Question about Ultrex 834-334 Die Cast Work Top Blender

2 Answers

Blender problem Blender work for a while and then the completely stopped. Is there a fuse on this blender?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers
Re: blender problem

Yes there is, however unless you are very mechinal incline I won't suggest that you try to replace the defective terminal fuse. This is cause by running your blender continuous. Let me know if you are welling to do the repairs yourself, so that I can give you the directions. Sign, Spurs21

Posted on Jun 12, 2007

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: blender problem - Ultrex 834-334 Die Cast Work Top Blender Blenders

My husband is good at this so let me know

Posted on Dec 26, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

My kenmore blender stopped blending!!!

There is a gear underneath the blender blade. This connects the blade to the motor found on the base of the blender. This gear usually get worn out specially if the load that we are giving to the blender is beyond its limit. I hope you could by a spare on one of the electric shop near or might as well consider buying a new set.

Oct 06, 2009 | Kenmore Blender Single-Speed Blender

2 Answers

Blender died ...... motor won't turn on

Have you tried the fuse first....

If it is the motor (quite rare), these people may be able to order you one:

Aug 10, 2009 | KitchenAid KSB3 Classic Work Top Blender

1 Answer

Kitchenaid Blender Classic

Same thing happened to me. Opened it up and along the red wire to the motor is a bass fuse. Went to the hardware store and then I replaced it. Works fine.

Apr 12, 2009 | KitchenAid Kitchen Aid Kitchenaid 5-speed...

2 Answers

Lost blender fuse

There are no service manuals available for this model. If you can figure out what fuse it takes, Radio Shack most likely has them. What are the specifics?
It can be figure with the electrical information. You will still have to get the right physical size though.

Feb 12, 2009 | Oster 6854 14 Speed Blender

1 Answer

My nblender just stop working, power in was good, no reaction.

Switch must be bad, remove the four screws on the bottom they are under the feet, then check switches, and replace broken one.

Nov 19, 2008 | Vitamix 5000 Work Top Blender

2 Answers

Received the Breville Ikon 600 blender as a Christmas present in 2006 and have used it 3 times, with the third time being this past weekend. The product is now out of warranty and low and behold, it...

My IKON 600 Blender fuse had blown. It was located on the circuit board and can be found by removing the bottom of the blender. Fuse is Fast Blow 10A, metric 5mmx20mm. The fuse blew because the bearing in the bse of the jar froze. Bearing # 608-RS. The beraring froze because the seal in the base of the jar was leaking. Solution: Clean seak surfaces, replace bearing and fuse. Total cost of $6 with my labor.

Apr 16, 2008 | Breville CBL10 BlendMaster Classic Work...

1 Answer

Cusinert blender

you most likely have blown the thermal fuse. I just fixed my blender which had the same problem but only after I bought a another base:< If you are a handy person, it is a very simple fix. buy a 10 amp thermal fuse from "RadioShack" for $1.69. Sadly, it is cheaper to buy a new blender than have it fixed at a repair shop.

Mar 19, 2008 | Cuisinart SPB-7 SmartPower Work Top...

1 Answer

Blender stops working

I also have the same is brand new...worked 3-4 times and stopped. Spent $65 for a nice blender. I will also NEVER buy black and decker again.
Dallas, TX

Oct 12, 2007 | Black & Decker BL1900R Blender

1 Answer

Stopped working

i had the same problem after only one month, took in back to walmart and they would do nothing. i love the big heavy glass jar on this model so i baught another on thinking i broke it some how and guess what, the second one stopped after one and a half months. called around and no one would do anything for me, company sucks, i took the bottom cover off the blender to expose the problem and there is a problem with the curcuit board and built in breaker. i ripped out all the speed buttons and curcuit board and just wired in a on/off switch to the motor. works great again. i still had a extra broken blender so i took a old chain saw i had and turned that one into a gas powered blender. problem solved, any questions please feel free to ask.

Sep 01, 2007 | Black & Decker BL5000 ProBlend Work Top...

1 Answer

Thermal cut off fuse replacement

I worked for sunbeam and they were 10amps there. dont go to high because u start a fire ..also while you replace it look for darker or blacking field wires..all wires should look good. but hard to start a fire when u got your finger close to off the button at most it will do is slow down and stop ...smoke...time for new blender then. CrazyLarry

Jun 03, 2007 | Cuisinart CBT-500 SmartPower Premier Work...

Not finding what you are looking for?
Ultrex 834-334 Die Cast Work Top Blender Logo

Related Topics:

419 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ultrex Blenders Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers


Level 2 Expert

86 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you an Ultrex Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides