 2009 | Porter Cable - Cable 557 Factory -...

1 Answer

I need operating instructions


Here is a direct link to your owners manual. You can print it if you want a hard copy or you can order one from porter cable.

http://www.dewaltservicenet.com/Products/DocumentView.aspx?productid=65507&typeId=14816&documentId=30657

Hope this helps.
Richard

Mar 09, 2009 | Porter Cable Porter-Cable 4216 12" Deluxe...

1 Answer

Dovetail leave a 'light gap'


This may not be related to your jig. It may be movement in the vertical axis resulting from:

  1. The router bearings being worn allowing the bit to move up and down.
  2. The router bearings worn allowing the spindle to deflect side to side which changes the bit height slightly (cuts on the edges, making the cut a hair deeper).
  3. The router collet or router spindle worn, allowing the bit to move during cuts.
  4. The jig guide plate deflecting or no longer flat.
  5. Excess vibration in the router causing the wood to move in the jig.

To check the bearings; try routing the cut with a straight bit first to clear the wood for the dovetail bit. Then cut with the dovetail bit (a new one preferably) using very light feed pressure. Is the joint tighter? If so then the bearings are worn. Have the router serviced or replace it.

Check the end-play by pulling on the router shaft, does it wiggle slightly in and out? If so this is your problem. Have the router serviced or replace it.

Be sure the wood is flat and the faces planed parallel, if they aren't the dovetail line will be straight but when you assemble there will be slight end gaps in sections of the dovetail.

Feb 23, 2009 | Porter Cable Porter-Cable 4216 12" Deluxe...

Not finding what you are looking for?
Porter Cable-Cable 30mm Template Guide for 43936 Bit - 42050 Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porter Measuring Tools Experts

Hasan Khan Amran
Hasan Khan Amran

Level 2 Expert

180 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Joseph Mueller
Joseph Mueller

Level 2 Expert

335 Answers

Are you a Porter Measuring Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...