Question about Haier HDP18PA Stainless Steel Free-Standing Dishwasher

4 Answers

Haier HDP18PA ran ok yesterday...2 yrs old but never used until this when I press start all led flash and I get 10 beeps then lights continue silent for couple minutes then 10 beeps again??? no water turns on ....covers off and not flodded flood float switch ok (works) ANY IDEAS ??

Posted by on

  • Anonymous Jun 30, 2008

    user manuals



4 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

On another site, someone posted this: "I called (website), where it was purchased from, and they gave me the number for the manufacturer. Some standard troubleshooting did the trick and my dishwasher is working perfectly again. The troubleshooting involved tilting the dishwasher backwards at a 45-degree angle and letting any excess water drain out. They said ocassionally the water intake will be blocked and this process helps move anything that may have gotten in the way"


I was having the beeping problem too, and decided to give it a try, tipped it for a few, and found it to work!!! Hope this maybe helps!

Posted on Oct 17, 2007

  • laura_seel
    laura_seel Apr 06, 2012

    Thank You SOOOO much!!!!!! It worked.


  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

This happened to me also.I turned power off. I drained the excess water from the inlet and outlet hoses. Then I turned the power back on after 10 min or so and it's working great.

Posted on Sep 19, 2015

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It worked!!! Thank you so much! I tipped the unit back about 60º while it was running and it stopped the beeping.

Posted on Aug 02, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 883 Answers

Must contact Haier by website or phone. This is obviously a factory programmed fault code. just check your water supply first to be sure. You have enough water pressure?

Posted on Jun 09, 2007

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why Does Fault Alarm Beep at End of Cycle?

Check any user friendly ports, filters, screens. It appears that the washer is trying to tell you something. See your manual for troubleshooting. BLEEP BLOOP

Mar 10, 2014 | Haier HDP18PA Stainless Steel...

2 Answers

Dryer will not start

might need a control broad if you know how to check it out ,if u still got the mannual that came with the dry it will have a troubleshooting page you can read it will help you out are calll a appliance repair man ok

Jun 10, 2017 | Kenmore Dryers

1 Answer

I have a Sony BDP S370 and I would like to make it region free for my DVDs.

u can make your dvd for region free DVD play back. but for that you have to purchase an universal remote (ONE FOR ALL URC-7950). through this remote only you can make player DVD region free.
first of all u have to set( program) the remote for the same purpose.

Full procedure for the OneForAll URC-7950 remote is as follows:(preparing remote)

1. Press DVD
2. Hold the magic button until the Power key flashes twice.
3. Press 0533

4. Hold the magic button until the red led flashes twice.
5. Press 994
6. Press Magic key (don't hold)
7. Press 00189
8. Press 1 ( this sets it to key 1 - it flashes twice, if not repeat steps 4 to 8 )

9. Hold the magic button until the red led flashes twice.
10. Press 994
11. Press Magic Key (don't hold)
12. Press 00255
13. Press 2 ( this sets it to key 2 - it flashes twice )

14. Hold the magic button until the red led flashes twice.
15. Press 994
16. Press Magic Key (don't hold)
17. Press 00095
18. Press 3 ( this sets it to key 3 - it flashes twice )

19. Hold the magic button until the red led flashes twice.
20. Press 994
21. Press Magic Key (don't hold)
22. Press 00221
23. Press 4 ( this sets it to key 4 - it flashes twice )

24. Hold the magic button until the red led flashes twice.
25. Press 994
26. Press Magic Key (don't hold)
27. Press 00079
28. Press 5 ( this sets it to key 5 - it flashes twice )

The remote is now programmed and ready to use, to make the BDP-S370 region free

1. Use the remote that came with the player to bring the player out of standby, make sure there isn't a disc in it.
2. Press 1, 2, 3, 4, 5 on the OneForAll URC-7950 remote. The power light will start flashing. (blue middle light)
3. Put the player back into standby with the Sony remote.
4. Next time you turn on the player it will be region free for DVD playback.

Jan 13, 2011 | Sony BDPS370 BluRay Player

1 Answer

I have a haier tv that is only 2 yrs old and the power won't come on the tv. Is there a reset button or someway i can fix it myself.

Reset the tv by unplug,replug it in an hour later.Same problems,power LED light indication flashes?Tries websites like, to buy a whole refurbish power supply board for the replacement.

Aug 07, 2010 | Haier HLH406BB 40 in. LCD HDTV

1 Answer

Haier HDP18PA

Not sure of the background on your fault, but this may help:
I have an HDW202. I accidentally opened the door while it was running - a no-no, but there is no lock preventing opening the door while it is running - not idiot-proof at all, disappointing, really. Anyway, closed the door, the washer kept running, then water started to leak out the front door. I quickly turned it off, mopped up the water, and turned it back on. It pumped out the remaining water visible in the bottom, then started flashing lights and doing 10 beeps in a row, pausing for a minute, 10 beeps in a row again, etc. - it was stuck in this cycle. I tilted the unit forward, backwards, and side to side, while turning it on and off periodically to check for results. More water came out of the unit, and it started to behave normally while tilted, but not level. Eventually, after more tilting, it returned to normal behaviour when level. It seems it did not pump all of the water out initially, and this was causing it to malfunction until all of the residual water inside had drained onto the floor from tilting the unit.

Jan 25, 2009 | Haier HDP18PA Stainless Steel...

1 Answer


Tilt the machine 45-0 degrees and let it drain any excess water.. It also beeps when the leds flash also right? Drain the water and it will start right back up.

Aug 25, 2008 | Haier HDP18PA Stainless Steel...

1 Answer

My dishwasher keeps beeping at me and the first four lights on the panel are flashing, I have a Baumatic BW07.

I tilted mine backwards with it running and beeping and it stopped beeping shortly...It made a mess on the floor of course but I put it down and lights were still flashing but no more beeping. Thought I would try tipping it forward while it was running and the lights went off and the beeping never started again. Its working fine now??

May 18, 2008 | Haier HDP18PA Stainless Steel...

5 Answers

The washer keeps beeping and trying to drain as soon as it is turned on

I have a Haier HDP18PA with the same problem... I tried tilting mine backwards while running...this made a mess BUT the beeping stopped BUT the lights were still flashing. Turned it off and started it again and the lights still were flashing BUT no beeping. Decided to try tilting it forward while running ... made another mess BUT the lights stopped flashing. Turned it off again and restarted it and it is now running fine. Good luck!

May 05, 2008 | Haier HDP18PA Stainless Steel...

5 Answers

Remote codes

You can find the remote control codes for different brands of devices from

If none of the codes work then we have two other solutions:

1. Searching For Your Code

If you have tried all of the set-up codes for your brand of equipment ,or your brand is not listed, and you are still not able to get the unit to respond, try the following procedure to search for your code.
If you don't find a code that works, the remote will flash four times when you reach the end of all the codes for this device type.
  1. PRESS the button for the device you want to program, (TV, VCR, CABLE, etc.), then RELEASE.
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. ENTER 9-9-1 (two blinks on the remote)
  4. ALTERNATE slowly between the POWER key and the DEVICE (TV, VCR, CABLE, etc.) button until your device turns off. (On VCR, LD, and CD players use PLAY instead of POWER)
    Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
  5. When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.

2. Learn the buttons from the original

Line up your original remote and the head-to-head before completing the following steps.
  1. PRESS and HOLD the SETUP button until the red LED flashes twice.
  2. PRESS 9 - 7 - 5, the red LED will flash twice.
  3. PRESS the DEVICE key where you wish to learn the function. The next 3 steps must be completed within 10 seconds.
  4. PRESS the button that will receive the learned function, the LED will flash rapidly.
  5. PRESS the button on the original remote to be learned.

Now you can repeat steps 3 through 5 to learn other functions onto other keys or press and hold SETUP until the Cinema's red light flashes twice to lock in your new feature. (If the red light does not blink twice, stop and repeat steps through 6).
To test the new feature, press and release the device key in which the new feature was learned followed by the key on which the feature was learned

More help for programming your remote can be found here:

Hope that helps! Should you have any further questions, please feel free to post them here.

P.S. - If you find that the solution/answer I provided led you to, or resulted in a fix, please close the ticket with a FixYa! rating. I would be very grateful for your show of appreciation.
If it hasn’t, please do not assign a rating just yet. Please post back as to what steps you took, results, etc, and I will try to assist you further as best I can. I am here at your service.

Thank you for using FIXYA!


Sep 09, 2007 | Haier HTF20R21 20" TV

Not finding what you are looking for?
Haier HDP18PA Stainless Steel Free-Standing Dishwasher Logo

1,250 people viewed this question

Ask a Question

Usually answered in minutes!

Top Haier Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Tim Doolittle
Tim Doolittle

Level 2 Expert

114 Answers

Melissa Martin
Melissa Martin

Level 3 Expert

753 Answers

Are you a Haier Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides