Question about Indesit W 123 Front Load Washer

Open Question

Indesit wg 1233 t won't wash or spin

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
barkencoa
  • 3463 Answers

SOURCE: indesit washer model number wg 1432 wont spin

Make sure the washer has fully drained, if it has filter, remove and clean, check your user instructions if you are not sure.
If you stillcan't get it to spin after these checks, come back to me.
PLz rate this solyution.
Thanks.

Posted on Jan 03, 2009

Ad
  • 784 Answers

SOURCE: My Indesit washing maching WG

Usually, when water fills up to a desired level, for example: choosing a small, medium, or large load. The floating switch will trigger a signal to turn on the motor to turn to start the agitation. In this case, the floating switch is bad or the floating mechanism is not working. Therefore the machine didn't do anything. It needs to access to inside the back panel to check it out. Cheers.

Posted on Aug 13, 2010

  • 330 Answers

SOURCE: I have a Indesit WG

there are only two parts in the machine with enough power to take out the safety switch the motor & the control board you have to disconnect the motor plug from the motor then switch the machine on if it trips the switch its the control board if it doesnt trip the switch its the motor.

Posted on Jan 10, 2011

imufo2
  • 3773 Answers

SOURCE: I have an indesit wia 101 front loader washing

HI,
Check back of washe with a flashlight for a bent or clogged drain hose. Do not move washer to check it. When you move it , it will straighten out and you will never know if it was bent
Also while it is pumping , pick up end of drain hose at drain and observe the volume of water being pumped.
If no water then the Pump may need replaced
Thank you for using fixya
Leo Ponder
Please rate me if this helped

Posted on Aug 12, 2011

  • 6277 Answers

SOURCE: I have a indesit wm12x

Hi from retired Englishman in SW France,
It's doing that because it is unable to drain all of the water out of your washer I suspect ;-0)

I would gently suggest as a first step that you clean the drain motor/pump lint tray/filter. So many 'faults' are caused by blocked filters and many machines will not even go to rinse or spin or release the door lock if there is any water still left inside.
Following are my complete and hopefully 'coverall' pre-typed guidance notes for checking both the drain motor filter and the drain motor ;-0)
REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT (alternatively use a wet vac as sensibly suggested by VinnyB1234!)
If you are unsure where the filter is, it is often behind the front lower (kick) panel (or in some machines at the rear in an awkward position!). These panels are either held on by (plasic) screws or will just pull off. Most filters are held in by a round cover/knob. Sometimes the filter will not come out with the cover and you will have to persuade it to come out to play.
It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. Using something suitable like a glove see if it is easy to briefly slow the motor down. If it is easy then the motor is malfunctioning.

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

Posted on Sep 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does this mean? My machine is very new & won't drain it won't go through a full cycle & won't spin properly now it's bleeping with this flashing up on it!


Turn off machine and check water waste filter to see if blocked should be at front at bottom of machine or at back,not sure this is the cure but hope it helps

Apr 06, 2013 | Washing Machines

1 Answer

Indesit model widl106 won't spin after the first wash. Lights flash.


If the water flows though the inlet then the flow pressure should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.
Test a pressure switch: Click on : http://www.youtube.com/watch?v=HZZ2bDMspj8

Jan 23, 2013 | Washing Machines

1 Answer

Flashing lights


There is a Light Flashing on my Indesit Washing Machine


Many of our newer Indesit Washing Machines have a series of indicator lights, which flash to indicate a possible fault on your installation or simply to let you know a problem occurred whilst you were away from your Indesit Washing Machine.


Pre wash light flashing
Indicates a failure of your Indesit Washing Machine to fill correctly. Check your fill hoses for a blockage, a leak, a kink or to make sure that they are turned on.

Wash light flashing
Indicates that your programme dial has been moved from its original position. Simply returning the wash dial to its original position will restore the light to its original status.

Spin light flashing
Indicates that the Indesit Washing Machine has considered the wash load to be excessively un-balanced. Open up the door of the Indesit Washing Machine, re-distribute the garments and retry the spin to resolve this.

End light flashing
Indicates that the Indesit Washing Machine has reached the end of a wash programme.

Wash, rinse and spin lights all lit at the same time would indicate a possible blockage in your under sink wastes system. Check out the additional informationin our 'My Indesit Washing Machine Will Not Empty'

Aug 22, 2012 | Indesit Washing Machines

1 Answer

Can I ask for a washing machine manual Indesit WG 833 in Polish best if you can not board it in English.


Hi from retired Englishman in SW France,

I'm so sorry but this forum does not, nor is in a position to, supply any type of manual (service or otherwise), parts list, installation instructions, electrical or schematic diagrams direct; it's just made up of ordinary guys and gals, probably at home and from all over the world, with experience of addressing problems and giving guidance for free on the web ;-0)
Also members on Fixya are not 'affiliated' to, or representative of, any manufacturer at all, just using their experience gained probably over many years.

Manual
You will need to type into your search engine/web browser '(make model number) washer manual' and you should be presented with a number of sources from which you can either download for free or have to pay a nominal amount.
You could also try the manufacturer's web site direct ;-0)

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C.

Sep 19, 2011 | Indesit W 123 Front Load Washer

1 Answer

I have a Indesit WG 1030 washing machine which when I switch it on takes out all the electricity in the house. Do you know why this is so. It is not the plug.


there are only two parts in the machine with enough power to take out the safety switch the motor & the control board you have to disconnect the motor plug from the motor then switch the machine on if it trips the switch its the control board if it doesnt trip the switch its the motor.

Jan 10, 2011 | Indesit Washing Machines

1 Answer

My Indesit washing maching WG 1234 T, just keeps filling up and will not start its wash cycle.


Usually, when water fills up to a desired level, for example: choosing a small, medium, or large load. The floating switch will trigger a signal to turn on the motor to turn to start the agitation. In this case, the floating switch is bad or the floating mechanism is not working. Therefore the machine didn't do anything. It needs to access to inside the back panel to check it out. Cheers.

Aug 13, 2010 | Indesit Washing Machines

1 Answer

Indesit washer model number wg 1432 wont spin


Make sure the washer has fully drained, if it has filter, remove and clean, check your user instructions if you are not sure.
If you stillcan't get it to spin after these checks, come back to me.
PLz rate this solyution.
Thanks.

Jan 02, 2009 | Indesit W 123 Front Load Washer

1 Answer

Indesit WG 635 P


model no req and product no.

Oct 05, 2008 | Indesit W 123 Front Load Washer

Not finding what you are looking for?
Indesit W 123 Front Load Washer Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Indesit Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Darren Moxam
Darren Moxam

Level 2 Expert

67 Answers

Are you an Indesit Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...