Question about Pioneer VSX-43TX 7.1 Channels Receiver

Open Question

Pioneer elite vsx-43tx power surge_wont power up.

Wont power on after possible surge. Red light just blinks slowly.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Pioneer power LED is Blinking

If that didn't work, with the power off try holding Tune + and Auto surround/stream direct buttons for a few seconds to reset the protection circuits. Make sure to keep 8" of empty space above the unit for air, as overheating can cause this problem. If it fails again, there could be bigger problems, so get it checked

Posted on Jan 24, 2010

Ad
  • 1 Answer

SOURCE: Flashing Red MCACC Light

hold the tune down (-) button and multi zone on/off button for two seconds then receiver should reset on the VSX-1019AHK model!!!

Posted on Nov 08, 2010

  • 1 Answer

SOURCE: vsx-815 steady blinking blue light

Hold "Enter" and "Advnc. Surrnd" buttons on receiver at the same time.

Posted on Mar 16, 2008

  • 1 Answer

SOURCE: MCACC Light Blinking and reveiver

If you hold ENTER + VIDEO 2 for 2 or 3 seconds it should work ... not a factory reset so proceed at own caution!!!

Posted on Jul 05, 2008

  • 4 Answers

SOURCE: Pioneer VSX-816

With the receiver off, press ENTER + ADVANCED SURROUND keys continuously for 2 sec. and it will tell you the fault it encountered. Even if it has a short, it will still protect the speakers; however, it is still a good idea to disconnect all speakers before doing this.

Posted on Aug 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 56 in hdtv Panasonic tv will not come on green light flashes 20 times then goes to red. Help, on disability fixed income & cant afford to get repair or new tv. Please help, as soon as poss


Panasonic Plasma TV Repair - Understanding 14 Blink ...

? 8:35
https://www.youtube.com/watch?v=iHBIiRxhe0w
Sep 26, 2014 - Uploaded by ShopJimmy.com
Panasonic Plasma 14 Blink Code Explained with Repair Info How to ... I guess I'll try the SC board and if that does not work simply save up for a new ... The red power led was flashing 12 timespause a few seconds then flash 12 again. ... It powers up and shows the green power light is on, but there's no ...

The power light keeps flashing and the tv wont turn on - TV ...

www.tomsguide.com/answers/id.../power-light-flashing-wont-turn.html
Oct 24, 2015 - More about : power light flashing wont turn ... December 20, 2013 10:12:55 AM ... sound like it is coming on then it shuts off and the red power light flashes slowly. ... 50in Plasma tv power light is flashing 8 times and won't turn on. ...tv to come on bcause the power button keep blinking my tv will not come on.

Nov 06, 2015 | Panasonic Televison & Video

1 Answer

Sony KDL 46HX820 turns on, then off and red light blinks four times.


Re: Bravia KDL46EX720. Red LED blinks 4 times and TV wont turn on. What is the problem?

Do a Power Reset.

1. Turn off the TV.
2. Unplug the power cord of the TV from the electrical outlet.
3. Let the TV remain without power for 60 seconds.
4. Plug the power cord back into the electrical outlet. (If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.)
5. Turn on the TV.

If the issue still persists after performing power reset, that may be an indication that the TV needs service. You may refer to this link to locate the nearest Sony authorized service center in your area.

Oct 21, 2014 | Sony KDL-46HX820 - 46" BRAVIA 1080p LED...

2 Answers

I have a blicking red light and no picture ?


Possible power supply damage. Remove the power lead, wait 10minutes and try again.

Jun 26, 2014 | Panasonic VIERA TH-42PX60U 42 in. Plasma...

2 Answers

Pioneer VSX-72TXV wont power up. mcacc light just blinks.. unit does not have a video 2 button on the face.


try holding the "TUNE -" button and the ZONE 2 on/off button and see if it turns on. If its turns on, but turns back off again, you either have a problem with your speakers (try disconnecting them) or there is a problem with the receiver that needs to be repaired.

Dec 06, 2013 | Pioneer VSX-72TXV Receiver

1 Answer

Stereo wont turn on only red light is blinking


It sounds as if you are lacking accessory power to the unit. Insure that the red wire of the Pioneer unit is receiving 12 volts with the key in the accessory and on position.

May 05, 2011 | Pioneer AVH-P5700DVD Car DVD Player

1 Answer

RED LIGHT KEEPS BLINKING..WAS LIKE A POWER SURGE THIS MORNING..I UNPLUGED TV OFF MOSNTER SURGE PROTECTOR..CAME HOME AND PLUGED BACK IN...TV RED LIGHT TV REC STILL BLINKING


Surge protectors aren't perfect... If the surge was big enough and long enough then it can cause problems. Most manufacturers have on-board protection as well. That's not perfect either. Often the surge does nothing more than confuse the microprocessor (computer) that controls all aspects of your television. The fact that the red light is blinking means that your set is trying to protect itself. This can happen for one of two reasons. Something in the set has failed. Usually the power supply inside the set possibly also a trouble in the scan section of your set. These are normally a shop repair. The other thing is when the microprocessor is confused it will do nothing further until it's reset. To reset the processor simply unplug the set from the wall and wait 10 minutes. Plug it back in and if it works then happy viewing. If it doesn't then you will need a repair.

If is a failure caused by a failure in the grid that delivers power to your set then you are usually able to file a claim for the repairs. Contact your local power company. explain what happened. If it's their fault then usually they will pay for a repair. I know the PG&E does.

Zashiban

Jun 23, 2010 | Toshiba 42LX196 42 in. LCD HDTV

3 Answers

Pioneer VSX-1019 with a flashing red MCACC


you can "release" the error by pressing the "down arrow" and the "zone 2 on/off" for 2 seconds.

Mar 11, 2010 | Pioneer VSX-1019AHK A/V receiver

Not finding what you are looking for?
Pioneer VSX-43TX 7.1 Channels Receiver Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5190 Answers

John
John

Level 2 Expert

509 Answers

T-Comtech Repairs
T-Comtech Repairs

Level 2 Expert

417 Answers

Are you a Pioneer Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...