Question about Pride Mobility Products Jazzy Select

1 Answer

Pride Mobility jazzy select battery cable

I've lost the electrical cable to the black adapter? and to the plugin. I've got the charging plug to the chair and back to the black box. Where can I find a replacement (low cost if I can)? Low fixed income. Does anyone know where I can find the missing half?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 104 Answers

Yes a thrift store its the same as a computer plug 2 or 3 bucks

Posted on Dec 18, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 29 Answers

SOURCE: jazzy jet 3

Look in your owners manual for the flash code anwser. Make sure when you hit the power button you only touch it for 1 sec not more. If you press the power button for more the 2-3 seconds you place the power chair in LOCK OUT mode. lights will flash and not power. also check your free wheel levers. one on each moter. Mike

Posted on Sep 07, 2009

  • 4 Answers

SOURCE: Pride Jazzy Select batteries not charging

If you use an automotive charger you have to charge each battery individually as they should be 12vdc hooked in series.

Clean contacts and assure yourself that each lead is charging properly. Jazzy has many different models so it impossible to know which you have. But there should be some info on the charger to tell you if your output is 24v or 2-12volt DC leads.

Jazzy has a web site and there is a member section where you can ask questions.

Posted on May 17, 2009

  • 175 Answers

SOURCE: have jazzy select series need to know flashing Code #9

Consult your owners manual for the flash code guide. I believe that you probably have a PG Drives Joysitck/Controller, in which case a 9 code would indicate problem with the brake system. Check the free-wheel levers by placing them in the neutral position, and then firmly placing them back in drive. Try to restart. If still flashing, you need to remove the seat and the shroud and examine the connections inside the base of the chair. The brakes are at the end of the motor, and there are thin wires coming from them back to the controller box. Inspect these wires for any damage, and follow them back to make sure any connections on the way are tight, and that the connections for all clip connections are tight.

The brake is electrically operated by a solenoid. If the solenoid has gone bad, then this will also cause a fault code. Contact your dealer for servicing this part. Good Luck.

Posted on Jul 09, 2009

  • 945 Answers

SOURCE: jazzy select 14 won't charged - have replaced

At a minimum your batteries need to be charged for 12 hrs a day for the first month if not they will not build the capacity and will dwindle and die for example it is at only 25% capacity it says it fully charged but will die quickly this happens because it is charged to its full capacity but that is only 25% of the batteries true potential resulting in short battery life. Also the new batteries need to be charged before they are put on your jazzy. Then its a matter of if not in use put on charge. I think you need to have a word with your dealer.

Posted on Oct 19, 2009

  • 692 Answers

SOURCE: my jazzy select 14 keeps lighting up like its

Can you tell if the lights are flashing a number of times then pausing slightly then flashing the same number again and so on? If not then check to make sure your not in "freewheel". The levers are behind each wheel If you are getting a flash code determine the number of flashes the codes should be in your user manual or goto Pridemobility.com and you can download a owners manual for that chair. Hope this helps

Posted on Aug 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Jet3 wheelchair not charging with internal (accoring to amp meter)


you will need a off-board charger to charge the chair Strege Mobility

I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

Sep 13, 2017 | Jet 3 Ultra Power Chair

1 Answer

My sons pyramat chair stopped working when he plugged in the wrong adaptor, it seems the electrical charge is now not getting through, if it is really pushed in the lights flicker on & off. How can I...


First you need to know the how much power the chair needs yes voltage and amperage if the adapter did not match and it was over then you blew it but if it was under it might have a chance. one place would be any place that fixes electronics.

Aug 08, 2012 | Pyramat Sound Rocker Gaming Chair

1 Answer

Acer Aspire 5536 only gives black screen when i connect power supply


  • Nothing is more annoying than a monitor that refuses to turn on. Make sure your Acer monitor is plugged in to a functioning outlet. If it's plugged into a power strip, try replacing it with a new one or moving the plug to a different outlet. Ensure that both ends of the power cable are plugged in firmly and securely, and that the connection to the monitor is not loose.
Cable Issues
  • Your Acer LCD monitor will usually accept DVI and VGA inputs. If you have an older computer, a VGA cable should work fine. If it doesn't have a VGA port, you'll need to obtain an inexpensive DVI to VGA adapter at your local computer store. A DVI cable, however, is compatible with most modern computers and offers superior picture quality over VGA. Make sure you're using the cable that's compatible with your system, and that you have the proper conversion adapter, if necessary.

Jun 19, 2012 | Computers & Internet

2 Answers

I purchased a Pronto 41 wheelchair and a Winsunny battery charger. The charger didn't have a manual so I'm wondering what the best procedure is for recharging the batteries. Do I need to turn the...


Joe See my tips on charging batteries No you don't have to leave the chair on when charging. Charge overnite after using it during the day. Always have the charger off when plugging it into the chair and unplugging from the chair. The charger you have doesn't have an on/off switch so get a power strip with the on/off switch, plug that into the wall and plug your charger into the strip use the switch on the strip to turn the charger on and off this will save you having to plug and unplug the charger rom the wall. Always store or put the chair up fully charged. If you don't use the cair daily charge at least once a week. It takes 9-10 chargings to get the batteries operating at 100% so use the chair and charge overnight while you sleep Never leave the charger on the chair more than 12 hours Hope this helps you

May 30, 2011 | Electric Mobility Pronto M41 Power Chair...

1 Answer

When I plug in my Jet 3 Ultra 4500, it seems to charge - the charging lights come on - but it never charges. In fact, I can't get it to move at all, even when plugged in. I think I am using the...


when you plug in the charger do you get any amp reading on the meter located at the rear of the chair near where the charger cord plugs into the chair. When you plug in the cord the meter should deflect and read 6 amps or so. If you aren't getting any deflection of the amp meter then either the batteries are dead or the charger is bad. If you have a voltmeter you can set it to 200 volts dc and plug the leads into the charger port located under the front of the joystick Plug the leads into the 2 outter holes of the port with the charger plugged into the wall you should be reading 27-30 volts. Unplug the charger and you will be reading the battery voltage and fully charged they should read 25-27+ volts. If you aren't reading 25-27 volts without the charger plugged in you will need new batteries( anything less than 10 volts will not let the chair turn on) if you aren't getting 27-30 volts with the charger plugged in then the charger is bad and you can get or borrow an off-board charger and charge the chair thru the joystick port Hope this helps

May 07, 2011 | Jet 3 Ultra Power Chair

1 Answer

I BOUGHT A USED JAZZY JET 3 ULTRA WITHOUT BATTERIES AND I HAVE BOUGHT 2 NEW BATTERIES BUT AM NOT SURE HOW THE WIRES HOOK TO THEM, IF THE 2 BATTERIES HOOK TOGETHER.


Locate the two wires from the circuit breaker attach one wire (black if marked) to the negative post of the rear battery and attach the other wire (red if marked) to the positive post of the front battery. Locate the two wires coming from the power module plug with a red and black wire. Attach the red wire to the rear battery positive post and the black wire to the front battery negative post. attach the joystick to the nine pin plug at the rear of the chair and turn it on. You should have power at the joystick and the chair should work. Disconnect the joystick put the shroud cover back on grease the seat post and reattach the seat then plug in the joystick and charger plug at the rear of the chair. Charge the batteries before use and charge them overnite for the next 20 days. If you use the chair daily charge your batteries everynite while you sleep unplug in the morning. If you don't use the chair daily charge at least once per week or after you use the chair. Always put the chair up fully charged if you are going to be out of the chair for an extended time the disconnect the batteries at the large plug going to the power module Hope this helps you

Apr 13, 2011 | Jet 3 Ultra Power Chair

1 Answer

How do i connect the 35 amp batteries to my ultra 3


with the battery cables vic seriously I'm gonna assume you have removed the seat and shroud cover over the batteries. Unplug the battery cables from the wiring harness and remove each battery remove the wiring harness from the battery and attach to the new batteries like they were to the old red on positive and black on negative and reinstall in the chair plug the joystick cable back into the chair turn on the chair to make sure you got it right unplug the joystick cable replace shroud and seat plug the joystick cable back in and you should be good to go. charge the batteries before use and then charge them nightly when you go to sleep and unplug in the morning if you use the chair daily charge everynight If you have to stop using it for a while always put it up fully charged and charge weekly Hope this helps you

Apr 09, 2011 | Jet 3 Ultra Power Chair

1 Answer

I lost the manual to my craig cvd505. I am trying to set my 505 as a dvd player to watch on a old tv. It does not have video plugins. It has the older cable plugins in the back. I know I need at...


you need what's called an RF (radio frequency) modulator. it allows the standard video/audio RCA connections (yellow/red/white) to be plugged in then it routes the signals to a standard cable connection (coaxial). This cable connection carries both video and audio signal to channel 3 or 4 (selected on the modulator)._1408.jpg

Apr 06, 2011 | Audio Players & Recorders

1 Answer

Some one give me this DVD burner Sony DRU-540A ..would it use IDE or Sata...It did not come with any cable...what cable i need to get?


If you look on the back of the burner, you will notice either a slot with 39 pins or a small black like plugin. The 39 pins would be for an IDE plug, and the little black pin would be for a sata cable. Simply go to the nearest Radio Shack, Best Buy, or computer hardware store and get the appropriate internal cable. Just advise the store attendant in that area to advise you were such cable is.

These are very simply to plug in, simply plug in to the back of the cd-rom, and plug into the motherboard with a similar plugin on the motherboard. Make sure the plugin on the motherboard states it is Sata, on the motherboard it will have something printed near it with Sata1 Sata2 or something similar. Put the CD-ROM in the closest bay, and plug in appropriately.

Dec 04, 2010 | Sony DRU-540A DVD±RW Burner

Not finding what you are looking for?
Pride Mobility Products Jazzy Select Logo

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pride Mobility Products Health & Beauty Experts

wcdoc1953
wcdoc1953

Level 2 Expert

280 Answers

Colin Taylor

Level 2 Expert

347 Answers

Robin Hill
Robin Hill

Level 3 Expert

1271 Answers

Are you a Pride Mobility Products Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...