Question about Maytag PAV2300 Top Load Washer

Open Question

Disassemble washer cabinet for PAV2300AWW

I need to know the secret for getting the cabinet open to fix a leak. This is a Series 14 washer; I found the clips on the bottom and the screws on the back below the control panel, but I need to get to the water inlet assembly.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Krazytech
  • 725 Answers

SOURCE: Drain hose leak

Hi Krazytech here, You will have to remove the cabinet to get to the pump end of the drain hose. First you must remove the top insert a putty knife to open the top lift up then remove screws that hold on the top then remove the screws that hold on the bottom. then you can get to the pump I alway replace the factory spring clamps with a screw hose clamp they are much better.. let me know

Posted on Aug 24, 2007

gwshaw71
  • 83 Answers

SOURCE: To replace part #1477, female hinge part for lid

Take a plastic putty knife and insert it under head. On each side.there is a push tab now where the 2 screws used to be push real hard in and the head will pop up

Posted on Dec 02, 2007

  • 219 Answers

SOURCE: "nF" error code at end of cycle, and water leak

nf means u have a bad water valve u may also have a bad hose underneath the lid as well if u have water in your control

Posted on Mar 18, 2009

  • 5 Answers

SOURCE: Water leak from bottom of Maytag Neptune washer

The water pump is cracke,. replace the water pump. Peter

Posted on Mar 18, 2009

  • 5 Answers

SOURCE: My Maytag Neptune MAH5500B has water leak problem.

Is the boot completely secure and not ripped or torn? The boot is the grey seal-like area that covers the drum. If it is torn at all, the water from whatever cycle, depending on when the water seeps through will end up on the floor.

Posted on Apr 12, 2010

Testimonial: "Thank you for your advise! I saw some rips in the boot. I have ordered a new one to replace."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer leaks


There is also a discharge lint filter on the front lower left that has to seal properly. If the water appears only when washing, you can probably eliminate leaking from the water supply side up to the solenoids controlling the water. The most likely source is a leak in the rubber section between the tub and the front door, a leak in the seal between the door and the washer, a leak or overflow in the soap dispenser, or a leak in the discharge side components. You could probably figure out the source if you could view these areas during a cycle, but that would require some disassembly of the cabinet so that you would need to know what you were doing.

Jul 13, 2014 | LG WM2101H Front Load Washer

1 Answer

Frigidaire gallery series Model GLGH42FS1 stackable washer leaking


see this causes and fix it. God bless you
Water Inlet Valve
If the hose connections are good to the water inlet valve check that water is not leaking from the valve itself it is replace the water inlet valve.

Drain Pump
Check the drain pump housing and all hose connections. The drain pump is down under neath. To disassemble your washer follow the appropiate tutorial. Hoses can be tightened. If hoses or pump housing is leaking replace the pump assembly.

Tub Seal
This is in the center of the tub. The seal is inexpensive but will require some labor to install. Check the tutorials on disassembling the cabinet then remove the agitater and inner tub. Enter your model # above for a diagram or illustration.
10_12_2012_10_37_02_am.jpg

Oct 11, 2012 | Frigidaire Washing Machines

1 Answer

Washer leaking


fix it. God bless you
Water Inlet Valve
If the hose connections are good to the water inlet valve check that water is not leaking from the valve itself it is replace the water inlet valve.

Drain Pump
Check the drain pump housing and all hose connections. The drain pump is down under neath. To disassemble your washer follow the appropiate tutorial. Hoses can be tightened. If hoses or pump housing is leaking replace the pump assembly.

Tub Seal
This is in the center of the tub. The seal is inexpensive but will require some labor to install. Check the tutorials on disassembling the cabinet then remove the agitater and inner tub. Enter your model # above for a diagram or illustration.

Sep 25, 2012 | Washing Machines

1 Answer

I have kenmore washer. when I open door, I found water in there. So i drain water and washed. After two day, I found same level water in cabinet. I think water leak in side or didn't operate water presure...


If the machine is not pumping the water out during the spin cycle, then it could be a couple of things. First, it could be that the cycle timer is faulty and needs to be replaced, or it could be that the water pump is bad and that needs to be replaced. Either way, the repair is cheaper than a new machine.

Mar 07, 2011 | Kenmore Front Load Washer

1 Answer

Maytag Model A506 Series 04 Serial 201072 VA, no owner or service manual available. How does the machine cabinet open up? There is a hinge for the top to lift open, but how does one release the latch? ...


If your Maytag is a typical top loader, you insert a putty knife at the front to release the latches. Try going to www.repairclinic.com and entering A506. With luck, you will see a list of common repair parts and may be able to view a generic Maytag video showing disassembly.

Aug 12, 2017 | Washing Machines

1 Answer

My Kenmore 800 series washer is leaking water all over the floor and i can't find where its coming from. It only leaks when its on and running. I tried to take the back of it off to see where it was coming...


Some of theses models have a tendency of leaking out the side of the pump housing. In this case you will need to replace it. Here is a link to help disassemble and acess the pump.

Disassembling a whirlpool style washer

Oct 13, 2010 | Kenmore 22422 Top Load Washer

1 Answer

Kenmore 70 series, 110 washer leaks water when


Hi, You will need to change the inlet mixer valve. It is sticking open just enough to allow water to drip through it. This should be chandes asap so that it doesn't get bad enough to over flow the washer.
Here are directions on how to remove the cabinet so you can get to the inlet valve.
Removing the cabinet. UNPLUG the washer. There are two screws holding the control panel to the cabinet. Most models the screw are in front but, some models have the screws in back. They are on each end. Now raise the control panel up and let it rest on the hinges. Unplug the lid switch harness and locate the clips on each side (bronze in color) and release them.
Now the cabinet will lift off the frame and you can set it aside.
Please let me know if this helps you or if I can assist you further.

Thanks
Vic

Jul 14, 2009 | Kenmore 22422 Top Load Washer

1 Answer

LEAKING WASHER


your pump is leaking ,,, take the 2 screws out thats on each end of the console in front and pull forward and up, take the 2 hold down clips off and tilt cabinet forward and remove / pump is at bottom with 2 hoses connected to it / if you need help getting a pump let me know and send me the complete model number from under the lid and i will see if i cant help you out / larry

Dec 12, 2008 | Whirlpool LAB2700ML Pedestal Drawer for...

1 Answer

Drain hose leak


Hi Krazytech here, You will have to remove the cabinet to get to the pump end of the drain hose. First you must remove the top insert a putty knife to open the top lift up then remove screws that hold on the top then remove the screws that hold on the bottom. then you can get to the pump I alway replace the factory spring clamps with a screw hose clamp they are much better.. let me know

Aug 24, 2007 | Maytag MAV7600 Top Load Washer

Not finding what you are looking for?
Maytag PAV2300 Top Load Washer Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...