Question about Philips 19PR19 19" TV

1 Answer

Transistor lost. My philips tv model number 19E8007584 have a transistor lost, may be it explodes, and I would like to know if some one have the electric diagram and if coul tell me the transistor description. In the circuit board the number of piece of the transistor is 7402 in the power supply area. Thanks.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 240 Answers

If you are replacing 7402
also replace diode 6404 this diode even thou it test goo will in long term overheat 7404 and caus it to go bad by leakage.
and if 7402 gose bad it is regulating the 15v stanby volts that is 7412 is also going to be bad so replace 7412 also
now
the part numbers are:
7402 = # 932211676682

7412 =# 932210514682


thanks,
daniel.

Posted on Jan 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the number of a surface mounted device transistor in the powersupply of philips tv model 29pt2252/79?


There are lots of surface devices on a power supply. Can you be more specific or do you want a link to the schematic?

Aug 19, 2013 | Standard (CRT) Televisions

1 Answer

Diagram for psu transistor position 7521


Download the repair manual to this set by internet. It has all details.

Apr 27, 2013 | Standard (CRT) Televisions

1 Answer

I need to know the datasheet for the horizontal's transistor for a tv RCA 32F531T, because I lost the replacement


Hello
The number of horizontal output transistor is [TL 035]. If this number is not available, you can use exact substitute after reffering it to transistor data book and equivalents. OK.

Jun 03, 2011 | RCA 32F531T 32" TV

1 Answer

I have a magnavox model number 32mt3305/17 the green power light on the front panel is on but no sound or picture...just a black screen ...the fuse is good


You have lost your high voltage section, and that is why the TV is in shutdown mode, it has a horizontal output transistor that is shorted, and it is located on a metal heat sink near the fly back. You can have it repair if taken to the shop for about 100.

Jan 19, 2011 | Philips Magnavox 27MS343S 27" TV

1 Answer

My tv model 60P8341A philips television screen is red and dull in color what do i need to do?


Hello
If your TV screen looks more red its red video output section is in trouble. Some philips circuts uses transistors while others uses ICs in that section. Philips magnavox model have both types. We here in India, have transistorised video output stages in Philips Magnavox sets. Whatever the ciruit type may be, the fault and its remedy is same.
Check whether your set has transistors or ICs used. If transistors are used, check the collector voltage at red video output transistor. If ICs are used, some sets uses a single IC for Red, Green and Blue output stages. Some of them have three ICs on board as Red,Green and blue output stages.
The video output stages are integrated on the base card of your TV. That is, a small square or rectangular board, pluged into the neck of the picture tube. You just find out the red,green and blue output transistors, or ics whichever may be used. It is ver easy to understand the video output transistors. They may be a little larger than other transistors.
An easy way is to locate the Red,Green and blue cathodes of the picture tube base board points. Check the voltage of the three of them They must be almost equal to each other, provided a little, that is, 2 or 3VDC difference is allowable and will be. In your case, the voltage at the red cathode may be , not may be, must be low. As cathode voltage lowers, emmision of that cathode will rise, and poise that colour is in excess. If the Red Cathode voltage in your TV is found low, say difference betwwen other two cathodes is 50v or so, repace the red output transistor or the Ic if used at that stage. If a single Ic is used in your TV as R_G_B outputs, replce the same. If three Ics are there, replace the red output control Ic. ok
If you have any more problems, inform fixya. They will send me alerts.
Thank you

Oct 20, 2010 | Philips Magnavox 27MS343S 27" TV

1 Answer

Panasonic TV no sound no picture


THE REGULATOR IC STR ??? OR THE HOT TRANSISTOR MAYBE SHORTED

Aug 23, 2009 | Philips 27PT543S 27" TV

2 Answers

My tv fickers and shuts off ?


SYMPTOM:
Clicks and turns off after turning on set when cold. Have to turn on and off several times to work, or keep changing channels, right side of screen is black for a while.
PROBLEM: It is almost always a bad transistor and a bad capacitor. (about $0.70 in parts)
SOLUTION:
This repair is fairly straightforward. You will need a soldering iron, a solder ******, and a small torx bit. Unplug the set. Lay the TV on the floor, screen down. Remove the torx screws holding the rear cover on. There should be 10, (don’t forget the 2 by the input panel). You will see 2 circuit boards, the one of interest is the large one near the bottom of the set. This board has a retainer clip on each side that needs to be pulled out to allow the circuit board2.gif to slide out. Slide the board out about 5-6 inches. You might need to support the board so it doesn’t slide back down into the TV set. This circuit board should have numbers by each of the components. You want to look for 7461 (transistor) and 2455 (capacitor). They are located right next to each other near the center of the board. The transistor will usually overheat and discolor the circuit board immediately around it. Warm up the soldering iron and get the solder ****** ready. Heat up the solder joint while removing excess solder with the ******. Once the transistor and capacitor are free, check the numbers on each. The capacitor (round cylinder) should have “47uf” on it. The transistor should have “C33725” on it. You can order these parts from Digi-Key (google it) for about $2.50 including shipping if you use USPS option. The part numbers are: 493-1060-ND for the capacitor and BC33725-ND for the transistor. Once you get your parts, solder them in and check TV operation. It should work as it did before. This repair can be done by anyone familiar with a soldering iron in about 30-45 minutes their first time. Good Luck!!

Jun 28, 2009 | Philips 27PT543S 27" TV

2 Answers

Magnavox TV 25TS52 had power surge not working


You can call Magnavox customer support at this telephone number. 1-800-705-0000 Tell them the model number of your television and they will be able to help you. I hope this information helps you with your problem.

May 13, 2009 | Philips Magnavox 27MS343S 27" TV

1 Answer

Lost Manual


I have found it and you can click right here to read it or print it.

Hope this helps.
Richard

Mar 10, 2009 | Philips Magnavox 27MS343S 27" TV

Not finding what you are looking for?
Philips 19PR19 19" TV Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Standard (CRT) Televisions Experts

Sp Gupta

Level 3 Expert

667 Answers

yadayada
yadayada

Level 3 Expert

60541 Answers

Jim Evans

Level 2 Expert

186 Answers

Are you a Philips Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...