Question about Dryers

1 Answer

Hi, we have a Siemens IQ300 Condenser Tumble Dryer which we have recently inherited. Unfortunately it worked for a wek before just stopping. The lights are on and everything looks normal but when you

The lights are on and everything looks normal but when you press the start button after selecting any of the programs it just beeps back at me and nothing happens.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Check to see if it is properly grounded and that the incoming voltage is correct (120V or 240V) for the wiring config you have.on the dryer as it sits. Also try unplugging and wait a minute or so before plugging back in. This will sometimes reset dryer electrical components to factory settings.

Posted on Dec 07, 2012

  • Sarah Brown Dec 09, 2012

    Thank you Jeff. This is where I will strat looking. Regards.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
dididsaythat
  • 291 Answers

SOURCE: Hoover tumble dryer

I think you may have a bad relay on the motor, where power is re-applied after the push start is released

Posted on Oct 14, 2007

  • 1462 Answers

SOURCE: tumble dryer

take the top off. there should be a small relay board to the right just behind the fascia. the fault probably lies in that board - relay not holding in

Posted on Apr 04, 2007

  • 209 Answers

SOURCE: Tumble Dryer won't start

assuming what you say you checked is correct and working then the next place to look is the start relay, located behind the front timer control panel, this sis more often than not a cubed shape box made of clear plastic with about 6 spade connectors on it, look for burn marks inside it, replace if looks damaged, do not attempt to bypass or short out to test, as you will blow the timer or and control circuit board and cause extensive damage

Posted on Sep 26, 2007

JR JR
  • 116 Answers

SOURCE: Kenmore Elite HE3 Dryer (3 yrs. old)

when u push the buttons do all lights light up if so ,, machine is in lock mode ,, press and hold the little icon that read lock for about 3 seconds unitll lights are off then run ,, let see

Posted on Nov 30, 2008

  • 9 Answers

SOURCE: Dryer won't start when start button is pressed and held

check door "close"contact button/switch usually the culprit..

Posted on Aug 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dishwasher bottom part works top part all lights are on and wont work


I'm assuming its a fisher and paykel, you will certainly need more info. Do you have an led display or 3 buttons and lights. Any fault codes, flashing beeping when buttons are pressed etc. If everything is normal no unusual beeps lights etc but nothing AT ALL happens when you press start it is the door 'switch' which is actually a light that is reflected through a plastic prism and back to itself ( originates from the board) check the prism top right drawer frame. Just compare to working drawer. If not more info required.

Jul 07, 2013 | KitchenAid Dishwashers

1 Answer

How do I prevent the beeper from beeping when the dryer cycle is finished? I did not press the beeper button but I can't seem to program it so it does not beep. Please help. Thank you. My dryer is a T...


In your manual it says if the indicator light is on then the buzzer is on so to turn off the buzzer at the end of your program you would press the button again. Heres is that section from your manual

5. Select the buzzer (if desired)

^ Press the "Buzzer" button to have a

tone beep at the end of the program.

Indicator light:

on = buzzer selected

off = buzzer not selected

To adjust the buzzer volume:

- turn the dryer on

- close the door

- select a program

- if the indicator is lit, press the

"Buzzer" button so the indicator light

goes out.

^ Press and hold the "Buzzer" button

until its indicator is lit and you hear
the desired volume and tone.
also if you need the manual for your machine your can get it directly from this link click here
http://www.retrevo.com/d/ds/progress?doc=508a0566a4fcfb2910e707b71d1fb918&u=1&rk=0.2030122370322724

if you have any further questions message me back and please also remember when our chat has fully concluded to rank how this opinion has helped in your appliance situation Thanks again I await if you have any further reply
Rick

Jun 26, 2011 | Miele T8003 Dryer

1 Answer

P_powers on but cant get to main screen. wont power off


turn on ps3 leave on stand by (red light), hold eject button and power button until you hear beeps and a message appears. connect controller and press ps button. system restore screen should appear, select restart system and from there it should restore everything back to normal. don't forget to rate

Jan 13, 2011 | Sony Playstation 3 (PS3) Console

2 Answers

My ps3 has stopped working! It says: "Cannot start. Correct hard disk not found." Please, please, please can you help??? Many thanks, Mark & Michelle


Ouch, Bad news Mark and Michelle. This is a fatal error on the hard drive. Basically, the hard drive needs to be replaced :( Sorry

Aug 12, 2010 | Sony Playstation 3 (PS3) Console

1 Answer

Not able to gat to the menu


turn on ps3 leave on stand by (red light), hold eject button and power button until you hear beeps and a message appears. connect controller and press ps button. system restore screen should appear, select restart system and from there it should restore everything back to normal

Aug 26, 2009 | Sony Playstation 3 (PS3) Console

2 Answers

Maytag Neptune TL electronics problem


neptunes are known for the control board, spin bearing and wax motor going bad. replace unit

Jun 20, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

The program light goes off and the BF162 doesn't start...


When you keep the button pressed for a few seconds the lights go off, this resets the dishwasher. Then press the p button again to the program you want 1st light is heavy soil 2nd light is normal soil, 3rd light is eco wash, 4th light is rinse. At the end of the cycle the program light you have selected will flash.

Apr 24, 2009 | Hotpoint 23 in. BFI62 Built-in Dishwasher

2 Answers

B2300 breadmaker


I had the same problem and what you need to do is hold the start button down for 3 seconds and that will clear the default setting (1 3:30). Then select the settings you need starting with the program setting for your recipe (i.e. #4 for sandwich bread). Bear in mind that you may not be able to select your crust light/dark option for some recipes, but will be able to select the loaf size. I assume this is because the recipe program (i.e. #4 for sandwich loaf) is already prescribed in the setting. When you have all of your selections then press your start button, but don't hold it down for longer than a second because it will clear everything and you will have to start again from step 1. Good luck!

Dec 17, 2008 | Black & Decker B2300 Bread Machine

2 Answers

WASHER WON'T START


possible door latch or even the strike on door itself may be broke

Sep 04, 2008 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Blue light


Press the mute/program button, then press the caller ID-volume button to select handset setup (then press mute/program again to select this option). Next press tye caller ID-volume until you get to Default settings (its the last setting so pressing the up arrow is the fastest way to it). Press the mute/program button again to select the option. Use the caller ID-volume button to select 1yes. This will return the phone to the factory settings and for took care of the blinking blue light, however you will loose any custom setting or numbers you entered.

The first time I did this it didn't work, so I did again and toward the end of the steps above the phone beeped at me and stated "Reset Default Settings" (or something like that) then time I hit the mute/program button again and everything worked great. I think that last beep maybe have been a are you sure you want to restore to default question.

Remember tis will erase any custome settings you made on the phone (ring tones, ring volume, memory, etc.)

Jan 31, 2008 | GE 28111 Cordless Phone

Not finding what you are looking for?
Dryers Logo

Related Topics:

553 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Brad Brown

Level 3 Expert

15644 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...