Question about K2 Women's Cinch Tryst Snowboard Bindings '09

1 Answer

Unable to update the software

Am unable to update the software in ipod. And no details abt the service center in bangalore

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 121 Answers

???????????????

Posted on Oct 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Should all pistons be at the same position - 95 polaris xlt triple


by the same position do you mean top dead center , the answer to this is NO if all the cylinders (2-4) are at TDC then the pistons would have to fire all the same time , I doubt this be enough to rotate the crank shaft thru one revolution, this is the simple reason that they invented the simple 30* Vee engine (millions of em) as this is the perfect angle to produce a circular motion in a crank shaft

Feb 02, 2016 | Snowboarding

1 Answer

Whats with all the un answered questions???


FixYa is a world-wide community of volunteers. At any given time some of us are asleep or at work or otherwise unable to answer questions.
Some questions don't provide enough details to be answered, such as your first question where you didn't bother to give the make and model of your phone.
Some questions simply can't be answered.

Oct 17, 2014 | Snowboarding

1 Answer

2012 skidoo tundra 550f


water damage, short, wonky software. bleep bloop blorp

Mar 12, 2014 | Snowboarding

1 Answer

Where to order replacement strap for Emsco ESP Youth Suprahero Snowboard, where to order?


http://www.emscogroup.com/customer-service/
I called the customer service number and spoke with a representative who asked me to send her a picture of our board. On receiving my photos she is going to send out a new strap. I'm sending the photo shortly.

Jan 06, 2014 | Emsco ESP Youth Suprahero Snowboard

1 Answer

I hav a Burton Audex link jacket. I have a problem with the audex system. The control panel automatically switch to discoverable after aprox 10 seconds of turning it on then won't access the menus again....


id check the cables, they may be damaged, try it with the jacket flat on the floor. ive gone through 4 jackets all with bad wiring, unfortunately Burton doesn't have any more warranty replacement jackets...

Nov 14, 2010 | Burton Audex Pi Mp3 Mens Xl Pimp Snowboard...

1 Answer

How do i remove the drive clutch on an indy sport touring 440 1996


you need a clutch puller, Take out the center bolt and the clutch puller will thread into the same hole,as you tighten it up it pulls the clutch off; Good luck

Jan 26, 2010 | Polaris New Genuine Polaris Snowmobile...

1 Answer

2000 indy 500 only runs on choke at times, some times it runs fine


check the carbs. It could be they need to be cleaned. To do this pull them off and flip upside down pull small philips head screw then big center bolt....set carb bowl aside then with very small screw driver pull jets and check for blockage. You should see light through these if not carefully blow through them and recheck. make sure you clean them all This should be done every year and can cause engine to lean out and blow up.

Jan 10, 2010 | Polaris New Genuine Polaris Snowmobile...

1 Answer

Snowbard bindings adjustment


"With everyday use, the screws, nuts and bolts that hold the highest stress areas together tend to loosen up. Consequently, they need to be tightened regularly to ensure that a strap doesn't fall off and get lost. However, not every Mountain Resort provides tool stations, so it's important to have a Snowboard Tool within reach (preferably in your pocket) at all times. Remember, a snowboard tool is a small investment that will definitely pay off over years of riding. Also, with the standardized insert pattern of snowboards, and with the built-in adjustment capacity in most Bindings, Mounting and Adjusting Bindings has become simple quite a simple task. To be able to do this, make sure you have a screwdriver and a wrench or two. Also, it would be a plus if you have some basic knowledge about the stance width, stance location and stance angle. The distance between your front and rear foot is the Stance Width. The basic stance width is roughly the length of your shoulder-width apart (about 30 per cent of your height). The location of the center point between your Bindings relative to the center of the snowboard is the Stance Location. Conversely, the angle of the Bindings across the snowboard's longitudinal axis, wherein zero degrees represents a line that is perpendicular to the snowboard's length, is the Stance Angle. * Forward Lean For starters, check your board's Forward Lean. The forward lean is the amount of forward angle on the highback support. For more leverage and more responsive heelside turning, add more forward lean. By adding forward lean, you also force your knees to bend, consequently ensuring a good riding stance. Still, too much forward lean makes your knee bend too much. Over bending your knees put pressure on your quadriceps muscles and reduces your ability to turn easily. So don't overdo it. You can usually adjust the forward lean in soft-boot Bindings by changing the position of a plastic stay behind the highback. * Rotating the Highbacks You can easily rotate your Bindings' Highbacks if your bindings have slots on the hinges where the highbacks are fastened to the binding's baseplate. To make your heelside turning more responsive than when it is angled along with the baseplate, adjust your Bindings in parallel with the Snowboard's Heel Side Edge. You can do this by loosening the bolts and rotating the highbacks. * Adjusting Strap Position Generally, this involves unscrewing the straps from the baseplate and moving them forward or backward on the Bindings. To improve control, move the straps higher up on the foot. Conversely, move them down lower to increase flexibility. Make sure that the toe strap is resting around the base of your toes and is securely holding down the tip of the boot. Shorten your straps if you find yourself pulling on them for a snug fit. You can do this by fastening the straps to the baseplate further along the length of the strap. Most straps already have extra holes for this adjustment."

Dec 01, 2008 | Flow M9 Snowboard Binding

Not finding what you are looking for?
K2 Women's Cinch Tryst Snowboard Bindings '09 Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top K2 Snowboarding Experts

gbob59

Level 3 Expert

2963 Answers

yadayada
yadayada

Level 3 Expert

61292 Answers

Lawrence Oravetz

Level 3 Expert

7686 Answers

Are you a K2 Snowboarding Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...