Problem with converting from pol to rec... trying to convert -0.17-0.47i to polar. instead of getting 0.5,249.6 am getting 0.5,-109.

In the COMP mode (press MODE 1 to get there), press

SHIFT [Pol] (-) . 1 7 SHIFT [,] (-) . 4 7 =

[Pol] is on the "+" key, [,] is on the ")" key.

Posted on Dec 05, 2012

Hi,

a 6ya expert can help you resolve that issue over the phone in a minute or two.

best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).

click here to download the app (for users in the US for now) and get all the help you need.

goodluck!

Posted on Jan 02, 2017

SOURCE: Can I convert Decimal Degrees

Yes. Pressing the DMS key (two keys above the 8 key) when a result is displayed toggles the result between decimal degrees and degrees-minutes-seconds.

For example, to convert 3.5 degrees, press 3 . 5 = and you'll see 3.5. Now press DMS and you'll see 3 degrees 30 minutes 0 seconds.

Posted on Jul 31, 2011

SOURCE: can you show how to convert pola to rectangular o

Hello,

To avoid errors make sure that the angle unit is THE ONE required by your problem. To verify or to change the angle unit press [SIFT][MODE] and select [3: Deg] for degrees, [4:Rad] for radians, or [5:Grad] for grads.**Convert from rectangular to polar **

[SHIFT][+] (Pol) . Screen displays **Pol(**

You enter the X-coordinate, and the Y coordinate separated by a comma, then you close the parenthesis and press [=].

Exemple: Polar coordinate of the point (1,1)

Pol( 1, 1) gives

r=1.414213562 (square root of 2)

θ=45

Here is how you enter it

Press [SHIFT][MODE][2:LineIO]

[SHIFT][POL] 1 [SHIF] [,] 1 [)] [=]

The screen displays**Pol(1,1)****r= 1.414213562θ= 45 **

Rec ( radius, angle) =

Exemple: Recatngular coordinates of (r=3, θ=60°)

The screen displays

X= 1.5

Y= 2.598076211

Hope it helps.

Posted on Nov 15, 2009

Testimonial: *"thanx that was very helpful"*

SOURCE: convert from polar to rectangular

Examples #036 and #037 in the Appendix illustrate how to convert between polar and rectangular coordinates. If you need the appendix and/or the manual, you can download them from

http://support.casio.com/manualfile.php?rgn=1&cid=004001004

Posted on May 22, 2011

Convert the Cartesian coordinates to polar coordinates (r, Theta). The calculator can do that. Press the SHIFT [+] key combination. Calculator will display Pol(. Type in the Cartesian coordinates (x,y), close the right parenthesis and press [=]. The calculator will display the radius r and the angle theta.

If you want to convert from polar to Cartesian coordinates, use the SHIFT [-] (Rec) key combination. Enter the radius and the angle separated by a comma, close the right parenthesis and press [=]

Be careful, the angle unit you use (radian or degree) will affect the result.

If you want to convert from polar to Cartesian coordinates, use the SHIFT [-] (Rec) key combination. Enter the radius and the angle separated by a comma, close the right parenthesis and press [=]

Be careful, the angle unit you use (radian or degree) will affect the result.

Feb 16, 2013 | Casio FX-115ES Scientific Calculator

The Pol function converts coordinates from rectangular to polar. Pol(x,y) converts the rectangular coordinates (x,y) to polar coordinates (r, theta).

For examples and instructions, see page E-37 of the manual and example #036 in the Appendix.

For examples and instructions, see page E-37 of the manual and example #036 in the Appendix.

Dec 07, 2012 | Casio FX-115ES Scientific Calculator

No!! The only complex number operations you can perform are addition, subtraction, multiplication, and division and raise to an integer power with positive exponent. You can also get the Argument or the conjugate of a number, convert a complex number from rectangular to polar forms and vice versa.

As to matrices, it can only handle up to 3X3 dimension with real coefficients.

As to matrices, it can only handle up to 3X3 dimension with real coefficients.

May 09, 2012 | Casio FX991ES Scientific Calculator

In Run screen, Press OPTN, Press F6> repeatedly until you see the ANGL TAB. Press F6> again (once or twice). You will see the TAB Pol( and Rec(

To convert from Rectangular coordinates to Polar press POL(, type in the x and y coordinates then EXE

Example: F1: Pol(1,1) gives (1.314213562, 45)

F2: Rec(square root (2), 45) gives (1,1)

Make sure the angle unit is set to the one you need (degree or radian).

To convert from Rectangular coordinates to Polar press POL(, type in the x and y coordinates then EXE

Example: F1: Pol(1,1) gives (1.314213562, 45)

F2: Rec(square root (2), 45) gives (1,1)

Make sure the angle unit is set to the one you need (degree or radian).

Apr 19, 2012 | Casio Algebra FX 2.0 Calculator

Use the Rec function (shift of the - key).

Rec(r,t) converts a polar value of magnitude r and angle t in the current angular mode. The real value is assigned to X and the imaginary value is assigned to Y.

Use the Pol function (shift of the + key) for the reverse.

It's on page E-37 of the manual. If you've misplaced your manual, you can download a new one from http://www.casio.com/support/manuals

Rec(r,t) converts a polar value of magnitude r and angle t in the current angular mode. The real value is assigned to X and the imaginary value is assigned to Y.

Use the Pol function (shift of the + key) for the reverse.

It's on page E-37 of the manual. If you've misplaced your manual, you can download a new one from http://www.casio.com/support/manuals

May 28, 2010 | Casio FX-115ES Scientific Calculator

how can i enter a polar form number with angle to convert into a complex numbe(a+bi)

Apr 28, 2010 | Casio Algebra FX 2.0 Calculator

You can perform coordinate conversions in the COMP, STAT, MATRIX and VECTOR Modes.

Angle unit may be in either degree or radian.

To convert from rectangular to polar, (SQRT(2)/2,SQRT(2)/2)

Press [SHIFT] [+] (Pol)

Screen displays Pol(

Type in SQRT2

Use right arrow to move cursor out of radical

Type in /2 [SHIFT] [,]

Type in SQRT2

Use right arrow to move cursor out of radical

Type in /2

Close the right parenthesis

Screen displays Pol (SQRT2 /2, SQRT2 / 2)

Press [=]. Display echoes the command on top line and result in bottom line as r=1, theta =45, (if unit is in degree) or theta = 0.7853981634 if unit is radian.

To convert from polar to rectangular coordinates

Note: You cannot use the answer memory to convert back to rectangular because the calculator will use the r-value only. So you will have to enter the radius AND the angle.

ex: Rec(1,45)

Angle must be in degree

Press [SHIFT][-] (Rec)

Screen display Rec(

Type in 1 [SHIFT] (,) 45 [)] [=]

Calculator displays X=0.7071067812, Y=0.7071067812

If you press the SD key hoping to convert the decimals to radicals, the calculator will not do it.

As to the "confusion", I have found none.

After you finish entering the argument of a square root, use the right arrow to move cursor out of under the root symbol to signify that the argument is complete. If you use a left parenthesis inside the root, you must insert the matching right parenthesis inside the root, then move cursor outside the root.

This is how the calculator behaves, and I am not expressing an opinion on how simple or complicated that is. I assume that to make full use of the calculator capabilities, one has to converse with it, using the syntax it understands.

Angle unit may be in either degree or radian.

To convert from rectangular to polar, (SQRT(2)/2,SQRT(2)/2)

Press [SHIFT] [+] (Pol)

Screen displays Pol(

Type in SQRT2

Use right arrow to move cursor out of radical

Type in /2 [SHIFT] [,]

Type in SQRT2

Use right arrow to move cursor out of radical

Type in /2

Close the right parenthesis

Screen displays Pol (SQRT2 /2, SQRT2 / 2)

Press [=]. Display echoes the command on top line and result in bottom line as r=1, theta =45, (if unit is in degree) or theta = 0.7853981634 if unit is radian.

To convert from polar to rectangular coordinates

Note: You cannot use the answer memory to convert back to rectangular because the calculator will use the r-value only. So you will have to enter the radius AND the angle.

ex: Rec(1,45)

Angle must be in degree

Press [SHIFT][-] (Rec)

Screen display Rec(

Type in 1 [SHIFT] (,) 45 [)] [=]

Calculator displays X=0.7071067812, Y=0.7071067812

If you press the SD key hoping to convert the decimals to radicals, the calculator will not do it.

As to the "confusion", I have found none.

After you finish entering the argument of a square root, use the right arrow to move cursor out of under the root symbol to signify that the argument is complete. If you use a left parenthesis inside the root, you must insert the matching right parenthesis inside the root, then move cursor outside the root.

This is how the calculator behaves, and I am not expressing an opinion on how simple or complicated that is. I assume that to make full use of the calculator capabilities, one has to converse with it, using the syntax it understands.

Mar 31, 2010 | Casio FX-115ES Scientific Calculator

To avoid errors make sure that the angle unit is THE ONE
required by your problem. To verify or to change the angle unit press
[SIFT][MODE] and select [3: Deg] for degrees, [4:Rad] for radians, or
[5:Grad] for grads.

**Convert from rectangular to polar **

[SHIFT][+] (Pol) . Screen displays**Pol(**

You enter the X-coordinate, and the Y coordinate separated by a comma, then you close the parenthesis and press [=].

Exemple: Polar coordinate of the point (1,1)

Pol( 1, 1) gives

r=1.414213562 (square root of 2)

θ=45

Here is how you enter it

Press [SHIFT][MODE][2:LineIO]

[SHIFT][POL] 1 [SHIF] [,] 1 [)] [=]

The screen displays

**Pol(1,1)**

**r= 1.414213562**

θ= 45

**Convert from polar to rectangular coordinates**

Rec ( radius, angle) =

Exemple: Recatngular coordinates of (r=3, θ=60°)

**[SHIFT][Rec] 3 [SHIFT][,] 60 [ ) ] [=] **

The screen displays

**Rec(3,60)**

X= 1.5

Y= 2.598076211

[SHIFT][+] (Pol) . Screen displays

You enter the X-coordinate, and the Y coordinate separated by a comma, then you close the parenthesis and press [=].

Exemple: Polar coordinate of the point (1,1)

Pol( 1, 1) gives

r=1.414213562 (square root of 2)

θ=45

Here is how you enter it

Press [SHIFT][MODE][2:LineIO]

[SHIFT][POL] 1 [SHIF] [,] 1 [)] [=]

The screen displays

θ= 45

Rec ( radius, angle) =

Exemple: Recatngular coordinates of (r=3, θ=60°)

The screen displays

X= 1.5

Y= 2.598076211

Jan 19, 2010 | Casio FX-115ES Scientific Calculator

Hello,

To avoid errors make sure that the angle unit is THE ONE required by your problem. To verify or to change the angle unit press [SIFT][MODE] and select [3: Deg] for degrees, [4:Rad] for radians, or [5:Grad] for grads.

**Convert from rectangular to polar **

[SHIFT][+] (Pol) . Screen displays**Pol(**

You enter the X-coordinate, and the Y coordinate separated by a comma, then you close the parenthesis and press [=].

Exemple: Polar coordinate of the point (1,1)

Pol( 1, 1) gives

r=1.414213562 (square root of 2)

θ=45

Here is how you enter it

Press [SHIFT][MODE][2:LineIO]

[SHIFT][POL] 1 [SHIF] [,] 1 [)] [=]

The screen displays

**Pol(1,1)**

**r= 1.414213562**

θ= 45

**Convert from polar to rectangular coordinates**

Rec ( radius, angle) =

Exemple: Recatngular coordinates of (r=3, θ=60°)

**[SHIFT][Rec] 3 [SHIFT][,] 60 [ ) ] [=] **

The screen displays

**Rec(3,60)**

X= 1.5

Y= 2.598076211

Hope it helps.

To avoid errors make sure that the angle unit is THE ONE required by your problem. To verify or to change the angle unit press [SIFT][MODE] and select [3: Deg] for degrees, [4:Rad] for radians, or [5:Grad] for grads.

[SHIFT][+] (Pol) . Screen displays

You enter the X-coordinate, and the Y coordinate separated by a comma, then you close the parenthesis and press [=].

Exemple: Polar coordinate of the point (1,1)

Pol( 1, 1) gives

r=1.414213562 (square root of 2)

θ=45

Here is how you enter it

Press [SHIFT][MODE][2:LineIO]

[SHIFT][POL] 1 [SHIF] [,] 1 [)] [=]

The screen displays

θ= 45

Rec ( radius, angle) =

Exemple: Recatngular coordinates of (r=3, θ=60°)

The screen displays

X= 1.5

Y= 2.598076211

Hope it helps.

Nov 14, 2009 | Casio FX-115ES Scientific Calculator

Hello,

Press [MODE] and select [1:COMP]

Press [SHIFT][MODE] and select [3:Deg]. You can also use rad if the angle you are given is in radians.

To start the conversion

Press [SHIFT][-] (Rec) screen displays**Rec(**

Key in the radius r , ex: 3 screen displays**Rec(3**

Press [SHIFT][)] (,) to enter comma separator **Rec(3,**

Key in the angle in degrees, ex: 57.3; screen displays **Rec(3,57.3**

Press ) to close parentheses; screen displays **Rec(3, 57.3)**

Press [=]

Screen displays

**Rec(3, 57.3)**

**X=1.620720961**

Y=2.524532346

X and Y are the values of the coordinates. ** **

If angle is in radians, [SHIFT] [MODE][4:Rad] the command

Rec(3, Pi) gives X=-3, Y=0

Hope it helps

Press [MODE] and select [1:COMP]

Press [SHIFT][MODE] and select [3:Deg]. You can also use rad if the angle you are given is in radians.

To start the conversion

Press [SHIFT][-] (Rec) screen displays

Key in the radius r , ex: 3 screen displays

Screen displays

Y=2.524532346

If angle is in radians, [SHIFT] [MODE][4:Rad] the command

Rec(3, Pi) gives X=-3, Y=0

Hope it helps

Oct 18, 2009 | Casio FX-115ES Scientific Calculator

102 people viewed this question

Usually answered in minutes!

×