Question about Samsung HCM4215W 42" Rear Projection Television

1 Answer

Samsung hcm4215w keeps blowing conv resistors

Hi i have this tv and replaced rz142 and rz143 and the stk 392-040 next to those resistors.....the same 2 resistors keep blowing as soon as i power the tv on and try to do convergence......

i didnt repalce the other stk since i didnt think it has anything to do with the res blowing...prior to this happening i couldnt move blue up or down...everything else worked fine....and when i originally checked the rz142 143 they were both blown so i replced them and they blew again so i repalced them and the stk 392-040 right next to the two res and they blew again but i didnt repalce the other stk......

Posted by on

  • 7 more comments 
  • dcxguy48080 Jan 11, 2009

    these resisitors are convergence resistors usually bad stk cause them to blow..but i replaced the stk and they keep blowing the same 2 resistors

    rk142 and rk143 on the convergence board........i just want to know what could be causing these to blow all the time instantly


  • dcxguy48080 Jan 11, 2009

    could you tell me if rk142 and rk143 are 3.9 ohm 1 watt??

    thats what i keep repalcing them with and they blow everytime


  • dcxguy48080 Jan 11, 2009

    well ii look slike they should be 3.9 ohm 2 watt......is that correct And if so if i use 3.0 ohm 1 watt would that cause them to blow??

  • dcxguy48080 Jan 11, 2009

    yes it says 3.9 ohm 2 watt..........i dont have any

    can i uses 2.2 ohm 2 watt and try that???

    the 3.9 ohm 1 watt i have kept blowing




  • dcxguy48080 Jan 12, 2009

    i have replaced the stks.......and there is no pico fuse on the convergence board......where is fd102 at?

  • dcxguy48080 Jan 12, 2009

    i coukld not see any pico fuse at all on the convergence board

    usually they are green..........but nothing there..


  • Shahid Electronics
    Shahid Electronics May 11, 2010

    you should use 3.9 2w resistor as recommended in schematics. alternate part can cause of more damage. if you still want to give a try, can do it at own risk.

  • Shahid Electronics
    Shahid Electronics May 11, 2010

    Resistor value should be as per service manual specifications. I do not have this particular model schematics thats why asked you, do you have its service manual?

  • Shahid Electronics
    Shahid Electronics May 11, 2010

    Do you have service manual or schematics of same model to check what can be cause of these resistors blown off?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 240 Answers

Look Do this
Replace your STK's
I dont trust them any more after all that info, wow

anyway
replace them
and yes you need Rz123 and Rz124 to be 3.9Ohm @ 2w don't sub.
Now also order a, 3.5a pico fuse for location Fd102s.


regards,
hope this helps you.
daniel.

Posted on Jan 12, 2009

  • Daniel Conklin
    Daniel Conklin Jan 12, 2009

    you have to finde the right parts no subing.

    and yes if you are yousing 1 wat and not 2w thay wiil burn..

    fuse is not on schematic its located under fins of heat sink on convergence ic's sum times ther are two of them. fd101s and fd102s

    samsung part number is 3601-001065 thay are all on convergance amp pcb.



×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I changed my two IC chips and three resistances on my Hitachi TV to fix color alignments. Now the problems is that yellow and blue double image are seen at the bottom of my screen with no much effect on...


Ur tv still have dead resistors parts,test all 12 resistors parts around the 2 STK convergence ICS and changes some more dead resistors parts or changes all 12 resistors parts for sure.If tv still have the same problems after tested and replaces more resistors parts or all 12 resistors parts.Than some how when u handling and replacing the 2 STK convergence ICS and resoldering the 2 STK covergence ICS u short it out the 2 STK convergence ICS by resoldering without proper grounding ur self not to allow for static electricity to kill the 2 STK convergence ICS or u using a soldering iron to high of a wattage for doing soldering ICS work.

Apr 23, 2011 | Hitachi 43FDX01B TV

1 Answer

Apex out of convergence


I have this TV and have fixed this issue. If you cannot adjust Red or Blue convergence, then your STK ICs are defective. The signal board or Digital convergence board is not able to adjust sig lines on the deflection board so pushing buttons does nothing. The STK's are your amplifiers for vertical and horizontal. This will require dissassembly and soldering. You'll need 2 STK392-020 IC's and 125v/5A pico fuse or buss fuse..

The STK's are mounted on 2 massive heatsinks. Can't miss it. Word of advice, LABEL the 3-4 Pin plugs B,G,R from left to right. These are your Vertical and Horizontal coils for each tube. Don't mix them up. I did and the tv survived luckily. Chances are if your STK's poped, then they took out the -25v line. Take out the power supply that is mounted vertically on the right. Look for a row of axiel lead fuses with "SOC 5000" printed on it. They look like white rectangular blocks with leads. Check them all. Particularly RF817. Sits next to RF814. The service manual lists it as a fuse and NOT a Resistor-Fuse like the label suggests. I found more than one typo like this. I replaced mine with a generic 125v/5A fast blow buss fuse. Soldered in a holder for it. Should work the same.

Took me abit to realize it was a fuse on the power supply. This -25 line traces to W057/W058 next to the first STK chip. Explains the symptoms.

May 12, 2009 | Apex Digital GB55HD09W 55" Rear Projection...

1 Answer

Sony tv


The STK's are probably blown again. You need to pay close attention to the resistors around the STK's. If you have ANY bad ones you have most likely reblown those chips. Let me know if this helps.

Oct 16, 2008 | Televison & Video

1 Answer

HCN4727W with Convergence issues


Mike,
The ICZ designations on that board are two Sanyo STK392-040 amps used for convergence. Rz142 through Rz145 are the yoke return circuit are 3.9 ohm 1/2w resistors. CZ140 and 141 are two electrolytic radial 22mf/50v caps in the feed circuit for those amps.
My question would be - and I've NEVER seen this, in my 30 years in electronics, what caused such a domino failure? The amps are basically LV fed by a +/- 24v line input. If the yoke(s) were to short shouldn't cause enough feedback to destroy the convergence board in the manner you've indicated here. That's a P58A chassis used in several models of the Samsung and Akai designs. Only trouble I've heard of with those boards are cooling and most techs have taken to installing cooling fans directly on the board, driven by the +/- 20v line. That drops the temp several degrees and allows the amps to operate at a much cooler temp. We rebuild those boards here on a daily basis and add the mods for greater reliability. But other than that the P58A is considered a bullet proof chassis.
Hope this helps!
Bill

William Rayburn, CET
Premium Technologies
PO Box 442
Long Beach, WA. 98631
360-642-4993

Sep 09, 2008 | Samsung HCN4727W 47" Rear Projection...

1 Answer

HCN4727W Convergence issue


Repalce STKs with 392-040 resistors should be 3.9 ohms,also you might want to join Repairworld it is for members who have TV shops over 7,000 different shops / lots of good techs there.They will not put up with anyone just looking to repair there own tv .Sorry unable to help with cz140,141.will do some checking you also can order whole convergence board.

Sep 08, 2008 | Samsung HCN4727W 47" Rear Projection...

1 Answer

TV set shuts down


3.9 ohm 2W

They are parallel in circuit and measure around 2 ohms when ok. Check the fuse associated with that circuit. FD101S 3.5 A

easyab

Aug 23, 2008 | Samsung HCM4215W 42" Rear Projection...

1 Answer

Colours not mixig together


you can get the new ic's at this sight i will post and free online tech support and they will also tell you the exact value of the resistors because when those resistors burn its because your ic's are no good I have used this service many times and the techs will go the distance to help people
http://servicemanuals.vstore.ca/

Apr 23, 2008 | Samsung HCN436W 43" Rear Projection...

1 Answer

Convergence


http://home.comcast.net/~dande76530/ConvergenceOutSchematiics.pdf
http://www.servicemanuals.net/results.aspx?type=SM&brand=15&model=AV-48WP74

Dec 17, 2007 | JVC AV-48WP74 48" Rear Projection...

3 Answers

Colors separated


You need change STK392-560(can use STK392-570)
I guess it happend when holding bolts weaken to radiator.(Check other STK on next radiator)
You have to change STK on right radiator.
Disconnect small connectors. You can l leave Hi Voltage two lines(RED). unscrew board.
Pool board out.
Unscrew STK. Set board verticaly. Just pool STK bu pincet and heatup solder. One by one...
Clean halles.
Set new STK with thermopasta on board in to hallsradiator. Screw up.
Wet contacts by liquid fluse. And sosler them.
Clean up by alcohol...Check for short by lense...
Set up board back...5515c27.gif

Apr 28, 2007 | Sony KP-57WS500 57" Rear Projection...

Not finding what you are looking for?
Samsung HCM4215W 42" Rear Projection Television Logo

278 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75178 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1689 Answers

Are you a Samsung Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...