Question about Pioneer PRO-710HD 64" Rear Projection Television

1 Answer

My pioneer Pro-710 hd 64in keeps shutting down when turn on.

S/N SLPT000987UC

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Pioneer Master
  • 14,553 Answers

The most common problem this group of sets had was bad solder connections all over the power board that develop after some years of use----most of them I have repaired a total resolder of most or all connections on that board fixes the problem.

Posted on Dec 07, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
MrBob84
  • 90 Answers

SOURCE: Pioneer Elite Pro 710 HD

If your Elite 510/610/710 - and the earlier 520/620/720s - works fine when you turn it on but starts to go hinky on its reliability once it has warmed up, you still have a shot at getting that sit remedied for a very nominal fee - or nothing, if you know what you're doing and are an electronics professional. Those models were improperly soldered at the factory on their PS boards. Those PS boards took years to go bad, but now that the constant barrage of expansion and contraction of the too-thin solder joints has started its inexorable journey towards taking down your set, the clock is ticking. You don't have much time.

One thing is very important, and I can't stress it enough: STOP USING YOUR SET NOW. Things could get much worse if you do. That means NOW, even if you are watching it right now. A deadly spike caused by the bad solder joints currently on that power supply board could be getting ready to be produced by a connection that is getting ready to separate as we speak, and that spike could take out one or more of the boards downline. One guy who called me had kept using his set for months with these intermittents happening, and eventually both the converence and the deflection boards went out, both in an instant. The set would not turn on again, and built-in indicators on the circuitry showed 3 boards now needed attention. With 3 boards to now have to deal with, he decided not to get his set repaired at all, due to the now tripled expense. His set was now totalled. It tears my heart out when one of these fine machines goes down for the count because of misuse - continued use when it's obviously hurt - and is then DNR'd by its owner. That all could have been avoided by taking action promptly rather than continuing to tempt fate, on his part.

Send me an email requesting it, and I'll send you back an emailout on how to remove it, what it costs, how to wrap it and send it, where to send it, etc. I can't divulge certain aspects of all this on the net here, must keep some of it close to the vest. Will be glad to tell you personally, by email or on the phone.

I will tell you this much - I charge $275 for the resoldering op, you pay the shipping both ways. That's less than it costs to get a replacement board from Pio and have a local Pio warranty station install it.

Keeping the same board in your set rather than replacing it is the way to go, IMHO. That way the voltages it was set up with originally, stay the same. If you get a replacement board, those voltages can be very different, affecting the precision of settings downline. Voltage regulation only has to fall within certain parameters, so different PS boards will produce different sets of voltages. The PS board and your set are now a matched pair. The best way to retain your precision in downline sets of settings, is to keep your original board in the set, the one your set was originally set up at the factory with.

To find the PS board, follow the power cord from the wall. It will lead you right to it. Use the big bubble-wrap to send it rather than the small stuff, and box it in an oversized box for the journey.

Mr Bob
www.imageperfection.com
bob@imageperfection.com

Posted on Sep 01, 2009

  • 74 Answers

SOURCE: I have a Pioneer pro 710 hd rear projector tv. 9

you must have checked by a repairman it could be the video output i.c. or it could be the picture tube as they all work with separate circuit boards

Posted on Dec 18, 2009

  • 1619 Answers

SOURCE: Panasonic Pro 710 HD Shuts off for no reason

Most likely bulb is dying and cooling fans are clogged with dust. The bulb iis more like a street light than a home bulb.

Posted on May 15, 2010

  • 8457 Answers

SOURCE: Hi My name is Dieter and I have a Pioneer Elite

The tv "LAMP" LED light indication front of the screen panel flashes?When was the last time u replaced the tv projection lamp on this tv?If the last time u replaced the projection lamp was like 1/12 or 2 years ago?The tv been on and used like 4 or 5 hours a day?The tv projection lamp life are over.Require a new projection lamp.

Posted on Sep 19, 2010

  • 11800 Answers

SOURCE: I get bright flashes on

Bright flashes in a CRT tv means that you get high tension discharges in the video final board which in turn trigger a power surge that cause the tv to shut down.
You didn't said which colour is the flash so i 'm supposing that is white. This mean that the discharge is affecting all 3 tubes at the same time, which means that you must verify the high tension leads, the flyback transformer and all the groundings on the tubes. Also verify the static dischargers on the video board.

Posted on Nov 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I use a universal remote to adjust my settings for the elite Pro 710 HD?


I doubt it, we have in our shop about five of their remotes and each only works on one or two models--bite the bullet to get another or if you have the original but it does not work, most shops can fix that for a reasonable price.

Dec 14, 2012 | Pioneer PRO-710HD 64" Rear Projection...

1 Answer

Panasonic Pro 710 HD Shuts off for no reason


Most likely bulb is dying and cooling fans are clogged with dust. The bulb iis more like a street light than a home bulb.

May 15, 2010 | Pioneer PRO-710HD 64" Rear Projection...

1 Answer

The convergence chip is going in my pioneee elite


Yes there are two ICs in your model they are around 20.00 each for quality ICs. Cheaper ICs are available but I wouldnt recommend them as theyre most likely the inferior chineese made ICs and they fail quickly.

Nov 27, 2009 | Pioneer PRO-710HD 64" Rear Projection...

1 Answer

Pioneer Elite Pro 620 HD TV on several occasions the screen has gone black but sound continues and the power green libht remains on. After shutting down for 10-15 minutes picture comes back.


Pioneer Elite Pro rear projection 620HD - Picture is still there but brightness and "white" have faded over years allowing for mediocre viewing when room is dark only. During the daylight picture is visible if viewed straight on and within 15 feet from set. Any suggestions?

Oct 16, 2009 | Televison & Video

2 Answers

It keeps shutting off intermittently. I am


I work on pioneer, and I would not assume that. The tv is going into a shutdown condition. The tv has detected a fault and will shut off, being 9 years old some of these tv's are two part with console unit that the panel plugged into. If it is one of these it could be the console. The diagnostic on these are very complex, with a series of 4 different leds that need tracked. This needs to be diagnosed by a Pioneer pro. They are more complex than the newer models because the technology was very new when your set was made and the consolidation of many of the circuits had not been done yet. Therefore many more circuits that could fail leading to a more complex diagnosis.

Oct 10, 2009 | Pioneer PureVision Pro-1000HD 50 in....

1 Answer

Pioneer 710 hd power/not turning on 10/12/08


When the set goes into protection BANG like that, without any intermittencies, usually the convergence ICs have gone out and need replacing. I recommend using the STK 392-180s, which are the stronger upgrade to the 392-110s used originally. You'll need 2.


Mr Bob
www.imageperfection.com
510-278-4247
bob at imageperfection dot com

Oct 13, 2008 | Pioneer PRO-710HD 64" Rear Projection...

3 Answers

HD CONVERTER FOR COMPONENT


Just Google hdmi to component....You'll find plenty of choices.

Jan 10, 2008 | Pioneer PRO-710HD 64" Rear Projection...

1 Answer

PRO-510HDTV



The intermittencies you mention are common on this
series. The PS - power supply - board needs a
virtually complete resolder op, as the solder used in
that run of units was weak and thin. It will not get
better on its own, any more than needed dental work
will.

Send it to me and I will resolder it and send it back.
I have done so on a number of PS boards in this series,
and am running at 100% success on saving the
510/610/710 series of Pioneer Elites when all they need
is the resoldering op. There is a procedure to follow,
so contact me directly.

www.imageperfection.com
510-278-4247

Mr Bob

Nov 08, 2007 | Pioneer PRO-510HD 53" Rear Projection...

7 Answers

Pioneer Elite Pro 710 HD


If your Elite 510/610/710 - and the earlier 520/620/720s - works fine when you turn it on but starts to go hinky on its reliability once it has warmed up, you still have a shot at getting that sit remedied for a very nominal fee - or nothing, if you know what you're doing and are an electronics professional. Those models were improperly soldered at the factory on their PS boards. Those PS boards took years to go bad, but now that the constant barrage of expansion and contraction of the too-thin solder joints has started its inexorable journey towards taking down your set, the clock is ticking. You don't have much time.

One thing is very important, and I can't stress it enough: STOP USING YOUR SET NOW. Things could get much worse if you do. That means NOW, even if you are watching it right now. A deadly spike caused by the bad solder joints currently on that power supply board could be getting ready to be produced by a connection that is getting ready to separate as we speak, and that spike could take out one or more of the boards downline. One guy who called me had kept using his set for months with these intermittents happening, and eventually both the converence and the deflection boards went out, both in an instant. The set would not turn on again, and built-in indicators on the circuitry showed 3 boards now needed attention. With 3 boards to now have to deal with, he decided not to get his set repaired at all, due to the now tripled expense. His set was now totalled. It tears my heart out when one of these fine machines goes down for the count because of misuse - continued use when it's obviously hurt - and is then DNR'd by its owner. That all could have been avoided by taking action promptly rather than continuing to tempt fate, on his part.

Send me an email requesting it, and I'll send you back an emailout on how to remove it, what it costs, how to wrap it and send it, where to send it, etc. I can't divulge certain aspects of all this on the net here, must keep some of it close to the vest. Will be glad to tell you personally, by email or on the phone.

I will tell you this much - I charge $275 for the resoldering op, you pay the shipping both ways. That's less than it costs to get a replacement board from Pio and have a local Pio warranty station install it.

Keeping the same board in your set rather than replacing it is the way to go, IMHO. That way the voltages it was set up with originally, stay the same. If you get a replacement board, those voltages can be very different, affecting the precision of settings downline. Voltage regulation only has to fall within certain parameters, so different PS boards will produce different sets of voltages. The PS board and your set are now a matched pair. The best way to retain your precision in downline sets of settings, is to keep your original board in the set, the one your set was originally set up at the factory with.

To find the PS board, follow the power cord from the wall. It will lead you right to it. Use the big bubble-wrap to send it rather than the small stuff, and box it in an oversized box for the journey.

Mr Bob
www.imageperfection.com
bob@imageperfection.com

Aug 01, 2007 | Pioneer PRO-710HD 64" Rear Projection...

Not finding what you are looking for?
Pioneer PRO-710HD 64" Rear Projection Television Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74185 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Are you a Pioneer Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...