Question about Samsung WF337AA Front Load Washer

1 Answer

FL code Won't start, makes a popping sound.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Samsung Master
  • 9,472 Answers

The "FL" code indicates that the failed to lock the door, which would prevent the machine from running. You will need to replace the lock. Here is the part to order. Below is a video to show you how to replace it.



Posted on Dec 09, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code FL-maytag neptune front load washer won't lock


replace door latch (fl = faulty latch ) good luck APPLIANCES R EN

Mar 09, 2013 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Wont start


There is no sound to flooding &
there is no vapor lock in over 30
years, since all vehicles are fuel
injected & the fuel either continually
flows back to the tank or deadheads
to fuel rail & is used

You either have fuel pressure or
it is too low or not there or pump
drains down when turned off

You obviously need a good battery,spark
plugs & functioning ignition system (spark)

Will have to be tested to see what your missing

Could be you have a stored code if the electronics
are checked first.

You need to provide a vehicle,year,make,engine,etc
& some detail of any problems,plus any testing done

Won't Start --- won't get you an answer or a quess

Nov 16, 2012 | Cars & Trucks

1 Answer

Car won't start. Gages bounce quickly & make a clicking sound on 2006 ford taurus


check your battery,or not clean battery terminals,or starter motor solenoid.

Aug 22, 2012 | 1993 Cadillac DeVille

1 Answer

1993 nissan pick up won't start


Possibly a bad connection on the positive side coming from the battery or a weak ground. Check where the leads join the terminal clamps. Has the battery been verified as good? It doesn't take a lot of amps to run lights but it does to turn over the engine. Jump starting it does not require a fully charged battery.

May 01, 2017 | 1993 Nissan Pickup

1 Answer

2005 sedona won't start all of a sudden. Doesn't make a sound except for a tiny whirring sound like the feul injectors. Replaced starter...still won't start. checked all fuses...they are good....


you could just have dead cell in the battery which isn't getting enough amps to the starter,, have the battery LOAD checked,, that will tell you if the battery is actually good, just because it registers 12 volts isn't necessarily an indication that the required amps are present.

Sep 27, 2011 | 2005 Kia Sedona

1 Answer

Yamaha htr-5840 won't work with comcast remote codes, tried all codes, nothing will work, remote is Comcast dvr 3 device


I have a Yamaha RX-V571 AV Receiver and the published codes don't work for my Comcast silver remote w/ Red OK button. Managed to make it work while living in MD. Now in FL, have new remote and don't remember how I made it work before. Would love some help. T Y

Sep 19, 2011 | Yamaha HTR-5840 Receiver

1 Answer

MY 2002 DODGE GRAND CARAVAN, 3.3 started out by stalling. we took it for diagnostic, mechanic said catalytic convertor bad. changed that and coil. changed map sensor, both O2 sensors. took it to another...


does the van stall going down the road or at idle? the won't change gears at 4000 rpm and the no start condition unless disconnect the negative cable sounds more like a computer problem. when the cable is diconnected the ECM and the TCM have to go thru a relearn process which can be some of your issues. have your mechanic do a quick learn on the trans module to see if it helps the shifting problem. the ECM on the other hand can throw out codes that can make you chase your tail and end up replacing every sensor and still have the smae problem. you may want to check for corrosion at the ECM connections.

Jul 19, 2011 | Dodge Grand Caravan Cars & Trucks

1 Answer

Error code FL flashes and my calypso washer keeps beeping. Won't start just shows the code.


FL error - Flood condition

"FL" flashes if any overfill condition occurs. This condition occurs when excessive water in the tub causes the overfill switch to trip. The control must realize that the trip was due to an overfill condition instead of a suds lock condition in order for "FL" to be displayed.

With an overfill condition, the beeper repeats a warning every 10 seconds with no time out. The pump is cycled in drain mode for 30 seconds on, 30 seconds off until the overfill switch resets or power is discontinued to the unit. Press STOP/CANCEL to clear the display.

You coudl se this manual: Service_Manual_PDF

Hope this helps.

May 20, 2011 | Whirlpool Calypso GVW9959K Top Load Washer

Not finding what you are looking for?
Samsung WF337AA Front Load Washer Logo

533 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Washing Machines Experts

Jaime Hernandez

Level 3 Expert

2318 Answers

shaun taylor

Level 3 Expert

1525 Answers

The Knight
The Knight

Level 3 Expert

74185 Answers

Are you a Samsung Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...