Question about Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Maytag atlantis mav6300aww

Drum is nou spinning, its on but when i open the lid its not spinnig. I checked the belt and its intact and moves ok. Is my problem the transmission pulley & bearing kit?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Maytag Master
  • 9,472 Answers

Replace the lid switch. Here is the part to order.

Posted on Dec 08, 2012

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1294 Answers

SOURCE: Maytag washer will not spin

If your washer does everything but does not spin, it is your outlet filter which is blocked. Locate this and clean out, it has to work fine. Refer user's manual.

Posted on Jun 05, 2007

SOURCE: Maytag Washer PAV2300AWW

Your Thrust bearing on the bottom of the transmission is not releaseing the break. try turning the pulley with the belt off in the opposite direction this should free up your break. If it doesn't replace your brake ststor and rotor as well as your thrust bearing. This should solve your problem. Roger

Posted on Sep 27, 2007

SOURCE: Maytag Performa PAV2300AWW screaching noise, belt problem, pulley broke

My Maytag Performa was making the loud squealing noise. I changed out the water pump/bearing, took care of the problem.
Putting a new belt on just help burn up the bearing (they needed replacing) and probably ruined the new belt. Probably seized the water pump bearing and the belt jumped and broke the motor pully. A washing machine motor is very strong, when that h20 pump bearing seized (or possibly some bearings jamed up) the motor kept on turning that belt and the plastic pully gave in. You'll need to replace that also. If the h20 pumb bearing is turning freely, likely the bearings jammed up but or now loose. That bearing should be tight, no slack or play in it. You can probably wobble the pully on it all around while turning it. The slightest slack is too much.

Posted on Oct 29, 2008

  • 1 Answer

SOURCE: Maytag Performa Washer spins out of balance

There was a recall on the washer base, which caused the unbalanced problem. Find Technical Buletin TDL-0050B-B issued by Matag.

Posted on Oct 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer makes grinding/loud sound and will not agitate-spins fine


Look under the washer. Is there a little pile of black rubber shavings? This sounds like the basket coupler between the motor and the drum. If the coupler is the problem it is inexpensive to fix. Some also call this part the "clutch". It kind of looks like a hockey puck with six holes in it... three for the motor, three for the clothes drum. In your case, I suspect that the holes are intact in the direction of spin, but as soon as it reverses for agitation, it breaks out through the back of the holes.

Jul 09, 2017 | Maytag Atlantis MAV6260AWW Top Load Washer

1 Answer

Motor smell hot drum will not spin or pump out water Maytag atlantis


Im not an expert, but.Ok, but it wash? The only problem is at spin? if not wash at all:
Disconnect from the outlet, remove the belt, and by hand turn the pump and drum. Its suppose to move with low resistance in both directions, will not spin freely, but turn easy by hand. Do the same with motor. IF the drum and pump moves in both directions, I suspect about the motor.
If the only problem is at spin:
Do the same, but place special attention at the drum when you turn in reverse. Look if you see the brake Disk turn.

Nov 27, 2011 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

My maytag atlantis washer purchased in 2002 would not spin on the colors spin cycle. I turned the control completely around to the spin cycle and tried again and it didn't work. I also set it on the spin...


Jim, I would be looking at the lid switch assembly. Try to press down on the lid in the very front edge. IF the switch is going out of tolerance, the added pressure will activate the switch and allow the machine to spin. If it were a transmission problem, you would hear the motor. (I'm assuming you are not hearing the motor).
If you are hearing the motor run, check the motor slides to make sure they are not rusted and the motor is able to pivot back and forth freely.
Let me know if you have any other questions on this!!

Aug 19, 2010 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Maytag atlantis washer mav6300aww drains water but does not spin


my maytag washer model #MAV6300AWW will not spin out during cycle but can turn it back to spin and will spin out

May 30, 2010 | Maytag Atlantis MAV6000 Top Load Washer

2 Answers

Maytag Atlantis screeches @ end of spin cycle,


may be something stuck in the drum or a segment raised on the motor. to test either remove the belt and spin the drum if no noise then the motor is faulty. if a noise then there may be a bra wire between the drum/tub.

Mar 16, 2009 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Spinnig slow sqecking noise


This is joyce
sounds like the belt needs to be tighter. sounds like its slipping on pully. that may be why its not spinning correctly.
thanks
joyce

Feb 06, 2009 | Maytag Atlantis MAV6451 Top Load Washer

1 Answer

Maytag MAV6000 Top Load Washing Machine


Tip the machine back remove the belt try to turn the drive pulley manually . sorry the larger pulley in the centre. if you can turn it counter clockwise and feel the inner drum moving then the thrust bearing is ok. if not you may need to replace it.Also a bad lid switch can cause this problem.

Nov 07, 2008 | Maytag Atlantis MAV6000 Top Load Washer

2 Answers

Mav6260 washer will not spin


the belts on these units will streach, and alot of the early unit had bad belts.

the unit should spin with or with out water in the spin cycle

also the thrust bearing on these units go bad often.

this is a magic chef washer with the maytag name on it.

Apr 26, 2008 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Maytag Atlantis 7600 spin cycle (top load)


the maytag runs in one direction for wash. it reverses to drain and spin - check for a broken or loose belt. maytags I have run into circa 1989 have two belts. as for the softener dispense, there may be a solenoid valve that is supposed to open. may be just a flapper type of valve. softener goes in by gravity feed.

Sep 04, 2007 | Maytag MAV7600 Top Load Washer

Not finding what you are looking for?
Maytag Atlantis MAV6000 Top Load Washer Logo

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

588 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

John Tripp
John Tripp

Level 3 Expert

4655 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...