Question about JVC Rx 5020v Stereo Receiver

1 Answer

I spilled a liquid in my jvc rx-502ov receiver and a message reads dsp micom ng what do i do?

I accidentily spilled a liquid in my reciever,and when i turn it on a message reas dsp micom ng,what does that mean?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 256 Answers

You fried the poor thing to put it mildly, Get a different one end cut down on your partying ,(GUY) Unless you have money to burn

Posted on Dec 06, 2012

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
dunnbiker
  • 8546 Answers

SOURCE: Jvc RX 8020 receiver won't

I'd suspect one of the controls that would be overriden by analog direct is unknowingly activated. LOOK at the front panel and interpret every indicator for how it could cause silence. Refer to the manual for those you don't understand.

Any Tape Monitor activation would disable digital sources completely.

See page 14 for how Line Direct affects DSP modes.

Posted on Jun 27, 2011

  • 3 Answers

SOURCE: JVC RX 6042

just google jvc go to customer service at the bottom look up manuals and u can print it right off the internet no cost

Posted on May 18, 2008

VOTIT
  • 2071 Answers

SOURCE: JVC A/V Receiver RX 7042S - DSP NG

it seems the problem of your unit is in the power amplifier section,the IC chip there is defected that why only analog source .you better bring back to them the unit it is the only option, that is there back job...

Posted on Jul 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the microcomputer located in the jvc rx6030v?


Hello
The microcomputer, otherwise called as system control can be located on its main board. Some sets will have it on its front panel baord, along with the display unit board.

Feb 07, 2012 | JVC RX-6030V Receiver

1 Answer

Jvc RX 8020 receiver won't play when in DSP or Surround modes no sound at all, can only get sound in analog direct. Owned for 6 yrs. first problem ever!


I'd suspect one of the controls that would be overriden by analog direct is unknowingly activated. LOOK at the front panel and interpret every indicator for how it could cause silence. Refer to the manual for those you don't understand.

Any Tape Monitor activation would disable digital sources completely.

See page 14 for how Line Direct affects DSP modes.

Jun 27, 2011 | JVC RX-8020V Receiver

1 Answer

What rca jacks do i use to hook up for surround sound


heres the manual for your receiver it has a built-in Surround Processor on DSP mode,, but the instructions are here,, http://resources.jvc.com/Resources/00/00/96/LVT0141-001A.pdf Please take a moment to rate my reply and research for your question, Thanks Good luck

May 08, 2011 | JVC RX-558V

1 Answer

How connect to tv


http://resources.jvc.com/Resources/00/00/96/LVT0380-001A.pdf this is a manual for the rx 6000 it's the same connections as my reciever pioneer hope works...............video out to TV, all components video in to receiver

Feb 20, 2011 | JVC RX-884V Receiver

1 Answer

I have a JVC RX-801VBK. When I turn the power on it clicks on and shuts of. please help


the problem is probably a bad power transformer that will need to be replaced the best way is to contact JVC and they will be able to help you more. it may be easier to purchase a new reciever.

Jan 02, 2011 | JVC RX-8010V Receiver

1 Answer

JVC RX-6042S shuts down after 5 seconds


It will be one of the transistors that regulate the lower volatges (5V, 12V...)
I ffixed mine. the heatsinking on those transistors is pathetic, and its no wonder they dont last.
Mine was the 5V circuit, which also supplies the DSP board. so if you are getting a DSP NG, that could be that as well.
Check Q1434 and Q1404. if one is faulty, it drags the other one down with it.
Good luck.

Dec 27, 2009 | JVC RX-6042 Receiver

2 Answers

The sound cut off for a few seconds when the reciever warm up


mine did this too, just before the dsp board went. start looking.

Jan 10, 2009 | JVC RX-6040 Receiver

1 Answer

JVC A/V Receiver RX 7042S - DSP NG


it seems the problem of your unit is in the power amplifier section,the IC chip there is defected that why only analog source .you better bring back to them the unit it is the only option, that is there back job...

Jul 03, 2008 | JVC RX-6042 Receiver

1 Answer

JVC RX 6042


just google jvc go to customer service at the bottom look up manuals and u can print it right off the internet no cost

Apr 02, 2008 | JVC RX-6042 Receiver

Not finding what you are looking for?
JVC Rx 5020v Stereo Receiver Logo

Related Topics:

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Audio Players & Recorders Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

The Knight
The Knight

Level 3 Expert

75581 Answers

 Grubhead
Grubhead

Level 3 Expert

5487 Answers

Are you a JVC Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...