Question about Toshiba COPIERS E-STUDIO 520 Copier

2 Answers

Close front cover

When I turn on the copier I get a single message. "close front cover". All covers are closed.

Posted by on

  • Anonymous Mar 18, 2014

    broken when i close the cover that is covering the ink

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

THERE IS A PROBLEM WITH ONE OF THE COVER SWITCHES. EVERY COVER HAS A SWITCH, ONE OF THEM MAYBE STUCK, BROKEN, OR MISSING. GOOD LUCK.

Posted on Apr 24, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Front cover switch normally brakes or gets pushed in too much inside... you will need to open front cover and takeoff switch cover and adjust back in place.

Posted on Jul 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Close Front Cover For Toshiba E-studio 350


There are many possibles that can cause "Close Front Cover"
Check the front cover actuator, switch. If all covers, switches is working fine, probably power supply is faulty.

Dec 02, 2015 | Toshiba e-Studio 350 Copier

Tip

Main Error MINOLTA DI 1611, DI 2011 Messages and Their Remedies


PAPER JAM A paper misfeed occurred in the
main unit.
Open the cover at the indicated
location, and then remove the
misfed paper. (“When the Message
(Flashing alternately)
OPEN XXX SIDE COVER
All misfed paper was not removed
from the main unit.
Check the message in the display
for the location of the paper misfeed,
and then remove the misfed paper.
ORIGINAL DOC.JAM A paper misfeed occurred in the
Document Feeder.
All misfed paper was not removed
from the Automatic Document
Feeder.
Open the Document Feeder Cover
and the Document Feeder, and then
remove the misfed paper.
(Flashing alternately)
OPEN DOC.FEED COVER
∗REMOVE PAPER IN
BYPASS TRAY∗
Paper is loaded in the Manual
Bypass.
Remove the paper from the Manual
Bypass.
FRONT COVER OPEN The Front Cover of the main unit is
open or not securely closed.
Securely close the Front Cover.
(Flashing alternately)
CLOSE FRONT COVER
DUPLEX COVER OPEN The Duplex Unit Cover is open or
not securely closed.
Securely close the Duplex Unit
Cover.
(Flashing alternately)
CLOSE DUPLEX COVER
DOCUMENT COVER
OPEN
The Document Feeder is lifted up
(while a document is loaded into
it).
Securely close the Document
Feeder.
(Flashing alternately)
CLOSE DOCUMENT
COVER
DOC.FEED COVER OPEN The Document Feeder Cover is
open.
Securely close the Document
Feeder Cover.
(Flashing alternately)
CLOSE DOC.FEED
COVER
TONER EMPTY The toner is empty. Copying and
printing cannot be performed.
Replace the toner bottle with a new
one.
SUPPLY TONER
PAPER EMPTY The selected paper tray has run
out of paper.
indicates the paper tray, and
“XXX” indicates the paper size.
Load paper of the specified size into
the specified paper tray.

on Dec 18, 2009 | Office Equipment & Supplies

1 Answer

Close side cover error tray


You see front cover switch if front cover knob not touch then this messege appear OR check power card & front cover connection

Nov 06, 2013 | Toshiba e-Studio 350 Copier

1 Answer

My Toshiba e-studio 233 copier is giving the error message, "Close side cover." Opening any cover to close again changes the message to "Close x" where x is the part opened, until that...


there is a switch at the side that is being push by the cover when it closes check this switch to be sure it hits the button when close or you may replace the switch it has a problem.

Jun 27, 2011 | Office Equipment & Supplies

1 Answer

Message 'Clean Sensor' has appeared. Followed advise to open Cover D and close it again but to no avail. Has anyone got any other suggestions, please?


Follow the steps below to clear the "Clean Sensor" error message.
  1. Open the front cover of the printer (cover D). c2600_cover_d.jpg
  2. Slowly close the cover again. c2600_close_cover_d.jpg This action will move the lever shown below and clean the sensor.
    c2600n_clean_sensor.png
  3. Open and close the cover several times. Once the front cover is left closed the printer will start to calibrate.
Once complete, the error should no longer appear and the printer should resume normal operation.

Note: If the error message is still apparent after following the steps above, contact Epson for further advice.

Nov 16, 2010 | Epson AcuLaser C2600N Printer

1 Answer

Canon machine message front cover is close but


there are switch behind the front door that are activated by the front cover. you may have a broken or missing actruator pin on the front door. look very carefully on the door for anything that seems to be missing. if ther is just use a piece of paper to actuate the switch. jaime

Jul 15, 2010 | Canon imageRUNNER 400S Copier

1 Answer

Error message - can not print


Try checking the little "trip switch" that is actuated when oyu close the cover. To find it, locate a small plastic tip in the cover that goes into a small hole when you close the cover. This tells the printer when the cover is opened or closed. Should be on the right or left side of the cover towards the front. The tip may have broken off OR the switch is misaligned. If the tip is there try GENTLY inserting a small screwdriver into the hole and see if that solves it. Otherwise, it is a board malfunction...

Nov 25, 2009 | Dell 922 All-In-One InkJet Printer

1 Answer

Front cover of phaser 8550 won't close correctly


You can download the service manual free at ww.eserviceinfo.com

Aug 18, 2009 | Xerox Phaser 8500/DN Printer

1 Answer

Doc. Cover Open displayed


That usually means some sensor giving you trouble.

This is what brother recomends:

How do I clear the message Cover Open or Please Close Cover from the display?


The message Cover Open or Pls Close Cover may appear if the front cover
for the drum was not closed securely. Verify the cover is closed
securely by pressing the cover release button located in the front of
the unit below the Output Tray Support Flap and open the front cover.
Close the cover until it clicks into place.

If the message continues to appear on the display verify the drum and
toner assembly is installed correctly by following the steps listed
below:

1. Press the cover release button located in the front of the unit and
open the front cover.

2. Remove the drum unit and toner cartridge from the unit by lifting it
up and out. Place it on a drop cloth or disposable paper to avoid
scattering toner.

3. Hold down the blue lock lever located on the right side of the drum
and lift the toner cartridge out of the drum unit.

4. Reinstall the toner cartridge into the drum unit by inserting it in
the drum until it clicks into place

5. Reinstall the drum unit into the unit. Make sure it is securely in
place.

6. Close the cover until it clicks into place


If that doesn't fix it, I guess you will have to talk to their support people.


Good luck!

Dec 15, 2008 | Brother MFC-8840D All-In-One Laser Printer

1 Answer

Close front cover message


Well here is what I can tell you.
Open the front cover. Staring you right in the face should be a bar code/number sticker. Look forward from that and there shoule be a small plastic tab, about a half inch long and less then the thickness of a popsicle stick. It is the front cover interlock switch actuator. It may be broken off.
Or look for the opening where that tab should slide into the machine the switch may be dislogded or broken.
Probably that tab has broken off not actuating the switch on that cover.

Dec 29, 2007 | Xerox Phaser 8500/DN Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

1,158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

pkwc

Level 2 Expert

254 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Toshiba Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...