Question about Intel Motherboard

1 Answer

After i install the new motherboard, and i hit the power button, the screen monitor is not on and my heard the long beep sound from my motherboard. i check all the wire is ok but i dont know what wrong? please help me if you could, thank you

Posted by on

  • Jason Edinger May 11, 2010

    What brand is the motherboard? Or what make/model is the pc?


  • Shawn McGuire
    Shawn McGuire May 11, 2010

    How many beeps are there? Are they long? short? A little more info and I'll be able to tell you what the beep codes mean.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 53 Answers

You may need to try a few steps here,

1. Switch of you pc and open up you pc cover.

2. Pull out the memory (RAM) from the slot by pressing down the clipsfrom each edge, be gentle will you push down the clips from each side.Remember how it was seated when u pull out.

3. After that, put re-seat back the RAM back to the slot by pressing each edges in, firmly but not with excessive power.

4.Try to switch on the pc after you re-seated the RAM. If no success, youhv to repeat the procedure again, but this time clean the RAM's contactwith a cloth and contact cleaner, then re-seat it back and try again.

*here's the instruction with diagram to show you how to do it.

and video as well

5.If still no sign of success, you might have to unplug other cards, suchas your video card, and re-seat them back, then try again.

6. Worst case scenario, disassemble your motherboard and test it without fixing in the chasis by fising only your power supply, RAM, Video Card, Keyboard, and see if it works.



Good luck mate, comment here to let me know the progress or any success.

Do remember to rate my solution.. thanks (^_^)

Posted on Jan 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No display after reboot windows


If it seems like your system is running whereas you hear fans running, hear the hard drive running, see lights, heard the hard drive click during bootup, but there is nothing on the lcd screen then try the following:
1) Try hooking a external monitor to your laptop. It can be any type of monitor even one of the old style fat crt monitors as long as it has a vga cable to connect to the laptop. There is a sequence of keys you might have to hit to get the display to show on the external. Most times you hit the FN (Function key) and hold it while you hit the corresponding F1 thru F12 key that is for display. Usually the correct key will say CRT/LCD or it might have a display icon on it. If the image displays on the external monitor that means the video card is good.
2). Remove the external monitor and reboot the computer again. Now when it is done booting take a flashlight an shine it on the lcd screen. You are looking to see if you can faintly see the icons on the screen. If they are there but barely visible then the LCD Inverter is bad. The LCD Inverter is located at the bottom of the lcd screen just above the keyboard and the Strip around the lcd screen covers it. You'll have to take the lcd apart to get to it.
3) If you don't see anything when you shine a flashlight on the desktop, then the lcd screen has to be replaced. However, sometimes the cable on the back of the lcd screen has come aloose or just needs reseating, so unplug the cable and put it back then see if it shows an image.


Read Below if it is not booting at all when you press the power button.
Laptops don't boot for the following reasons: 1) Bad Power Cord. 2) Bad DC Power Jack where the power cord plugs into the laptop. 3) Static Charge Buildup. 4) Bad Motherboard.

The above 4 reasons are when you press the power button and absolutely nothing happens. You hear no fans running, no disk drive running, no one time clicking sound on the CD Drive and No light for a second or two when the CD drives click. In the case of a motherboard issue sometimes you will hear beep sounds or see blinking lights. Those beep sounds and blinking lights tells the technician what is going on with your motherboard and why it will not boot. If you see the blinking lights or hear beeps count them.

So you have a power light which means your power cord and dc power jack is good. So lets see if you have a static charge buildup.

Remove the Power Cord and the Battery from the laptop, then Press and Hold the Power Button for 30 seconds. After 30 seconds put the power cord back into the laptop, but leave the battery out. Press the power button to see if it boots. If it does you had a Static Charge Buildup and it's ok to put your battery back in. If it does not you more than likely have an issue with your motherboard.

Mar 23, 2012 | Computers & Internet

1 Answer

How to solve problem after reboot my notebook dell no displaY


If it seems like your system is running whereas you hear fans running, hear the hard drive running, see lights, heard the hard drive click during bootup, but there is nothing on the lcd screen then try the following:
1) Try hooking a external monitor to your laptop. It can be any type of monitor even one of the old style fat crt monitors as long as it has a vga cable to connect to the laptop. There is a sequence of keys you might have to hit to get the display to show on the external. Most times you hit the FN (Function key) and hold it while you hit the corresponding F1 thru F12 key that is for display. Usually the correct key will say CRT/LCD or it might have a display icon on it. If the image displays on the external monitor that means the video card is good.
2). Remove the external monitor and reboot the computer again. Now when it is done booting take a flashlight an shine it on the lcd screen. You are looking to see if you can faintly see the icons on the screen. If they are there but barely visible then the LCD Inverter is bad. The LCD Inverter is located at the bottom of the lcd screen just above the keyboard and the Strip around the lcd screen covers it. You'll have to take the lcd apart to get to it.
3) If you don't see anything when you shine a flashlight on the desktop, then the lcd screen has to be replaced. However, sometimes the cable on the back of the lcd screen has come aloose or just needs reseating, so unplug the cable and put it back then see if it shows an image.

Read Below if it is not booting at all when you press the power button.
Laptops don't boot for the following reasons: 1) Bad Power Cord. 2) Bad DC Power Jack where the power cord plugs into the laptop. 3) Static Charge Buildup. 4) Bad Motherboard.

The above 4 reasons are when you press the power button and absolutely nothing happens. You hear no fans running, no disk drive running, no one time clicking sound on the CD Drive and No light for a second or two when the CD drives click. In the case of a motherboard issue sometimes you will hear beep sounds or see blinking lights. Those beep sounds and blinking lights tells the technician what is going on with your motherboard and why it will not boot. If you see the blinking lights or hear beeps count them.

So you have a power light which means your power cord and dc power jack is good. So lets see if you have a static charge buildup.

Remove the Power Cord and the Battery from the laptop, then Press and Hold the Power Button for 30 seconds. After 30 seconds put the power cord back into the laptop, but leave the battery out. Press the power button to see if it boots. If it does you had a Static Charge Buildup and it's ok to put your battery back in. If it does not you more than likely have an issue with your motherboard.

Mar 23, 2012 | ASUS Eee Computers & Internet

1 Answer

My FP 7317 monitor power doesn't work.When I open it,I heared beep sound frequintely.can you help me/


Good Day Gmariamd!

A beep codes has different meaning. Depending on the number of beeps and the series of short or long beeps.

But most frequently, a beeps were heard when a video card and or memory card is loosened. You may need to remove it from the motherboard and reseat them properly on the slot of the motherboard. Just remember when you do it computer must be off.

Jun 12, 2011 | Compaq FP 7317 17" LCD Monitor

1 Answer

No input signal


that is the problem of cpu not a monitor to confirm disconnect signal cable and power on. monitor will show "no signal check signal cable" it means that monitor is ok and fault lies in cpu .then open the cpu and disconnect ram and listen the beep. contineus beep should be heard then ram is faulty replace it. if no beep heard then motherboard is faulty .

Mar 08, 2010 | HP vs17

1 Answer

I get nothing on the monitor when it starts up!!!!


I assume you have had the side panel off to watch the cpu fan spin up? if it does spin up and you get no bios beeps, then the fault is with the motherboard or CPU, most probably the motherboard. Problem sounds like capacitors blown or leaking ( have a look at the board and see if any are bulging or leaking). I've had similar issues with the motherboards that HP use, in all cases it was the motherboard at fault

Feb 12, 2010 | HP Compaq Presario SR2170NX (RK549AA#ABA)...

2 Answers

Blank screen upon startup


Try taking out the hard disk, plug in power and see if you have a display on your screen or external monitor. if same thing happen, try taking out the memory card. If you hear a beep sound it's a faulty mem. card, if no beep sound appears I suspected it's a motherboard faulty.

May 31, 2009 | Lenovo ThinkPad T61 Notebook

2 Answers

Black screen


Ensure that the power button is pressed and the monitor is plugged in correctly. If ok, then the installation was stopped while installing your video drivers. If possible use another monitor to re-load the xp operating system until completed. Once the video monitor drivers are loaded the monitor will work again. Let me know if you have any questions.

Don't forget to rate this solution before you log off.

Jan 26, 2009 | Compaq Presario S4020WM PC Desktop

2 Answers

No output


if you are using pci or pci-e the motherboard maybe bad on the driver slots,if using the onboard system on the motherboard it is out and needs replaced. lala linda

May 31, 2008 | Biostar P4M80-M4 Motherboard

1 Answer

No booting


did u chk the power cable to monitor ?
replace the power cable wd tht of the tower or cpu if cpu glows then ur monitor neds to be repired

May 22, 2008 | Intel Motherboard

4 Answers

My Computer does not boot


please check whre u have connected ur monitor comm cable, is it in agp card or on borad display card

Apr 21, 2008 | ASUS M2N-MX Motherboard

Not finding what you are looking for?
Intel Motherboard Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Intel Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Tony

Level 3 Expert

2598 Answers

David
David

Level 3 Expert

778 Answers

Are you an Intel Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...