Question about Whirlpool Ultimate Care II LSQ9564J Top Load Washer

1 Answer

Won't drain water for rinse

My Ultimate Care II has been a work horse for us. Today, all of sudden, it goes through the wash cycle, but when it is time to drain the dirty water for more clean water it stops. It does this for any wash cycle, i.e. permanent press, delicates. I have tried the extra rinse cycle and it starts for 3 - 4 minutes and then it stops. I have checked to make sure the hose and drain are clear. Any ideas to correct this would be greatly appreciated. Thank You.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

Your lid switch is defective..replace onthejob

Posted on Jan 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I load washer it starts the wash cycle it goes through wash cycle fine drains water but does not collect water for rinse cycle it just idles. So I turn knob to spin and it spins until done.


If it doesn't fill for the rinse, I would say that the cold inlet valve has failed. Check that the cold tap is turned on and check when the machine fills for the wash cycle and see if it is taking hot or cold water. You will probably find that it is filling only with hot water. A local spares store should have the valve you need.

Sep 17, 2015 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Whirlpool Ultimate Care II is not draing properly and water is flooding out during spin cycle.


remove the hose up where it connects to the tub and see if there isn't anything stuck there,you could still have something stuck between the tubs and it usually will end up here or you could have a damaged pump from the piece of towel you pulled out of it or there's another piece still up in between the tubs and hopefully you'll find it at the hole where the drain hose is.

Jan 22, 2012 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Stops during rinse cycle and won't pump the water out


Hi,

Problems with a washing machine not spinning or not draining are often interrelated..

If you are having a problem with your top load washer then check out thistip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkoutthis tip...

Front Load Washing machine not draining and or not spinning


heatman101

Sep 10, 2011 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool Washer - Imperial Series Quiet Wash 2


your washers drain hose is too far down the drain pipe which is causing a siphoning action pull the washers drain hose out pipe some you should be able to hear water dropping into the pipe the reason it only happens in the rinse cycle is because the water from wash is being drained and before the water vacuum is broken the rinse water comes in causing it to keep draining

Dec 30, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool Ultimate Care II keeps taking water.


ck your drain nose/drainline, chances are you have along hose, perhaps even draining along the floor behind hte unit, into a "closed" drain system. in which cawee the wwater is syphoning out during the rinse cycle, youlll needt o raise the drain hose to above 48" and have it drain into a stand pipe to prevent siphoning effect

Nov 19, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Won,t drain on rinse cycle


Ok mc we need a timer at this point. You see the timer doing several steps different than before.

Nov 01, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Washer will not Spin during SPIN CYCLES


Thanks for the question If your washer sorta spins and washes ok, your problem is with the transmissionTHanks for your question THe Appliance doc

Jul 29, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool washer ultimate care


check for problem with the pump it is coupled to the motor, if it is spinning then it should also be pumping out the water

Apr 23, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9564J Top Load Washer Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...