Question about Blodgett DFG-100 Gas Single Oven

Open Question

Need to replace Johnson controls ignition control G67AG-3 on a Blodgett DFG-100-3 convection oven. I was given p/n 20348 by Blodgett, but they didn't give an answer what to do with wire #6 (24 vac

Posted by on

  • Michael Kemmerer Dec 17, 2012

    Disconnect plug causing loss of power from centrifugal sw. to control board. p/n 20348 did work after fixing plug/ socket short.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

There is a switch in bottom panel that is part of the igniter it has two wires and has a plunger type connectionype


that is a door switch which locate bottom of panel. If that close ignite will ignite, if the door open the pilot will stop. Hope it help ..good luck

Aug 20, 2014 | Blodgett DFG-100 Gas Single Oven

1 Answer

Dfg100 oven will light , get to temp, shuts off but wont light by itself again


to confirm check the Ohm draw on the temperature probe, i am not sure what is the correct one but you can check online at blodgett if probe okie then you will have an issue with the temp controller there possible the potentionmeter is worn out.....good luck

Apr 16, 2014 | Blodgett DFG-100 Gas Single Oven

1 Answer

Blodgett DFG-XCEL spark but no flame


You need at least 24 volts for the gas valve to open

Jan 21, 2014 | Blodgett DFG-100 Gas Single Oven

1 Answer

Blodgett gas oven 60-90 sec main b urner goes out


After burner on did you hear any spark ignitor if that your flame sensor is dirty or need to replace....good luck

Dec 11, 2013 | Blodgett DFG-100 Gas Single Oven

1 Answer

My company has Blodgett Gas Convection ovens, model # DFG100. Where is the serial number located on these ovens


The serial number is under the left side door behind the cover. Open the doors take out the two phillips head screws which go into the top of the lower cover, one on each end just inside the door hinge, the lower cover will remove to the front.

Jun 28, 2011 | Blodgett DFG-100 Gas Single Oven

1 Answer

Igniter stays lit entire time oven is on Blodgett dfg 100-1


I have seen this happen when a hole develops near where the ignitor is mounted. The excess gass overheats the ignitor and burns it up. What I do in a case like that is slide a c clamp over the burner and cover the hole.

Apr 12, 2009 | Blodgett DFG-100 Gas Single Oven

2 Answers

Blodgett Oven won't light


Go here,find what you seek. Great Co.
BLODGETT
44 Lakeside Avenue, Burlington, VT USA 05401
Toll Free: (800) 331-5842 Phone: (802) 860-3700 Fax: (802) 864-0183

Dec 12, 2008 | Blodgett 911-DOUBLE Gas Oven

2 Answers

Gas smell at start up


Be sure that the igniter has a good ground. I mean make sure you clean it well. Be sure its fastened well. And of course that it is close enough to burner. Air flow in building can also hinder lighting.

Nov 14, 2007 | Blodgett DFG-100 Gas Single Oven

Not finding what you are looking for?
Blodgett DFG-100 Gas Single Oven Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Blodgett Ovens Experts

Dennis Boxerman

Level 3 Expert

1144 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

joneable

Level 1 Expert

26 Answers

Are you a Blodgett Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...