Question about Maytag Dependable Care LAT9706

1 Answer

How do you remoce the start switch on a servis caress M2010?

I need to remove the switch to replace it, but cant get it out. Can anyone help?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 45 Answers

It's probably a broken lid switch.. There's probably an ovular hole under the lid on the right side. Here's a helpful link to access it.

http://www.applianceaid.com/procedures.h...

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washing Machine does not start


It could also be your line to the machine is fried at the ends where the electrical hook up is. Look at the connections on the back of the machine. One may be fried

Feb 21, 2014 | Washing Machines

1 Answer

Servis washing machine one of the buttons on the control panel have pushed in and won't work anyone know if this can be repaired?


You can switch off the washer and remove the panel carefully, The buttons are normally held by small plastic hinges and it could have been damaged. You can remove the switch panel from inside and keep the buttons in place with a soft glue before the board is replaced back to place.

Aug 22, 2013 | Washing Machines

1 Answer

My Servis 1300 AA wont start properly, the start button just keeps flashing. We have got it working a couple of times by repeatedly whacking the door but its not the solution! any help would be great...


It is possible the the door switch has failed and so unless this switch contacts when closed the program will not start as a safety measure for filling water to the tub.
So remove power and slide the machine to check the door switch for continuity , you can short to test this switch before replacement.

Jul 05, 2012 | GE Washing Machines

1 Answer

User manuals for: Hoover soft wave model number HSWD 126-80 and Servis washing machine Caress 1000A, model no: M3101A If someone could help that would be great :-)


Hi from retired Englishman in SW France,

Manual
You will need to type into your search engine/web browser '(make model number) washer manual' and you should be presented with a number of sources from which you can either download for free or have to pay a nominal amount.
You could also try the manufacturer's web site direct ;-0)

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C.

Sep 22, 2011 | Washing Machines

1 Answer

Manual instruction for servis caress 1200 a


i want to connect a hot water to my caress1000`a`
is it possible?and how our washing machine could control the temperature.(washing machine has a cold water connection)

Aug 31, 2010 | Washing Machines

2 Answers

Can I get a a circuit diagram for a Servis caress 900 washing Mac


Their is usually a wireing scmetac inside the timer and switch housing of most machines.

Aug 25, 2009 | Washing Machines

1 Answer

My servis easi logic 1400 doesnt switch over in cycle.


Check the control card for dry joints. This is a common problem with these machines

Jul 04, 2009 | Washing Machines

1 Answer

Orientation of inlet pipes


I am not to sure if this answers your question but I think you are asking which way the hot and cold hoses connect to the wasing machine? if this is the case if you look on the back of the washing machine you will see stamped in the metel a H for hot connect the hot water inlet hose to this, If it is not marked, hook up the hot water hose to the washing machine and place the water temp selector to hot and turn machine on if hot water comes out you have the correct hose hooked up,if not then the cold water hose goes were you hooked up the hot water hose. hope this helps

Jun 24, 2009 | Washing Machines

1 Answer

My servis caress 600 will not spin on any programe it has been moved recently is there something i need to do, can someone help thankyou


Most washing machines have a safety switch on the lid. If that switch has been broken or a wire fell off then closing the lid does not close a safety circuit and will not allow the machine to enter the spin cycle.

1st make sure the switch is getting depressed when the lid is closed. I am not familiar with your exact machine. On my Whirlpool I can take a screw driver and push the switch in while the lid is open and get the spin cycle to occur. Be careful to not have anything in the machine and keep all hands and any item you might be wearing away from the drum so it does not get caught in the spinning with the lid open. The location of the switch will very, but on mine it was on the right side, on the lip of the opening. There was a **** in the sheet metal in which a flat piece prong slid through when the lid was closed. Let me know if you need a picture and I can post a link to what it looks like on my machine.


2nd if that does not work then you may need to remove the switch and verify it is working. Unplug the washing machine from the electrical outlet. Place an Ohm Meter/Continuity tester across the switch electrical contacts. Activate the switch and you should be able to see that the switch opens/closes its electrical contacts. If it does not, replace the switch with a new one.

You can easily find replacement switches off the internet or your local appliance parts store. You will need the make and model # of your washer when ordering the part. I would check several places. I have found prices very greatly. I would expect the part to be less than $20.

Hope that helps.

Oct 24, 2008 | Washing Machines

1 Answer

Servis 1200A caress washing machine trips electric


A wiring harness may be loose and the vibration has worn through the insulation. Put it on the side and take a look for loose wires and rubbing.

Oct 30, 2007 | Maytag Dependable Care LAT9706

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Al Clark

Level 2 Expert

290 Answers

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...