Question about Mitsubishi WS-55511 55" Rear Projection Television

1 Answer

Mitsubishi ws 55511 replace convergance ci and now set wont power up doesnt stay on long enough to get trouble codes

Tested continuity on all the solder points and all wiring back-in place only powers up for 3 sec. then off

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mitsubishi Master
  • 14,553 Answers

How did you get at the part/s? remove chassis or just the center board? I suspect something happened when you repaired the set.

Does the self check which even if set does not come on, power light comes on for a few seconds and goes off, do the self check (let me know if you need to know how) and see what blink code the power light gives.

Posted on Dec 13, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 126 Answers

SOURCE: powers on for three seconds then goes off

The first thing to do is to try to determine why the set is not turning on. It is equipped with a self diagnostic feature. On the front of the set push the MENU and DEVICE button at the same time and hold until the LED starts flashing a two sequence code. That will narrow things down for us.

Posted on May 05, 2009

fillmore85
  • 62 Answers

SOURCE: how to reset convergence? on mitsubishi ws 55511,

There is an option in the user menu on the tv. Using either the remote or control panel on the front of the tv, press MENU then select SETUP. After you choose SETUP go to the 3rd column with the 3 icons. Here you can adjust the red or blue color or reset the convergence back to factory default.

After a few years the set will begin to show increasing problems with the convergence settings. When you can no longer adjust either red or blue horizontally or vertically an IC replacement will be needed. Your set uses (1) SANYO stk393-110 and you want to make sure it's SANYO and not a knock off brand as those usually fail prematurely.

Posted on Jan 25, 2010

  • 8457 Answers

SOURCE: Mitsubishi WS-55511 convergence problem?

No,need to diagnose.It a 100% convergence problems.Convergence problems very easy diagnose.The picture look like 3D,colors lines don't lines up.Fuzzy,out of focus.Convergence controls don't work to lines up any colors cross.The tech is cheating u if he said cost $125 to diagnose.If u know how to solders u could fix this convergence problems about $100.U can buy a convergence kit at Websites Tv repair World.com,Tvrepairkits.com.The shop everythings fix parts and labors only $300.

Posted on Mar 16, 2010

yarmas225
  • 1 Answer

SOURCE: My Mitsubishi hdtv 1080 Integrated model

Easy fix, pull the DM board ( box with the digital audio orange plug to the left of the patch bay)
this box has several multi cable plugs , but all are labeled with a two letter system and so is the board where they go this makes it easy to put back together
Pull out and open the box ( about 12 screws and then pull the cover off) you will see a small board with 3 cables attached, pull this board by removing the 4 screws and then replace the 7 capasitors with a 25v 1000mf or 35v 1000mf either will work, the 25 volt fit a bit easier. make sure to put the longer leg in the + position on the board! ~ now replace everything and enjoy your set!

Posted on Jul 24, 2010

  • 3 Answers

SOURCE: I have a mitsubishi ws

Age of unit: About 7 years.
Rear Projection HD set, Mitsubishi WS-55511
Nature of problem: Blinking green light of death. Upon plugging the set back in after vacation, the green LED on the front of the set would blink continuously and the set would not turn on. I ordered the blinking green light kit from tvrepairkits.com after seeing this link on a tech forum, suggesting the capacitors were bad on the DM board inside the DM module. The kit arrived within days of ordering. The online instuctions were very detailed and could be followed even by a layman such as myself. Very detailed with lots of photos. My DM module was simpler to remove than the instructions indicated. It simply slid out after about five cables were disconnected from other boards. The module itself is the silver box all the way to the left when looking into the rear of the TV (from the rear of course). There is a plastic guard that surround all the input connections (coaxial connections, home theater control inputs, etc). This is removed with 3 screws. After all the cables to this module are unplugged from other circuit boards, the module will slide out towards you. Then you take the cover off (including the clamp where all the cables are routed into the module) and you can see the DM board (it is labled as such and has 7 capacitors. None of the capacitors were bulged or otherwise defective looking as other posters have reported. Changed them all anyway. Buckled everything up and plugged the set back in. The blinking light started as it always had. It should normally go out in about a minute after plugging in to wall. I really didn't hold out a lot of hope that it would go out....and then....it went out! I pushed the power button and she fired right up! What a thrill! Including shipping, it cost me $45.90 to fix a set I paid about 3000 bucks for 7 years ago and was loathe to just throw away. I certainly wasn't going to pay nearly a thousand bucks to fix this set. It may be a little bulky, but the picture is beautiful as well as the sound system. You guys are great. A very reasonably priced gamble that worked. Watching a movie in HD while I type this, good to have my TV back after almost two weeks without it. I actually can't believe I did it!

Posted on Oct 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i reset my mitsubishi television model#ws-55511


First a reset may not help unless I know what your problem is.

If model listed (WS-55511) IS CORRECT: set has 3 hidden menus:

Option Menu (hard reset of all settings to factory)
Technical Menu (Adjustments for various things)
Convergence Menu for adjusting convergence.

THESE ARE NOT ACCESSED FROM CUSTOMER MENU. Each requires Mitsubishi remote and a 4 digit code .......

So, What is your issue with the set?


I have the codes but it depends on model number and what problem with set is, reset is in Option menu but will not cure all problems.


SD TECH

Nov 10, 2011 | Mitsubishi WS-55511 55" Rear Projection...

1 Answer

MY MITSUBISHU WS 55511 WHEN POWER TURNED ON WILL


I have the same set doing the same thing. I will replace IC and fuses to see if that will fix it.

Jan 05, 2010 | Mitsubishi WS-55511 55" Rear Projection...

1 Answer

Ws-55511 replaced all 7 caps in the dm, still wont power on


I have seen this only 2 times----you may be able to unsolder and remove the reset micro switch---you have to remove the whole screen to get at it---the micro switch board may not be available---the switches can be tested with a ohmmeter set to high end and of course should not have a reading across them--I bet the reset switch is bad--you can remove it and put the keyboard back---most of the Mitsubishi sets use the same type of switches--Only other thing is leave the keyboard disconnected and just use the remote.

Glad you found the problem.

Regards, SD TECH

Sep 14, 2009 | Mitsubishi WS-55511 55" Rear Projection...

1 Answer

WS-55511 code 22.


Check these two green pico fuses F9A04 and F9A05 to see if they have continuity, if they dont have continuity the Convergence iC and those two picos will need replacement.

Jan 31, 2009 | Mitsubishi WS-55511 55" Rear Projection...

1 Answer

Mitsubishi 55 inch-ws 55511


23 code means "loss of Horizontal Deflection"

Nov 14, 2008 | Mitsubishi WS-55511 55" Rear Projection...

3 Answers

Please help me, i have Error code 23 on Mitsubishi WS-55511


A 23 error is loss of horizontal deflection First thing to check is the solder joints around the Flyback and around the two transformers T5A31 and T5A32. If you resolder those three items then pull the Q5A31 HOT ( Horizontal output transistor ) from circuit. If you send me a email to slinteriors@yahoo.com I will walk you through how to test the various components in the Horizontal deflection circuit and help you get your set up and running again.

Jun 24, 2008 | Mitsubishi WS-55511 55" Rear Projection...

1 Answer

WS-55511 Power Up problem


MOST LIKELY THAT CRT IS SHORTED. REMOVE THE CRT BOARD, (THE BOARD CONNECTED TO
THE CRT AND PLACE A SHEET OF CARDBOARD IN BETWEEN THE SOCKET AND CRT. THEN
TURN ON TV AND SEE IF SET COMES ON.

May 09, 2008 | Mitsubishi WS-55511 55" Rear Projection...

Not finding what you are looking for?
Mitsubishi WS-55511 55" Rear Projection Television Logo

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1210 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...