Question about Dishwashers

1 Answer

Drain pump never stop door opened or closed

One day the drain pump kept running and never stopped since .

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Thank you for answers, but i decided to buy a new one...

Posted on Jan 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bosch dishwasher shx46a06uc-30


the unit will try to complete the last command it was engage in before it went in the overfill safety mode. you must perform a cancel drain cycle to reset unit to default setting. Remember the drain cycle is 2 min and must be completed to reset main control. however if it went into a overfill status you have a leak and it generally comes from the pressure chamber on the lefthand side of unit where the water enters tub

Apr 17, 2012 | Bosch 24 in. SHX46A05UC Built-In...

1 Answer

Brand new SGS57A02GB just fitted. Run initial cleaning wash to get rid of factory water. Drain starts then stops, starts filling, goes through 2 filling cycles then the drain pump starts. The drain pump...


Hi,

This problem is mostly caused by the drain pump or a restricted drain line. Try taking the end of the drain hose off under the sink and re-checking the drain-out condition. If the unit is still not draining, I recommend replacing the drain pump.

Other possibilities could be that the sump is blocked, or the control or harness may need to be replaced.

Hope this helps.

Shane

Feb 01, 2011 | Bosch 24 in. SGS57E02 / SGS57E08 Exxcel...

1 Answer

Kitchenaid dishwasher won't drain someone opened door during cycle will this cause a problem


Opening the door wont matter. If you stop the cycle during a run it will always go into a drain. You might have a plugged drain line or burnt drain pump..

Apr 04, 2010 | KitchenAid KUDK03ITBK Built-in Dishwasher

1 Answer

Bosch SHU3036UC/U11 dishwasher does not stop filling with water


Hi,
It sounds as if the main program board has developed a fault - as it should come to a complete stop. The fact it kept the water valve open with the door open is a serious fault- so I would have it checked before using it again.

Most machines have a water-stop feature - so if it develops a leak - it will shut off the water. This clearly didn't happen.

Aug 05, 2009 | Bosch SHU3036UC Dishwasher

1 Answer

Bosch dishwasher runs w/door open. Wont stop pumping water out


That was exactly my issue-I've tilted it 45d, emptied the tray and it works!

May 25, 2009 | Bosch Integra® 500 SHX46A0 Dishwasher

1 Answer

My 501HT has stopped draining. It runs through a couple of cycles until the water inside builds up enough to leak out through the door. I have tested the cam switches #3 and #4 and they are opening and...


Hello Dabean
Have you sort out your problem yet if not please email me your problems and I try to sort them out for you my email address dickson@lau.com God Bless have a nice day Dickson

Mar 02, 2009 | Moyer Diebel 24 in. 501HT Built-in...

1 Answer

Kenmore dishwasher various problems


The portable dishwashers of the 70's and 80's often had one area of problem, and that was the pump getting jammed with debris and food.

To eleminate this problem, you will need to open up your dishwasher carefully, and drain all the water and gunk from your dishwashers rinse hose. I recommend taking the machine outside and use a low setting pressure hose (garden hose). With the hose off the rinse side, run the water through and see if it comes out of the pump's housing. Let it run for a few minutes.

The pump also has a switch that also goes with the run cycle. This switch thinks there is not enough water or it thinks it has done its job.

Sometimes replacing the timer helps, but first eliminate the lower hose situation first. If that doesn't help, you will need to then replace timer. If this doesn't help, most likely your pump is most likely jammed or malfunctioning.

May 24, 2008 | Dishwashers

5 Answers

The washer keeps beeping and trying to drain as soon as it is turned on


I have a Haier HDP18PA with the same problem... I tried tilting mine backwards while running...this made a mess BUT the beeping stopped BUT the lights were still flashing. Turned it off and started it again and the lights still were flashing BUT no beeping. Decided to try tilting it forward while running ... made another mess BUT the lights stopped flashing. Turned it off again and restarted it and it is now running fine. Good luck!

May 05, 2008 | Haier HDP18PA Stainless Steel...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...