Question about Dishwashers

1 Answer

Water coming into dishwasher when not running

When dishwasher is not running water from supply slowly fills machine casuing leaking if door not locked shut

Posted by on

  • willperk May 16, 2009

    Water slowly filling dishwasher cabinet when not running. Seems to be a slow leak from the inlet line. Is this a problem with a seal somewhere?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Removed intake water valve assembly and found a piece of plastic wedged in intake port preventing valve from closing. Piece of plastic was old filler tube from old hot water tank which disintegrated and got into hot water pipes in home. Similar pieces of plastic have affected water mixer valves at various sinks in home and have also plugged aeration screens.

Posted on Jan 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

LX30H THROWS A CODE EO after running awhile. I hit the high reset button under the flaps on the front for both the boost and reg elements . It will work for a couple cycles and then does the same thing....


Machine won't fill or won't fill high enough. site water pressure meets minimum flow pressures. (LX18, LX30 display shows working.
"E0," "E2," "E3," or "E4". LX40 display shows "DR1 PRBLM," "FILL1 PRBLM," FILL2 PRBLM," or "FILL3 PRBLM". Machine will not run.)

1. Low water pressure - check for clogged hose strainer; check that

2. Make sure probes are clean

3. No water pressure - main water supply valves may not be

4. Drain valve open - turn machine OFF to drain machine, then
ON. Repeat twice (this assists in clearing any drain valve
obstructions). Wait for machine to reach READY mode and
press WASH. Slowly open door several seconds later and note
water level. Close door; 30 seconds later, open door slowly and
check that water level is the same as it was. If not, repeat the
OFF-ON procedure. If problem persists, call your local Hobart
Service Office.

5. Delime machine.

https://my.hobartcorp.com/resourcecenter/ProductDocumentation/F18615%20Rev%20I.PDF

Dec 10, 2013 | Hobart Lx30h Commercial Dishwasher

1 Answer

Whirlpool ADP 4404/5 when left unused but connected to water supply it slowly fills up until it overflows and runs onto kitch floor, i.e while on holiday. I reckon it slowly fills to overflow in about...


Hello there and thank you for choosing fixya
Yes you are about right normally when the unit fills with water and you dont want it to this means that the water inlet supply valve has seals that are weak in it and the water is leaking bye it or the valve itself is failing or may even have debris in the valve keeping it from fully closing so you may want to pull the unit out and inspect the valve and you may even have to remove the outer panels to get to the valve to inspect it and some of them are even located under the left side as you look from the front of the machine ok so check these and if you need more help please post me a comment and i can further instruct you on repair procedures ok?
Hope htis is very help ful for you
Best regards fMike

May 25, 2011 | Whirlpool Gold 24 in. Built-In Dishwasher...

1 Answer

Have a GE hot point HSS25GFTABB, removed doors to put inside house after a move and the ice maker works, but when you fill with water, it runs down the line dripping at the bottom of left door


Inspect the line crefully at the bottom of the door where it connects to the cabinet supply. The line may have been damaged when and if the doors were removed.
HOPEFULLY it is a small nick in the tubing casuing the water leak, and not the line inside the freezer door as the water line is foamed into the door and the entire door would have to be replaced to resolve an internal leak.
The coupler at the door connection is a push-lock syle coupler and to seperate the line you need to press the white collar into the blue barrel connector to relese the tension.
Good luck!

Jun 14, 2010 | GE 25.0 Cu. Ft. Side-by-Side Refrigerator...

1 Answer

Water Pouring out of door, appliance stuck on wash


dishwasher leaking from the door or from the bottom of the door is common problem and yes its advisable to get it fixed.but if its having any other problem other then leaking then it has to be checked first.but leaking problem is common it can be solved.first from which part of the door area the leak is occuring that has to be checked.
Some common leaking trouble makers....
Leaks at the door:
Door gasket loose/torn
Corner gaskets or door baffle/vent gasket
Door lock/latch loose/broken
Split spray arm
Over filling with water...usually the level is just under the heating element is normal
Something leaking through the door...like the soap or rinse agent dispenser gasket, silverware basket button.
Door hinge(s) bent
Wrong soap was used...dish sink soap instead of dishwasher soap
Rinse aid being used with mechanically softened water ( makes foam or suds inside the dishwasher )

Leaks from under the unit:
Look for whiting or calcium stain on the motor and pump assembly = motor and pump assembly seal leak...access panel removal help
Hose for upper spray arm split
Fill hose split or fill hose spout air inlet is calcium covered
Drain hose is split
Rusted liner...metal liners only
Fill valve leaking or allowing water to fill all the time
Heating element ends....where they come out through the dishwasher liner
Float or float gasket
for parts you can get it from
www.repairclinic.com

Nov 21, 2009 | Candy Dishwashers

1 Answer

At some point the dishwasher leaks onto the floor. what could be the possible problem?


this are the possibilities for the leak :-----
Door gasket loose/torn
Corner gaskets or door baffle/vent gasket
Door lock/latch loose/broken
Split spray arm
Over filling with water...usually the level is just under the heating element is normal
Something leaking through the door...like the soap or rinse agent dispenser gasket, silverware basket button.
Door hinge(s) bent
Wrong soap was used...dish sink soap instead of dishwasher soap
Rinse aid being used with mechanically softened water ( makes foam or suds inside the dishwasher )

Leaks from under the unit:
Look for whiting or calcium stain on the motor and pump assembly = motor and pump assembly seal leak...access panel removal help
Hose for upper spray arm split
Fill hose split or fill hose spout air inlet is calcium covered
Drain hose is split
Rusted liner...metal liners only
Fill valve leaking or allowing water to fill all the time
Heating element ends....where they come out through the dishwasher liner
Float or float gasket.

Sep 23, 2009 | Whirlpool 24 in. GU980SCG Built-in...

3 Answers

Leaks water from bottom of door. Error code E7 ?


I found this and it also may have to do with the door seals...how old is the unit...if door seals get old and stiff..(not soft and pliable) they sometimes leak...after usage the heat and moisture may cause them to swell and or become soft thereby sealing better...but this is what I found in the user manual.

Machine displays "E7" on LX30 model or "CLEAN PROBE" on LX40 model.
1. Clean water sensors inside tank.
It suggests contacting Hobart if this fails but I also found this problem is associated with fill issues...as in an E4 error...this what you do in that case....

Machine won't fill or won't fill high enough(LX18, LX30 display shows "E0," "E2," "E3," or "E4")

1.Low water pressure — check for clogged hose strainer; check that site water pressure meets minimum flow pressures.
2.Make sure probes are clean.
3.No water pressure — main water supply valves may not be working.
4.Drain valve open - turn machine off to drain machine, then on. Repeat twice (this assists in clearing any drain valve obstructions). Wait for machine to reach READY mode and press WASH. Slowly open door several seconds later and note water level. Close door; 30 seconds later, open door slowly and check that water level is the same as it was. If not, repeat the
OFF-ON procedure.
5. Delime machine.

Good Luck and I hope this helps...let me know if it doesn't and i am sure I can get to the bottom of it...thanks for rating my effort...the Fang.

May 19, 2009 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

E4 error after attempting to fill and get to temp


This is what I found for the E4 code...hope this helps...and thanks for rating my effort...The Fang.


Machine won't fill or won't fill high enough(LX18, LX30 display shows "E0," "E2," "E3," or "E4")

1.Low water pressure — check for clogged hose strainer; check that site water pressure meets minimum flow pressures.
2.Make sure probes are clean.
3.No water pressure — main water supply valves may not be working.
4.Drain valve open - turn machine off to drain machine, then on. Repeat twice (this assists in clearing any drain valve obstructions). Wait for machine to reach READY mode and press WASH. Slowly open door several seconds later and note water level. Close door; 30 seconds later, open door slowly and check that water level is the same as it was. If not, repeat the
OFF-ON procedure.
5. Delime machine.

Apr 28, 2009 | Hobart 24 in. LXIH-3 Built-in Dishwasher

2 Answers

Hobart LX15H indicates E4 and will not fill.


This is what I found in the manual...and on a couple of other sites....

Machine won't fill or won't fill high enough(LX18, LX30 display shows "E0," "E2," "E3," or "E4")

1.Low water pressure — check for clogged hose strainer; check that site water pressure meets minimum flow pressures.
2.Make sure probes are clean.
3.No water pressure — main water supply valves may not be working.
4.Drain valve open - turn machine off to drain machine, then on. Repeat twice (this assists in clearing any drain valve obstructions). Wait for machine to reach READY mode and press WASH. Slowly open door several seconds later and note water level. Close door; 30 seconds later, open door slowly and check that water level is the same as it was. If not, repeat the
OFF-ON procedure.
5. Delime machine.

If this doesn't help let me know and I will get to the bottom of it....good luck and thanks for rating my effort...The Fang.

Apr 27, 2009 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

While not in operation dishwasher slowly fills up.


water valve is clogged try to turn your valve to dishwasher under sink

Nov 29, 2008 | Kenmore 16602 / 16604 / 16609 Built-in...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

yadayada
yadayada

Level 3 Expert

70346 Answers

Brad Brown

Level 3 Expert

15100 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...