Question about Washing Machines

Open Question

Cosa vuol dire errore f 06 su whirlpool 6th sense awt9080.1

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: F9/FA Whirlpool 6th sense frontloader washer

F09 is "overflow failure" - check drain pump, pressure switch, blocked drain.
FA is the emergency shutoff switch that detects when water is pooling underneath the machine.

Posted on Jul 16, 2008

  • 1 Answer

SOURCE: whirlpool 6th sense front loader awm 8121

my whirlpool 6th sense will not start all lights and power i think that it is the door sensor at fault? The green light door locked light is not on.

Posted on Aug 17, 2008

richardsimpl
  • 230 Answers

SOURCE: Getting faulf code F06 on Whirlpool 6th Sense AWM 8143

Hi There
I have found what you looking for and i hope this help's yo. let me know.
F/06 Drive Motor Tachometer Error
The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes.

  • Check wire harness connections between the Drive Motor/Tachometer and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU)
  • Check the Drive Motor
  • Check the MCU
  • Check the Wire Harness
Thank you for writing to fix ya.
Best regards Richard

Posted on Dec 12, 2009

  • 1 Answer

SOURCE: I have a whirlpool 6th

f13 is a problem with the door lock, I have the same machine and it takes 4 minutes for the door latch to open and if it dont in the 4 minutes F13 comes up and the machine will go off and not start again.

Posted on Oct 21, 2010

sonicboomele
  • 1557 Answers

SOURCE: Am getting FP error message

your right the error code is filer pump now disconnect power and let unit sit for 1 hr should reset its computer


dam computers

Posted on Dec 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Errore f02 modello awoe 8104


open the bottom tray door on front panel 3 screws on bottom front.
clean out the trap

May 10, 2014 | Whirlpool Washing Machines

Tip

Tumble dryer not heating how to fix heater, thermostats, Ntc sensor.


We have all these tutorial guides that will help you with your Whirlpool 6th sense
How to clear error codes
Tumble dryer not heating how to fix heater, thermostats, Ntc sensor.
How to service a pump unit on condenser tumble dryer.
How to replace belt, motor or bearings.
Tumble Dryer Not Turning, How To Replace Capacitor
We have all repairs guides on these Whirlpool 6th sense Tumble Dryers
http://www.how-to-repair.com/help/tag/6th-sense/

on Jan 21, 2015 | Whirlpool Dryers

2 Answers

HOW DO I LOCATE THE HEATING ELEMENT ON THE 6TH SENSE DRYER


take the back panel off it is located in the rear.

Mar 19, 2010 | Whirlpool Dryers

1 Answer

Getting faulf code F06 on Whirlpool 6th Sense AWM 8143


Hi There
I have found what you looking for and i hope this help's yo. let me know.
F/06 Drive Motor Tachometer Error
The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes.
  • Check wire harness connections between the Drive Motor/Tachometer and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU)
  • Check the Drive Motor
  • Check the MCU
  • Check the Wire Harness
Thank you for writing to fix ya.
Best regards Richard

Dec 11, 2009 | Whirlpool Washing Machines

2 Answers

Dryer not heating, still tumbling


your heating element could be burned out...or a thermal switch could be stucknot allowing the element to turn on

May 25, 2009 | Dryers

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...