Question about Homelite Consumer Products 9.0 Amp, 14 In. Chainsaw

1 Answer

Loss spark My Homelite UT10946D will start & run fine until it warms up then it will stop running. I can not get it started until it cools down (hours later) I checked my spark and I have none. After it cools, I will have spark again and it will start. Than the same cycle all over again, warms up then stops. What is the cause and what part do I need to replace.

Posted by on

  • Anonymous Mar 24, 2009

    same thing for me on a 14" McCulloch

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 211 Answers

Hi

You need to replace the coil but first try to change the sparkplug and see what is happening.

best regards savumihai71

Posted on Jan 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My homelitechainsaw HCS 3335 runsfine for about 5 minutes then just cuts out and i cannot start it until it has cooled down what is the problem


hello,After it stalls take the fuel cap off and put it back on and see if it starts,maybe the cap is bad or clogged and not letting air in to equalize the pressure of the fuel being used in other wards a clogged vent, this is a small thing but a big problem,,hope this helps, 11

Feb 20, 2012 | Homelite Garden

1 Answer

I have a Homelite Chainsaw 45cc Power Stroke. Model No. UT10946D. The chain brake is always applied. Brake lever will not latch in the released position. I've disassembled it and do not see anything...


I have the same model (ut10946d) and used it for less than 2 tanks of gas when the chain froze. I noticed it was slowing down and it seemed like the chain brake was not disengaging and staying in the "unlocked" position.
I took the tool apart today and found that the band that rubs on the clutch to stop the chain was dragging on the clutch because it doesn't disengage all the way. The heat from the friction melted the plastic parts around the clutch housing and crankshaft. So now I have a chainsaw that I bought new, used for less than an hour, and is now junk due to poor design and/or product control.

I WILL NEVER BUY ANOTHER HOMELITE GAS POWERED TOOL AS LONG AS I LIVE. THEY ARE PURE JUNK!

My solution, call homelite and complain about it, maybe they'll stand behind their design flaws - but I doubt it.

Jun 18, 2010 | Garden

1 Answer

Will not start


That seems to imply that the check valves in the primer pump and in the fuel pump section of the carburetor are bad or the air pressure just forced by the valves. The line without the filter is the tank return line from the primer pump. The primer pump is supposed to pull fuel from the fuel filter into the carburetor flooding all spaces within it it, then passing out to the primer pump and from there, back into the tank. Does the primer bulb fill with fuel after several pumps? The first try may take longer because you forced all of the fuel out of the carburetor with the air pressure. Make sure all of the carburetor fasteners are tight. It's possible that you have injured the diaphragm in the carburetor lower chamber when you blew air into the line. Go to: www.drystacked.com for a 12 page article on Walbro carburetor theory and troubleshooting. Make sure the spark plug gap is set at 0.020". Hope some of this helps!

Jun 22, 2010 | Homelite Consumer Products 9.0 Amp, 14 In....

1 Answer

Chainsaw won't start when warmed up


Coil is possible, change the plug (cheap insurance) and try it. If problem persists try this shortly after it quits.
Ignition Coil Test by SmallEng.com
http://www.youtube.com/watch?v=L7WNBDRG4C4
You may need to use a jumper wire between the threaded part of the plug and the cooling fins. You do not have to bend up the electrode.

An index or business card is good for gap tool. Remove the plug, rotate until magnetic attraction pulls coil and card tight to flywheel, then tighten coil screws. Rotate flywheel until magnetic attraction eases, remove card, rotate a couple of revolutions and ensure nothing drags or contacts flywheel.

Homies are bad for clogged fuel vents too. When it begins to sputter roll it onto side and loosen fuel cap. If ti smooths out and runs properly it has a clogged vent. HTH
Lou

Dec 22, 2009 | Homelite Garden

3 Answers

Homelite chain saw quits in 15 minutes


Why are you not standing on the help desk where you purchased this? If it starts to sputter then dies It is probably a plugged fuel tank vent. When it begins to act up roll the saw so the fuel cap is up right and loosen it a little. If it smooths out and runs correctly you just vented the tank and that is where the problem lies. If it suddenly stops running with no warning it is most likely an electrical problem. If you repair either of these problems it may void your warranty. Why not make Homelite repair or replace it? If offered a refund I would not purchase any product by the same manufacturer. At best their quality control is lacking. HTH
Lou

Nov 23, 2009 | Homelite Garden

2 Answers

My 18in homelite saw starts ok, cuts fine but, when you shut bdown to refuel or take a short break, (over 5 min) it will not restart till it cools down or about a half hour. Thanks


Loosen the fuel cap when you shut it down tighten it before you restart. If this fixes it you have a plugged fuel vent. HTH
Lou

Oct 06, 2009 | Homelite Garden

1 Answer

Runs well untill it gets hot. then cuts out


If it's the little xl model, it's probably the ignition coil breaking down when it gets hot and therefore it can't and won't be able to handle a load. Also, scarred pistons skirt or rings could also be some of the problem here. Make sure your mix for a Homelite saw is 40:1 not 50:1 like most saws are. Homelite seems to run better with a heavier oil mixture. Good luck.

Aug 02, 2009 | Garden

Not finding what you are looking for?
Homelite Consumer Products 9.0 Amp, 14 In. Chainsaw Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Homelite Garden Experts

Jim Parker
Jim Parker

Level 3 Expert

1040 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

375 Answers

Jay Finke
Jay Finke

Level 3 Expert

1224 Answers

Are you a Homelite Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...