Question about Ariston Technologies Ariston AWD12 Front Load Washer/Dryer

Open Question

Hi, Ariston LSE 730 T dishwasher displays an error code A08 and has left the washing powder in the dispenser stuck solid. Do you know what this means? Thank you for your advice, Judy

Posted by on

  • judysza Jan 16, 2009

    A08 error code is caused by the NTC heat sensor. In my case the detergent (Calgonit) caused it by producing too much foam. Luckily there was nothing wrong with the electronics of the dishwasher. The spare part would have cost half the original price of the dishwasher. Ask your expert which is the best detergent for your dishwasher and avoid Calgonit..

×

1 Suggested Answer

  • 160 Answers

SOURCE: Ariston LSE 730 T dishwasher displays an erro ao1

A01 means The micro-switch in the base tray has been closed for 9 seconds to signal the alarm.
Water is leaking from components or hoses in the base of the machine.
Programme will abort and the drain pump will be energised.

Posted on Dec 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fabric Softener Does Not Drain


25569074-ineink0kisfnom0atbkujjcx-3-0.jpg
compartment 1: Detergent for pre-wash
(powder)

Before pouring in the detergent, make sure that extra compartment 4 has been removed.

compartment 2: Detergent for the wash cycle
(powder or liquid)

Liquid detergent should only be poured in immediately prior to the wash cycle start.

compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow from the grid.

extra compartment 4: Bleach
! Do not use Hand Wash Detergent because it may form too much foam.

Cleaning the detergent dispenser
Remove the dispenser by raising it and pulling it out (see figure).
Wash it under running water; this operation should be repeated
frequently.

25569074-ineink0kisfnom0atbkujjcx-3-1.jpg 25569074-ineink0kisfnom0atbkujjcx-3-3.jpg 25569074-ineink0kisfnom0atbkujjcx-3-6.jpg
Dado

Mar 14, 2015 | Ariston Technologies AW125NA 13 lbs. Load...

1 Answer

Leaks from front left corner but only on certain washes and only a small amount


hello have you checked the door seal they tend to get holes in them. or the plastic powder dispenser check the hoses hope it helps

regards
shaun

Mar 06, 2011 | Hotpoint Ariston Aquarius WD420 Front Load...

1 Answer

Why does a lot of detergent remain in the soap dispenser after a washing cycle is complete


Was the dispenser cup wet when you added detergent?
Make sure the dispenser cup is dry before adding powdered detergent. If dispenser cup is wet, the detergent can clump.
Is the cycle incomplete?
If the previous cycle did not complete, the detergent can become caked in the dispenser cup if it is left sitting in the dishwasher.
Is the detergent old?
Older detergent exposed to air will clump and not dissolve well, which will cause the dispenser door to stick to the detergent. Replace detergent if necessary and store the detergent in a tightly closed container in a cool dry place.
Is the water temperature too low?
For best washing and drying results, water should be 120oF (49o C) as it enters the dishwasher.
Were items blocking the dispenser that kept it from opening?
Items blocking the detergent dispenser will keep it from opening. Make sure water action can reach the dispenser.
Detergent guidelines
  • Use automatic dishwashing detergent only.
  • Other detergents can produce excessive suds that can overflow out of the dishwasher and reduce washing performance.
  • Store tightly closed detergent in a cool, dry place.
  • Fresh automatic dishwasher detergent results in better cleaning.
  • Add detergents just before starting the cycle.
  • The amount of detergent to use depends on the hardness of your water and the type of detergent.
  • If you use too little, dishes won't be clean.
  • If you use too much in soft water, glassware will etch.
  • Suggested fill amounts are for standard powdered detergent. Amounts may vary if you use liquid or concentrated powdered detergent. Follow instructions on the package when using these detergents.
  • Water hardness can change over a period of time. Find out your water's hardness by asking your local water department, water softener company, or county extension agent.

Nov 25, 2010 | LG Washing Machines

3 Answers

My Haier HW-C1460TVE-U washing m/c keeps giving (CLrF) ERROR Code


Anyway, my machine shows an error code "clrf". I just spoke to someone at Comet, and apparently this means there is too much foam in the machine. The machine will then refill with water and try to rinse it out, but if after that the machine still has too much foam in, then it will stop the cycle. Hence why my clothes are still wet (although I'd not realised they weren't rinsed properly either!).

I have not been using excessive amounts of washing powder, and usually use powder tablets or the liquid tablet sort, so they are a set amount and I don't do anything daft like stick 6 tablets in! I find it ridiculous that this would cause a problem with the washing machine, as I've used them perfectly fine with other washing machines.

Anyway, the advice from Comet was to keep trying different washing powders until i find one that foams less.

Jan 07, 2010 | Haier Washing Machines

1 Answer

Ariston LSE 730 T dishwasher displays an erro ao1 watt is this?


A01 means The micro-switch in the base tray has been closed for 9 seconds to signal the alarm.
Water is leaking from components or hoses in the base of the machine.
Programme will abort and the drain pump will be energised.

Dec 21, 2009 | Ariston Technologies Washing Machines

1 Answer

The machine doesn't start! The led pause/start is blikkering green or yellow, but I can't get the machine working


1) Ensure the dishwasher is turned off. 2) (may not apply) Turn the plastic blue lever located under the sink to the vertical position (this opens the valve, so water can go into the dishwasher) 3) Pour powder indo the dishwasher 4) Turn the dishwasher controller to the top position (the 12 o?clock position) ? this is the eco-setting. 5) Press the on/power button on the dishwasher, so that it now turned on (a light will display) 6) Move the dishwasher controller to the ?R? position (it?s on the very left), and leave it there a second or two. 7) Move the dishwasher controller back to the eco-setting (the 12 o?clock position).

Dec 03, 2009 | Ariston Technologies AW125NA 13 lbs. Load...

1 Answer

F-08 is on the display


Error code F08 indicates heater relay stuck.
  1. Check pressure switch connections.
  2. Check heater connections.
  3. Check module connections.
  4. Check and clean pump and or pump filter.
Please rate my solution.
Thanks.

Nov 15, 2009 | Ariston Technologies AW125NA 13 lbs. Load...

1 Answer

Hi, my dishwasher type ariston LI 420 does not drain.the led 1 and 2 from left side blinking. Can you suggest me somethings. there's a file with the error led code to consult. Thanks' in advance


you might have a blockage in your filter or in the pump,first i would find out where your waste pipe goes out to if it is plumbed out through ur sink take the hose off and hold it in a bucket and turn the unit on you should hear a sucking sound and if the does now drain then have a look in the sink waste trap it is very common for the sink waste to get blocked

Oct 21, 2009 | Ariston Technologies LI640S Dishwasher

1 Answer

Hi zanussi fjr 1254 w error code e90 what does


This error code seems to be the control board detecting a wrong configuration (in other words, an illogical set of sensing conditions, from its connected sensors and wiring). It apparently can happen, when wires become badly contacting, or if contaminated with motor brush carbon (the horrible black powder that comes off the motor commutator and brushes), or corroded from other contaminants from the soap dispenser area. You should be able to check this, remove, clean and replace the contacts:
Thanks

Jul 01, 2009 | Zanussi Washing Machines

1 Answer

Ariston Dishwasher LI 675 DUO


1) Ensure the dishwasher is turned off.
2) (may not apply) Turn the plastic blue lever located under the sink to the vertical position (this opens the valve, so water can go into the dishwasher)
3) Pour powder indo the dishwasher
4) Turn the dishwasher controller to the top position (the 12 o’clock position) – this is the eco-setting.
5) Press the on/power button on the dishwasher, so that it now turned on (a light will display)
6) Move the dishwasher controller to the “R” position (it’s on the very left), and leave it there a second or two.
7) Move the dishwasher controller back to the eco-setting (the 12 o’clock position

Sep 16, 2008 | Ariston Technologies LI640S Dishwasher

Not finding what you are looking for?
Ariston Technologies Ariston AWD12 Front Load Washer/Dryer Logo

Related Topics:

1,143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ariston Technologies Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you an Ariston Technologies Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...