Question about General Electric WDSR2120J Top Load Washer

Open Question

Ge washer wdsr2120j

Wont stop filling up with water, won't rinse or spin

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Does not advance from wash to rinse to spin

The washer is new and under warranty so I have asked for warranty service.

Posted on May 24, 2009

Ad
  • 97 Answers

SOURCE: We have a GE top load washer with the model number

Hello Friend, You either have a bad water level/pressure switch or your water inlet valve is bad. If you unplug the washer from the wall and the water stops filling into the washer, then it's not the water inlet valve. If it only continues to fill when wash cycle is started then you will need to replace the water level/pressure switch behind control panel. Also, the pressure supply tube connected to water level/pressure switch may have a hole in it or a bad connection, or possibly plugged up. This rubber tube must have an airtight seal at both ends to perform properly. be sure to check this item also. Happy to help, Tim.

Posted on Jul 01, 2009

  • 1 Answer

SOURCE: washer will not spin out water but turns during wash cycle

Try cleaning out the trap. It is located under the door and can be accessed be removing three screws at the base in the very front of the washer. The trap is white and screws to open. Watch out though, because if the washer is full of water it will come spilling out! With the trap removed, you should also use your finger to feel the opening of the pump to the side. I found a few bobby pins in my pump, and once they were removed it worked again!.

Posted on Jan 31, 2010

  • 4088 Answers

SOURCE: GE WDSR2120J wash cycle sound

It's possible that the tub suspension system is out of position. Open the cabinet top (use a thin putty knife in each front corner to release a spring clip) and watch the mechanism while washing. Try shaking the assembly to see if you can spot something rubbing. Hope this helps!

Posted on May 23, 2010

Testimonial: "Quick response with clear verbose guidance. Thank you so much :)"

  • 1 Answer

SOURCE: No water no Spin

Check your 2 in 3 out water valve part# WH13X10029, this responsible for filling of water. By the way wash cycle will not run, until washer sense enough water.

Posted on Aug 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WDSR2120J washer will not fill in rinse cycle


possible 3 solutions for this problem 1 could be the cold fill solenoid 2 could be brushes in motor 3 could be main pcb

Feb 20, 2013 | Washing Machines

1 Answer

My GE SpaceSaver Washer/dryer will wash, but when it's time to rinse and spin the machine stops. It will not drain, riinse , or spin.


It is possible that the machine does not start off the cycle because there are errors due to feedback from the inputs. For the program to start up the main program controller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting from the flow of water into the drum as also the drain valve to open to exit the water at the point of the program cycle. If this does not happen then the voltage at the valve/motor/pump must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

Jul 27, 2012 | GE Spacemaker Washer and Dryer Electric...

1 Answer

Water won't stop filling the washer


water fill valve is probably stuck open. see if you can find a blockage or just replace it

Feb 03, 2012 | Kenmore HE2 Washing Machines

1 Answer

My maytag mtw5600tq1 washer won't hold water. Its


Hi,
Its sounds like you have a siphon going on, this happens when the drain hose it too low during fill and as the water enters the unit it exits through the drain hose. To stop this the drain hose needs to be higher than the tub itself, meaning: raise the drain hose behind the washer to about control panel area. This will or should stop the siphon effect and allow the water to remain in the tub. If the drain hose is low this siphon will start again.
I hope this helps

Aug 26, 2011 | Maytag Washing Machines

1 Answer

I have a GE washer that during the spin cycle / rinse on my washer the water won't shut off and will run and run until I turn the water valve off. This occurs during spin cycle when it adds water but...


water valve or water presher switch my vote is water valve start washer when water is filling unplug from wall if water is still running it is the water valve if water stops it has to do with presser switch let me know what happens I will walk you threw how to repair thanks

Jun 24, 2011 | GE WPGT9360EPL Top Load Washer

1 Answer

My washer fills with water on starting a load but then it does nothing won't start spining to empty water


If the machine loads ups with water and does not stop then the water level sensor is fautly . But if the inlet valve stops on fill up but there is no spin of the motor or thereafter there is no spin/rinse or drain then the program controller / drain valve/pump must be checked.

Jun 14, 2011 | Washing Machines

1 Answer

We have a GE top load washer with the model number WDSR2120J. It new (almost 13 months old so the warranty has just expired.) When we turn it on, it won't stop filling up when it is full. Bubbles then come...


Hello Friend, You either have a bad water level/pressure switch or your water inlet valve is bad. If you unplug the washer from the wall and the water stops filling into the washer, then it's not the water inlet valve. If it only continues to fill when wash cycle is started then you will need to replace the water level/pressure switch behind control panel. Also, the pressure supply tube connected to water level/pressure switch may have a hole in it or a bad connection, or possibly plugged up. This rubber tube must have an airtight seal at both ends to perform properly. be sure to check this item also. Happy to help, Tim.

Jul 01, 2009 | General Electric WDSR2120J Top Load Washer

2 Answers

Washer will fill fill with water but doesn't start wash cycle


it will fill but won,t spin, will throw out water as if it washed, then it take water to rinse but won,t spin ,then will throw out water as if it did , but clothes are soaked

Feb 21, 2009 | Roper RAS8445KQ Top Load Washer

2 Answers

Won,t drain on rinse cycle


There could be several causes for this, but probably a bad timer. One test for this...when it stops...is to turn it off...and turn the timer slightly clockwise...to the middle of the rinse cycle...and turn it back on. Does it run then?? Try advancing it to the spin cycle after the rinse. If it runs okay after you manually advance the knob...the timer is probably defective.

Jan 13, 2008 | GE WNCD2050AWC Top Load Washer

Not finding what you are looking for?
General Electric WDSR2120J Top Load Washer Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top General Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Oloyede Monsuru

Level 3 Expert

1417 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a General Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...