Question about Blomberg Washing Machines

1 Answer

The error message "door" is displayed and the machine won't start. I can I reset it.

Posted by Anonymous on

  • Joe Worker
    Joe Worker Mar 11, 2016

    I have Blomberg WM87120 NBL00 Product code 717518110 and had flashing Lock in display. Bought and installed new lock and no change. Display still flashing lock. Used following procedure and every is working now.
    Press pause button and hold down while turning off machine.Continue to hold pause button and turn power back on. If numbers come up on display make note of them for future reference. Release pause button and all lights on display will light up. Turn power off again and then turn back on. If machine was in a cycle it should end it and then return to normal operation. .Dont know if new lock made a difference.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 2 Answers

I have Blomberg WM87120 NBL00 Product code 717518110 and had flashing Lock in display. Bought and installed new lock and no change. Display still flashing lock. Used following procedure and every is working now.
Press pause button and hold down while turning off machine.Continue to hold pause button and turn power back on. If numbers come up on display make note of them for future reference. Release pause button and all lights on display will light up. Turn power off again and then turn back on. If machine was in a cycle it should end it and then return to normal operation. .Dont know if new lock made a difference. Try the reset procedure first.

Posted on Mar 11, 2016

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: What do I do for dL and F error message?

same problem..for a couple months I could get it to work intermittently but finally gave in and the repair guy is here putting in a new control panel. expensive sorry to say.

Posted on Jul 18, 2008

  • 174 Answers

SOURCE: Electrolux EWF1087. door locked shut. when i reset

sounds like door lock is faulty e42 is saying door is still open. could be wiring to door lock also.

Posted on Jul 20, 2010

  • 7 Answers

SOURCE: Door won't lock..machine won't start

could be a faulty door lock as this is required to be locked before a signal is sent to the controller to start the wash cycle, try replacing the door lock, there quite cheal only a few pound

Posted on May 31, 2011

FitzOriginal
  • 842 Answers

SOURCE: Constantly getting an E40 error

Knowing the make and model of your machine would help!!

This sounds like a Zanussi/Electrolux error code. If it is then E40 means "Door open, door interlock, wiring or main PCB"

I'll presume that you DON'T have the door open, so lets move on from there. There is a sensor on the catch when you close the door (Its the one that locks the door when you close it so you can't open it in mid cycle). It also checks if the door is closed so it can lock the door. It MAY be that a good slam of the door will fix the issue because the catch is a bit sticky.

Equally as likely is that at some stage recently you have already slammed the door, or the machine has had a very uneven load that has caused it to shake violently, making one of the 2 wires on the sensor fall off. This will also cause an E40 and is a not uncommon fault.

If the slam doesn't get you anywhere, have a go at the following:

POWER OFF - MACHINE UNPLUGGED FROM THE WALL!

I'm making a few guesses here as I don't know the specific machine

Take the lid off the machine (Usually a couple of screws at the back of the machine at the top, undo them then give the lid a sharp thump with the heel of your hand to push it forward or backwards (The way the lid was held on by the screws should give you a good indication of which way the lis comes off, it MAY even have a couple of screws in the side near the top, hidden under a couple of little plastic caps).

Once the lid is off, take a look at the sensor for the door. It is directly mounted around or on the door catch, so use the position of the catch on the outside of the machine to figure where it is - This is going to be a tight squeeze, it will be made easier if you tip the machine back by 45 degrees so the drup suts back in the chassis and gives you more room.

You should clearly see 2 spade tags on the sensor with a wire on a spade connector attached to each one. If one is off - good news - put it back on (You might want to give it a squeeze with a pair of pliers to tighten the conenctor up a bit so it doesn't happen again.

Reassemble - Job (Hopefully) done.

If the wires were in place and the door slam didn't work, it could be the main control board that is faulty. IF the fix above didn't work, you probably need to call out someone who can test and fix it.

I HOPE I Have the correct machine!!!

Posted on Jun 23, 2011

rickead1
  • 1998 Answers

SOURCE: door locked, won't turn on. won't reset

Remove the bottom panel which would give you access to the pump area if you look up along the side that the door lock is on you will see a cord with a loop on it pull this cord and the door would open. The panel must be removed in order to locate this pull cord. If you have any further questions message me back and please also remember when our chat has fully concluded to rank how this opinion has helped in your appliance situation it allows me to continue helping others in similar situations in the future Thanks Rick
p.s if after you open the door and you were to leave the unit unplugged for 7 minutes if the error did not go away or if the door once again locked up you would have no choice but to replace the door lock assembly on the unit Thanks again Rick

Posted on Jul 04, 2011

Testimonial: "Good advice fast! Thank you so much for your time and expertise!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whirlpool WFC7500VW1 won't start


My Whirlpool washer model WFC7500VW1 will not start--the green Start button keeps blinking and the red Door Locked button keeps blinking. I do not get any error codes.

Feb 23, 2013 | Whirlpool duet Washing Machines

1 Answer

Samsung wfJ1254 washer Won't start and makes


You will need to replace the door lock.

Nov 21, 2012 | Washing Machines

1 Answer

My Kenmore front load washer will not fill--it sounds like it is draining instead. The last load washed did not spin correctly and the clothes were very wet when cycle completed.


Washer Not Filling:


  • Door Not Closed and Locked
    • Front load washers won't fill if the door is not closed and locked. Listen for the door locking when starting a cycle, then pull on the door to make sure the door is closed and locked.
  • Delayed Start Feature
    • Some washers have a delay prior to filling, where the electronic control is checking the dispenser function. This is Normal.
  • Flashing Lights or Error Code on Display
    • When there is a filling issue, the washer may shut off and display one of the following codes: LF, LE, nF, IE, FH, E10 or F20.
    • If the washer is displaying one of the above error codes, then do the hard reset procedure listed below.

If the appliance is not accepting input from the control panel, follow the steps below to reset the control:

  1. Unplug or turn the circuit breaker off for 30 seconds.
  2. Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds.
  3. Press the Pause / Cancel / Stop button twice to clear the display.
  4. Start a short cycle, to check operation of the appliance, by selecting a cycle and pressing and holding the start button until the appliance starts.

Oct 15, 2012 | Kenmore Washing Machines

1 Answer

Kenmore Elite Model 110.42926 202 after setting the desired cycle will not start when you push the start button


see this causes and fix it. God bless you
Incoming Power Problem If the washer won't start check to see if there is power at the electrical outlet which the washer is plugged into. Plug a lamp or radio into the outlet to check it. If the outlet is dead, check the circuit breakers or fuses for the home.

Power Cord If the washer won't start, check to be sure there is power to the electrical outlet for the home. If that is OK, the power cord itself might be defective. This is rare. You can check the power cord with an Ohm meter for continuity.
User Control and Display Board If the washer won't start, the user control and display board may be defective. Check for power to the washer first.



Timer If the washer won't start the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.



Line Fuse If the washer won't start the line fuse might have blown.



Thermal Fuse If the washer won't start the thermal fuse may have blown. It can be tested for continuity. Watch our fuse testing video for more information.



Line Fuse and Holder If the washer won't start the line fuse might have blown, or the line fuse holder might be damaged and need to be replaced.

Main Control Board If the washer won't start the main control board might be defective. This is not common. Check other parts and causes first.



Door or Lid Latch Assembly If the washer won't start the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.



Door Lock Motor and Switch Assembly If the washer won't start the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.
10_5_2012_7_06_37_pm.jpg

Oct 05, 2012 | Kenmore Elite 45986 Front Load Washer

1 Answer

My Kenmore H3T washer will not start. When a specified wash cycle is chosen Time of Cycle is displayed but the light for the cycle only flashes and washer will not start. No error code is displayed.MO


see this causes and fix it. God bless you
If the washer won't start, check to be sure there is power to the electrical outlet for the home. If that is OK, the power cord itself might be defective. This is rare. You can check the power cord with an Ohm meter for continuity.
If the washer won't start check to see if there is power at the electrical outlet which the washer is plugged into. Plug a lamp or radio into the outlet to check it. If the outlet is dead, check the circuit breakers or fuses for the home.
If the washer won't start the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.
If the washer won't start the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.
If the washer won't start the main control board might be defective. This is not common. Check other parts and causes first.
If the washer won't start the line fuse might have blown, or the line fuse holder might be damaged and need to be replaced.
If the washer won't start the thermal fuse may have blown. It can be tested for continuity. Watch our fuse testing video for more information.
If the washer won't start the line fuse might have blown.
If the washer won't start the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.
If the washer won't start, the user control and display board may be defective. Check for power to the washer first.
9_27_2012_11_38_48_pm.png

Sep 27, 2012 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

1 Answer

Affinity frigidare front load washer won't start. It beeps with message flashing (DR)


Hello zabbster - Typically the DR or DO error code indicates that the door switch is not closed. Make sure that the door lock is completely closed. If the door is closed, make sure the door latch is not broken. If the latch is broken, you may possibly need to replace the door lock switch.

Sep 25, 2012 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

I own a maytag neptune washing machine. It was working o.k. and suddenly it won't start. I push the start button and it buzzes and shows a message that says,"It appears the door was not opened...


Hi Debi:
First I suggest to try unplugging the unit for 60 seconds to reset the control board. If that doesn't work then open the dispenser and remove the softner and bleach container. There is a cord near the front you can pull to open the door lock. If you still have issues with your door lock after manually opening the door, you will need to order and replace the door latch assembly.

Also I could bet you need to replace your door latch assembly. Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Dec 06, 2011 | Maytag Neptune MAH7500A Front Load Washer

1 Answer

Door won't open on whirlpool duet washer frontload


Press the cancel button twice to cancel the error code. There should be an error code flashing -- for example 'F02'.

Nov 10, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Door locked, won't turn on. won't reset by pressing pause/start/power or unplugging washer.


Remove the bottom panel which would give you access to the pump area if you look up along the side that the door lock is on you will see a cord with a loop on it pull this cord and the door would open. The panel must be removed in order to locate this pull cord. If you have any further questions message me back and please also remember when our chat has fully concluded to rank how this opinion has helped in your appliance situation it allows me to continue helping others in similar situations in the future Thanks Rick
p.s if after you open the door and you were to leave the unit unplugged for 7 minutes if the error did not go away or if the door once again locked up you would have no choice but to replace the door lock assembly on the unit Thanks again Rick

Jul 04, 2011 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?

Open Questions:

Washing Machines Logo

Related Topics:

346 people viewed this question

Ask a Question

Usually answered in minutes!

Top Blomberg Washing Machines Experts

debbie

Level 1 Expert

21 Answers

ray gallant

Level 3 Expert

43127 Answers

paul
paul

Level 3 Expert

822 Answers

Are you a Blomberg Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...