Question about Emerson EWC19T3 19 in. TV/VCR/DVD Combo

Open Question

Will Emerson Model EWC09D5 TV receive digital tv transmission?

I use this model to watch local TV programs in my car. Will I still be able to get a signal after the conversion from analog to digital in Feb 2009?

Posted by on

5 Suggested Answers

SOURCE: TV code for Emerson EWC 1301 TV/VCR Combo

how do use revmote to program tv vhs thank you11

Posted on Jun 21, 2008

freetek
  • 5568 Answers

SOURCE: need a code for an RCA RCR312w universal remote-Emerson TV/VCR

To see RCA's code list you probably need their website but Emerson is one of several names now owned and built by Funai, who also builds Symphonic & Sylvania.
You might want to try those codes with your set.  

Posted on Dec 18, 2008

freetek
  • 5568 Answers

SOURCE: programming cable channels for emerson tv vcr dvd combo

To see RCA's code list you probably need their website but Emerson is one of several names now owned and built by Funai, who also builds Symphonic & Sylvania. 
You might want to try those codes with your set.  

Posted on Dec 18, 2008

freetek
  • 5568 Answers

SOURCE: I just got a dish installed and cannot program the remote control

What you can try:
- Check the DirecTV code set for the following brands:
Funai, Symphonic, Sylvania, Aventura, Durabrand, ESA, Magnavox, INSIGNIA, and Misakai

Your set and the above-named are all built by Funai.

Even if you find one that works, it probably will not give you full functionality as would the original TV remote, which you can probably find at http:\\www.remotes.com

Before you buy any 'universal' remote, please don't expect it to absolutely work with your set; there is no such thing as a 'universal' remote.
If you find one that interests you, take the time to look up the mfr.'s website and check the code lists for your set.

Posted on Sep 04, 2009

gopakumarg43
  • 69718 Answers

SOURCE: What is the TV model

Hello
Here is some four digt universal remote codes for Emerson. One amoung them will wakeup your TV.

[0004 0009 0044 0135 0049 0051 0189 0053 0147 0039 0130 0227 0233 0250 0252 0254 0257 0265 0266 0310 0325 0456 0040 0041 0042 0021 0023 0024 0179 0045 0025 0027 0030 0032 0034 0035 0037 ]

Proceedings

Direct Code Entry

  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
Code Search Method

If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.
  1. Manually turn on the device (TV, VCR, etc.) to be controlled.
  2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
  4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
  5. Press and release MUTE to install the code. The indicator light goes off.
Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.

Universal three digit remote codes for emerson are

004/ 009/ 014/ 023/ 024/ 025/ 026/ 027/ 030/ 032/ 033/ 034/ 035/ 036/ 037/ 038/ 039/ 040/ 041/ 042/ 043/ 045/ 046/ 049/ 053/ 116/ 135/ 147/ 177/ 179

Posted on Nov 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get free local TV over-the-air stations?


The Quasar VV-2002 only has an NTSC (analog tuner). Very few stations with NTSC transmitters are still broadcasting. Only low-power stations were allowed to continue broadcasting an analog signal. Unless you are very close to one of the transmitters, your TV will not tune in the station.

You'll need to connect the TV to a digital-to-analog over the air converter box. (The low-end ones that were free or cheap with the government coupon are harder to find; a few models are still available.) These convert the ATSC (digital) signal to NTSC. Then use an appropriate antenna and follow the instructions to tune in the available OTA signals. Send these to the TV either on the RF or composite Line-in. Set the TV to the appropriate input and use the converter box to change channels.

I hope this helps.

Cindy Wells
(20" TVs weren't required to have an ATSC tuner until 2007. Since there are reviews for the VV-2002 from 2004, it obviously is an older set.)

Nov 19, 2015 | Quasar VV-2002 20 in. TV/VCR Combo

1 Answer

I have a Sylvanis VCR/DVDcombo and a Standard TV.


The converter box receives hte digital signals and converts them into either channel 3 or 4, or into direct video (red,white,yel). The output of the converter box must go into the VCR input for recording to work. Before the conversion, the tuner of hte VCR would receive the RF signal the same as the TV. The tuner inside the VCR is an analog tuner not digital, so it needs the conversion too. Most converters will provide both the A/V signal (R/Wh/Y) and RF (coax connector).

Hope this helps,
Dan

Sep 30, 2009 | Sylvania 6720FDG 20" TV/VCR/DVD

1 Answer

Is the Hitachi TV Model CT1955 digital?


Sorry, but no. That is an analog TV. You will need a digital conversion box for it to pick up digital channels in the US in June

May 29, 2009 | Televison & Video

1 Answer

Do I need a digital converter box for sharp 13VT N100


Yes you will need on because you are receiving a analog signal and will not decode the digital signal without one.Hoe this answers you question.

May 18, 2009 | Sharp 13VT-N100 Combo

1 Answer

Local channel went digital, lost signal.


You need a digital to analog convertor box to recieve the digital signal.

All UHF+VHF signals will be digital starting in June.

Thanks for using FixYa - a FixYa rating is appreciated.

Feb 20, 2009 | Televison & Video

1 Answer

Antenna/Cable Switch


You can get a 75 Ohm to 300 Ohm balun from a local Radio Shack Store and connect it to VHF antenna but you won't be able to receive off the air signals for very long because in about a month all TV signals will be being broadcast in Digital Format nationwide and all you will receive is SNOW. You'll need to also buy a Digital to Analog conversion unit as well to receive off the air programming. Sorry for the bad news but that's the advancement of technology and mandates from our government (FCC).

Hope this helps and Happy New Year,

Backyard_Jim

Dec 31, 2008 | Symphonic WF-719 19 in. TV/VCR/DVD Combo

1 Answer

Digital Ready TV ?


This set in can not receive digital signals directyl. If you are connected to cable or satelite, you are ok. Only if you are using an antenna for signals will you be effected by the changeover in Feb 2009.

Dan

May 12, 2008 | Panasonic PV-M2559 25 in. Combo

1 Answer

TV without cable


Depending on how far you are from the broadcaster you can try Rabbit ears or and outside antenna.. If the set is more than two years old you may need a digital converter after Feb 17th

Mar 12, 2008 | RCA 27F500TDV 27 in. TV/VCR/DVD Combo

1 Answer

Philips CCB130AT02 TV/VCR combo


Is this an Analog TV? Does it have a picture tube and not an LCD or plasma screen? Most likely this is a Analog TV.

If it is an Analog TV (and I would bet that it is), then no, it does not have a digital (QAM) tuner to pick up DTV broadcasts. The fact that it has a VCR also indicates that its an Analog TV.

If you are picking up your TV signals from an outside antenna and not cable, then yes, you will need a converter box to convert the new digital signals to Analog so that you can continue to use your TV set.

If you are using cable to receive your channels, the cable company already provides the conversion for you and your TV will continue to work as before.

The government is giving out coupons to help consumers defray the costs of purchaing a converter box. The following sites are good places to obtain more information.

www.ntia.doc.gov/dtvcoupon

www.DTVanswers.com


Good luck!
- Jim


Feb 06, 2008 | Televison & Video

Not finding what you are looking for?
Emerson EWC19T3 19 in. TV/VCR/DVD Combo Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Emerson Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69718 Answers

matt martin
matt martin

Level 3 Expert

1198 Answers

 Grubhead
Grubhead

Level 3 Expert

4678 Answers

Are you an Emerson Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...