Question about Kodak EasyShare V610 Digital Camera

1 Answer

Error 45 it does nTt work and only shoe the erroe

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Kodak Master
  • 1,019 Answers

Hello, The error code 45 indicates that the camera needs service/repair. You need to take it to a camera shop for them to determine the problem.

Best Regards, Russell

Posted on Jan 24, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What is the cause of OKI C3200n fatal error 173

Fatal error code 173:
This error indicates that the Image Drum Up/Down Process is not working properly. The errors are as follows:
140 - Yellow Drum Up/Down error
141 - Magenta Drum Up/Down error
142 - Cyan Drum Up/Down error
1. Reseat the Image Drums. Ensure they are in seating properly into the drum carriage.
2. Reseat the Toner Cartridges. Ensure they are seating properly into the Image Drums.
3. Reseat the Contact Sensor Spring assembly and inspect it for damage or mis-alignment. If the springs appear bent or dis-lodged reseat them.

Aug 12, 2014 | OKI C3200n Led Printer

3 Answers

On my Samsung S3500 when trying to reply to a text message it says memory full. My memory card has lots of memory on it though.

you have to erase or move apps and video,images,ext. to memory card you have the phones full memory not the sd card.

Jun 25, 2011 | Samsung S3500 Cell Phone

2 Answers

My car went in for body work due to accident. When I picked it up the check engine light was on. I took it back, they hooked it up and told me they cleared it but it showed that the "Bank one...

Do you actually feel a miss? If not, it could be an open or short caused by either the accident or the repair. If the light didn't illuminate before you had the repair done, it is very possible something is amiss as a result of the repair. If you can feel the engine missing, start it when it's cold and let it run for 15 or 20 seconds then shut it down. Feel the exhaust manifolds. The manifold will be cooler corresponding to the cylinder that is missing. It could be a connection to the coil pack on that cylinder or even a bad coil pack.

Jun 24, 2011 | 2008 Chevrolet Impala

2 Answers

Where is the blower motor resistor located on a 2001 Daewoo leganza

Right next to the blower motor as the big wire coming out of the motor goes right to it.

Jun 24, 2011 | 2001 Daewoo Leganza

10 Answers

Where can convert european shoe sizes to american?

Here you may find a convertion table for shoe sizes.

Oct 27, 2010 | Clothing Accessories

1 Answer

Metz 45 cl-1 speed light & nikon d60

If the shoe of the flash is compatible with the hot shoe of the camera then yes go for it. Should the flash shoe be different then the flash will still work but with a shoe adapter. Both are TTL so I see no reasons why they won't work. I do know of a friend who uses the Nikon with the same flash but it has the battery pack fitting and uses an adapter on the camera's hot shoe. He does weddings galore and never had a problem even though he carries a spare he has never used it.

Apr 22, 2010 | Nikon Speedlight SB-80DX TTL Flash

3 Answers

My Precor C956 treadmill reads erroe code 45. what does this mean and what can I do?

Error 45, Lift Moving in Wrong Direction It maybe the lift motor itself the potentiometer maybe defective, the ribbon between upper and lower boards

Feb 27, 2010 | Precor C954i Commercial Treadmill

2 Answers

Metz mecablitz 45 ct 1 and Nikon D-90

The trigger voltage of the 45CL-1 is about 12V, so it should be safe to connect directly to the hot shoe with an adaptor, or to the pc soclet, if the D90 has one. If the D90 is anything like my Canon 40D, which can stand about 30V on the hot shoe, then all the 45CL series will be ok, as they have trigger voltages between 9V and 12V. The 45CT-5 has a trigger voltage of 15V and works well on the 40D. I use 3 different Metz 45 models with my 40D and all work well on automatic, where the flash sensor itself controls the light output.

Jan 26, 2009 | Metz 45 CL-1 Flash

2 Answers

Error code F2-45

Ihave Sharp AR-C160. WHAT DOES THIS H4-01 ERRO CODE MEAN? How do I clear it?

Jul 18, 2008 | Sharp AR-C160 Color Copier

Not finding what you are looking for?
Kodak EasyShare V610 Digital Camera Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kodak Cameras Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1689 Answers

Computer Links

Level 3 Expert

2386 Answers

Are you a Kodak Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides