Question about Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore 90 series Water pressure turning up and down

Kenmore 90 series washer - when set in auto water temp cold/cold the water seems to be turning up and down as it fills. It does not stop filling early, just pulses up and down. All other functions seem okay.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 113 Answers

It will switch from hot to cold and back and forth trying to regulate the temp. You probrbly have more pressure in your cold water line than your hot or vise versa. This will cause it to seem to pulse. Dave www.washermd.com

Posted on Jan 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a kenmore 90 series, while filling..it's all hot and very little cold. I've checked the outside lines and their clear. So now I'm going inside, any thoughts?


newer washers have a thermister on water valve meaning water temp usualy between 42 and 92 degrees in the tub is the flow of water normal

Jan 23, 2011 | Kenmore Washing Machines

1 Answer

Kenmore 90 Plus Series washer washer takes forever


is the cold water all the way on?

if so, the first thing to do would be to check the screens in the cold water fill hose and the screen in the cold side of the water valve on the back of the machine. if that is not the problem then replace the water valve.

(turn the water off before taking the hose loose)

Jun 16, 2010 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

I have no water pressure on my kenmore +90 series washer. Pressure from hose is fine.


Turn off the water. Remove the hoses from the back of the washer and clean out the filter screens in the water valve.

Dec 29, 2009 | Kenmore Washing Machines

1 Answer

Kenmore 90 Series Washer : cold water fills at just a trickle:


your hot water goes through the water heater so contaminates settle in the heater. the cold does not, there is a screen inside the fill valve where the hose hooks to the valve on the machine. if this in not plugged then the fill valve will have to be replaced. because of the build up of contaminates..

Jul 08, 2009 | Kenmore Washing Machines

1 Answer

Kenmore Washer 90 series cold water trickle


Hi, You need to remove the fill hose and see what is plugging the inlet valve screen. This should make a guge difference.
Please let me knwo ig I can assist you further.

Thanks
Vic

May 23, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Cold water starts and stops when washing


sounds like your washer has an auto temp. control if so the washer mesures the temp of the water and put in the manufacture set temp for that setting this board could be bad alowing only cold water to come into the machine. you could also have low hot water pressure at the washer be sure the hot water is turned all the way on. you may want to check to make sure no trash is in the hot water side of the water valve there is a screen in there where the hose conects you can remove that screen and clean it im sure one of these solutions will help you

Jan 19, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore 90 series Clothes washer


there are filters in the fill hose which could be blocked but usually the fault is low water pressure

Aug 31, 2008 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore wash macine


its in your cold water line valve to the washer if it works good with hot water the valve are incoming line being blocked when you turn it on the pressure comes in fast then when pressure is gone water slows down so when its off the pressure builds back up it runs fast then slow

Feb 27, 2008 | Washing Machines

3 Answers

Kenmore heavy duty washing machine 70 series


The most likely cause for water fill temperature problems is the solenoid has burned out, usually cold first, it gets used more. Not a repairable item , easy to replace

Dec 30, 2007 | Kenmore 24032\24036 Top Load Washer

1 Answer

Hot/Cold water knob will not work on washing machine


Does the water flow when you have it on warm or cold settings?  If on warm setting and water flow is cold, its probably the mixing valve.  This part isnt that expensive, and not that hard to replace.  Remove the two front console caps, remove the two console hold down screws then flip the console out and then over the top.  You will see two gold cabinet hold down clamps, pop them out, the lift the whole cabinet off the unit.   You will see the mixing valve right where the inlet hoses connect to the machine.  Let me know if you need further help.

Oct 16, 2007 | Washing Machines

Not finding what you are looking for?
Kenmore 24032\24036 Top Load Washer Logo

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Fred Sops

Level 2 Expert

271 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...